What is Service Factor?
Reply
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
Reply
Why do I need to purchase a new shaft seal?
Reply
We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
Reply
Why should I purchase a Tune Up Kit?
Reply
A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
Reply
What are the dimensions on the shaft bearings or a part number and do you sell replacements?
Reply
The correct replacement bearing is part number 5270-31. The motor would require two. Here is a link to the bearing.http://www.inyopools.com/Products/07501352012909.htm
Reply
What go kit goes with a.o.smith 1.5hp 56y frame up rate motor 717721624?
Reply
Brant, The tune up kit is based on the pump housing model not the motor. If you can get us the pump model, we can help you find the correct kit.
Reply
I need to replace a Magnatek Centurion Switchless Motor 1 1/2 HP, 3450 RPM, 230/115 v., Type CX. The part number is showing 8177080-40. Is this the correct replacement?
Reply
Hello Catthy - The B854 motor would be the correct 1.5HP replacement motor.
Reply
what shaft seal goes on C105-137PEB impeller. and does impellers ever wear where shaft seal goes against impeller?
Reply
Brant, You have a Sta-Rite Dura-Glas/Max-E-Glas Pump. This pump have a STA-RITE SHAFT SEAL OEM (PRE-1998) and a STA-RITE SHAFT SEAL OEM (NEW STYLE) so you'll have determine which one you need. Yes, the impeller and diffuser do wear out over time.
Reply
Do you carry a Tune-up kit for a waterway champion. I am looking to replace my current motor that is DOA & cannot find the Manufactures name on your tune up list.
thanks
Reply
Hi Marco, We do carry all of the Individual Parts for the Waterway Champion Pump but unfortunately there is not a tune up kit for the Champion pump so you would purchase the parts individually.
Reply
I have a a.o.smith centurion 1.5 hp. Cat.-29, serial # 210083m,
Part # 7-164304-24
3450 rpm
Code H
Is this the correct replacement.?
Thanks
Reply
I have A.O.Smith B848 Centurion 1.0 HP motor, Can I replace1.5HP B2848 motor instead?
Reply
Hi Vasant, If you currently have a B848 motor then I would suggest staying with the 1 HP B2848 Motor. The reason being is that most likely your filter was sized to be able to handle a 1 HP pump and possibly the 1-1/2 motor will be to powerful for your filter. If you decided you definitely want to go up to the 1-1/2 HP Motor than you would need the B2858 1-1/2 Full Rate Replacement Motor you will also need to change your impeller to a 1-1/2 HP impeller and we would need to know the model of your pump to make the impeller reccomendation.
Reply
I need to replace a Centurion motor - part number 10-168787-07 56y will this work for me?
Thanks!
Reply
Carl- No the motor you need is a Motor 56y Sqfl Full 1.5hp (b849). The B854 is an uprated motor,based off the part number you provided you have a fullrate motor.
Reply
I have a whisper flow motor serial # BJ 12-185 part 8-177456-03 that I need to replace. What replacement motor do I need?
Reply
Reyna, Based on p/n 8-177456-03 the replacement motor is a 1.5 HP Dual Speed Full Rate Motor (B983), you'll also need a Whisperflo Tune Up Kit (GOKIT).
Reply
is this motor the same is the AO Smith Cat: B854 Part: 0-177216-24
Reply
Hi Ray, Yes b2854, 717721624 is the same as B854 Part: 0-177216-24. When you check your motor label against the picture of the listed motor, the specification will be the same.
Reply
I have a Jandy Stealth 2hp pump motor that went bad. This pump is only used for two waterfalls, and pumps too much water and causes overflow problems. Can I switch just the motor out to a 1.5 hp while keeping the rest of the pump assembly intact?
Reply
Depending on the model of Jandy Stealth, yes you can. There are two different versions. To switch down a motor size you would just need to downsize the impeller and the diffuser. Other than that, all the other parts can stay the same.
Reply
does this motor have steel bearings?
Reply
Hi Dan, yes this motor does use a steel caged bearing. You may view the Bearings Used in This Motor here.
Reply
Is this the correct replacement for an AC Smith Centurion switchless motor part# O-193986-24? If so other than this motor what else will I need to successfully replace the old burned out motor part# O-1963986.24?
Reply
Yes this is the correct motor replacement for you. The only other items we would recommend for your motor job would be the go kit that contains the seals and gaskets. We would need the front plastic pump housing model that the motor is mounted to in order to cross reference that seal kit for you.
Reply
We need to replace an A. O. Smith Century Centurion motor, not sure if this is the one we need. Label says: Serial: BY11-12, Part 7-177475-20. We have WhisperFlo WF-26. The pool guy said we need a full rate, but found the pump model number under up rate.
Reply
You can use this model motor or the full rate B848. Both thave the same general specifications.
Reply
I like to rebuild my Jandy PHPM1.0 into 1.5 HP pump. My plan is buy this motor with #5020-141 impeller. What else do I need to buy?
Reply
Steve- You are correct, that impeller part number 5020-141 Impeller, 1 Hp Full, 1-1/2 Hp Uprate, is the correct one. I would also recommend chang changing out the shaft seal.
Reply
I have a centurion pool/spa motor, part #0-193985-04 and need to know how many gallons per minute/hour it cycles? Please email me the info.
THANKS!
Reply
Unfortuanately, the answer can not be gotten from the motor alone. We would need to know what pump housing this motor is attaching too. The aquadynamics of the pump housing is what affects the GPM.
Reply
Model number ECM16SQU is the variable speed replacement for model B854 (B2854). Will this fit on the Jandy PHPM1.5 Pump housing?
Reply
Phil, the 1.65 HP Variable Speed Pool Pump Motor Square Flange ECM16SQU will work on your Jandy Plus HP 2006-Current PHPM & PHPF. I would also recommend a shaft seal.
Reply
Can I use the whisperflow shaft seal for this model? and is it the ps 1000?
Reply
If the model of the pump housing is a Whisperflo or a model that uses the PSR 1000 seal then you can. Shaft seals needed depend on the model of the pump housings that motors are mounted to.
Reply
I have A. O. Smith serial # BY06-16, Part # 7-193633-24. 1.5 hp. Type cx, Fr P56j What would be the replacement part for this motor.
Reply
Hi Tim, The A.O. Smith 1.5 HP Full Rate 56J Motor (B129) would be the correct motor that will replace p/n 7-193633-24.
Reply
whats the difference in a up-rate & full rate motor? how do i tell which one i have
Reply
George,Up rated and full rated help determine your total horsepower. I recommend you take a look at our blog, "Is a 1.0HP Motor the Same as a 1.5HP Motor?" to read up a little more on the difference and how you can determine which one you currently have.
Reply
how hard is it to replace the front & rear bearings on this motor & does it take special tools? thanks, ps. the rear bearing only lasts for about 6 months then starts growling, i take it in to local shop at 100.00 a crack. they have replaced the bell end twice?? i also have tried another shop with same results. is there a heavy duty rear bearing for this motor or is this common, thnx
Reply
I have a 5KC39UN6086X Marathon motor that I would like to replace with this model. It is attached to a Jandy PHPM 1.0. I noticed that a shaft seal is recommend when purchasing a new motor; however, I'm not exactly sure which one to purchase. It's a saltwater pool with a Jandy PHPM 1.0 Housing. Thanks.
Reply
Jason,All of your seals pertain to the make and model of your pump end. The correct shaft seal for your Jandy PHPM pump is 5020-086 (old style) or 5020-087 (new style).The best way to tell is by the serial number listed on the pump body (housing). The old style seal is used with serial #s prior to P08FF0001. If you have the above serial # or later, you would use the new style shaft seal.
Reply
Need a replacement motor for a pentair model 346206 , what part numbers do i need? thanks
Reply
The correct motor replacement for the 346206 Pentair Challenger motor is the B854 1.5 HP Uprated. Do not forget to add a shaft seal or GOKIT5 to the motor replacement.
Reply
I need a century centurions pool motor
Part 7-177215-04
HP 1
Reply
Marilyn- When I searched for your 7-177215-04 I was able to pull up B853 A.O. Smith 1 HP, 56Y Frame, Up-Rate Motor (B2853).
Reply
Will this motor work for a Hayward Tristar pump? The current motor is a Century 1.5hp, 1.10 sf, y56y frame, 230/115V.
Reply
Hi Thomas, This motor can replace the current motor that you have on your Hayward Tristar pump.
Reply
will this replace the flopro 1.5 hp model# fhpm1.5
Reply
Hello Steven and thank you for your question. Yes! The A.O. Smith 1.5 HP, 56Y Frame, Up-Rate Motor will replace your current motor. We recommend replacing your Shaft Seal when changing motors. Also, inspect any other o-rings that may appear damaged or worn. You can find the Jandy Flo Pro Pump FHPM parts here. Thanks again, Alan.
Reply
I am replacing a motor on my WhisperFlo WFE-6 pump. I see that this motor is an "Up-Rate" motor. I've read that if you go with an Up Rate motor, that this may require you to increase the HP, is this true. Or, is this the proper motor for my pump. thanks
Reply
Hi David, The WFE-6 pump replacement motor will be the A.O. Smith 1.5 HP EE Full Rate Motor (B2842) which has a total hp of 2.21, verses this B854 motor has a total hp of 1.65. The A.O. Smith 2 HP, 56Y Frame, Up-Rate Motor (B855) would be the up rate replacement for the WFE-6 pump. We also would recommend getting the Pentair/Purex Whisperflo Tune Up Kit GOKIT32 or GOKIT32SALT depending on the your sanitizer.
Reply
I have a A.O. Smith 3/4 HP B625 I believe it is part#7-173848-23. Which is the replacement.
Reply
Kathy,If your motor part # reads B625(7-173848-23) then your replacement is B625 and can be seen here. Don't forget to get a new shaft seal as well!
Reply
My motor is slow to start but when running runs well. I think the issue is the capacitor. Can this be purchased separately?
Thanks
Reply
Would please tell me which propeller (Brand and model#) will fit the A.O. Smith 1.5 HP, 56Y Frame, Up-Rate Motor (b2854, 717721624)? Thank you.
Reply
The impeller type would be dependant on the front pump housing model that the motor bolts to.
Reply
Does this pump come with gaskets
Reply
The motors do not come with any seals or gaskets besides the slinger. For the seal kit we would need the model of the front pump housing that the motor bolts to in order to cross reference that kit for you.
Reply
Pool Motor I currently have is very noisy which came with the house. We own a Purex Triton Challeger 1 1/2 HP Motor. It's a high performance pump and it's for PAC-FAB. AMB:40 TYPE:CX FORM: KJM FR: Y56Y RPM:3450 Hz: 60 PH:1 Code: J Serial BU3-03 and it says horizontal with vent holes down. We want to make sure we purchase the correct motor. Also, what is the cost of replacement motor. The front housing still in good shape also PAC-FAB.
Reply
If the Service Factor (S.F) on your motor label indicates 1.47 or 1.5 then you will need the 1.5 HP Full Rate Challenger Motor if your S.F indicates 1.10 then you will require the Challenger 1.5 HP Up Rate Motor. When replacing your motor we would suggest a Challenger Seal Kit to make sure you have no leaking with the replacement motor.
Reply
Will this motor work as a replacement t for my pentair WF-26 1.5 hp pump?
Reply
Hi Mike yes this is the correct replacement motor for your Pentair Whisperflo WF-26 pump. Also whenever you replace your motor you will want to go with a Pentair Whisperflo Shaft Seal Kit as if you use your old seals they have a tendency to leak.
Reply
I have an inground pool that is 19 years old and I am still using the original pool pump. It's time to buy a back up pump but I have a problem identifying the size of my current motor. My original pprwk said we were going to get a 1HP mtr but I remember the owner stating he was going to upgrade us to a 1 1/2HP because we were good friends. The metal tag on the motor cannot be read. On the motor is Pinnacle high flow pump Magnatek Centurion switchless motor 16718001 How can I tell what size ?
Reply
Hi Mike, That's a great run on your pump 19 years! This would be the correct replacement motor for your Magnatek Centurion switchless motor 16718001 if you are just looking to replace the motor and not the entire pump. If you want an entire pump then the Pinnacle is no longer being manufactured so you will have some re-plumbing. If you decided to go with entire new pump then I suggest the 1.5 HP PureLine Prime Pump. If you do decide to just replace the motor then you will also need a Pinnacle Tune Up Kit.
Reply
I have a WhisperFlo Model # 26C. I need to replace the motor. I believe the replacement motor would be the B2854. Is that correct? What impeller would go with this motor? Also, what seals and rings should I be looking to purchase? Thanks.
Reply
Hi Alan, The B854 motor is the correct motor for the WF-26 pump. The Impeller - 073128 and GOKIT32 or GOKIT32SALT will be the impeller and tune up kit for the WF-26 pump.
Reply
I need to replace the motor on a WF-26 (Whisper Flo 26, 011773). It is a 1.5 hp motor. Also need a shaft seal (salt pool). Is this the right motor? Can you also help me with the shaft seal for a salt pool? Thanks!
Reply
Hi Tom, The B854 and Whisperflo Saltwater Tune Up Kit - GOKIT32SALT are the parts needed to get your pump up and running again.
Reply
I have a 40+ year old Anthony Apollo filter system that works quite well. About 15 years ago I replaced the original pump motor with an AO Smith model number K48M2N111A3 serial number 7B00 1-1/2 HP motor. It is a 3450 RPM motor that includes an FR 56C designation on the data plate. Also appearing on the data plate are SK1152 and CET 36WX. Is there a replacement for this motor? Thank you.
Reply
Will this replace a AO Smith CAT B854, part 7-177216-24, type CX, fr Y56Y, 1.5 HP motor? How long is the warrenty?
Reply
Andy,Yes, this is the correct replacement for your B854 motor. All new motors come with a one year warranty.
Reply
Good morning! I have an AO Smith part #7-F56AA12A04-24 serial#154093M. Would this be the correct replacement for my motor? Also, what GOKIT would go with it? THank you...
Reply
Hi, This motor can replace p/n 7-F56AA12A04-24, we will need to know the model of the pump housing (what the motor bolts to) in order to get you the correct seals.
Reply
Hello. I have a dead Magnatek Centurion SE motor fitting into a Jacuzzi Magnaforce body with 17969301 on the round plate as a motor identifier - I don't know if it's a 1.5 or 2HP - the motor label is not readable - what would be the replacement motor and trim kit to seal? Pool is 13,5000 gal. and 50 ft from the equipment with no spa. Also, does the impaler assembly simply bolt off/on or are there special procedures for removing/ reinstalling? Local motor shop is first checking capacitors.
Reply
Yes sir that is the correct part number for the replacement motor, B854, and the seal kit is part number GOKIT14. As far as the install, we do videos on our website in the 'How To Guides' tab that can walk you through it. If you have any further questions don't hesitate to email back.
Reply
Hi, i'm trying to replace my pump but there is no model number on it. It seems very similar to this one but all it has is a PART O-193986-24 it might be an older pump. Also the INSUL class is B and everything else looks the same.
Reply
Hi Evelyn, Yes this B2854 motor is the proper replacement for your O-193986-24 motor.
Reply
We have Century Centurion B849 serial # BY04-14 I believe it says PART: 7-1777896-22 1.5 HP FR Y56Y SF 1.50 PH 1 HZ 60 rpm 3450 Volts 230 AMPs 230
Code J Insul class B
can we replace it with this pump?
Reply
Kelly, You will need to replace it with the B849. If you replace it with the B854, you will burn out the motor.
Reply
I need to replace the motor on my 10+ year old Sta-rite Dura-glas P2RA5E182L pump. The current motor is a replacement CAT B848; Part 0-177080-24; y56y; HP 1.0; SF 1.65. Which motor do you recommend please?
Will need to replace a C105-137P EB impeller and ceramic seal also...
Thanks
Reply
Hi Shannon, This motor is the exact same motor as the B848 Motor so I would go with whichever is less expensive. The impeller and shaft seal for your pump can found on the Dura Glas Pump Parts Page.
Reply
We need to replace an A. O. Smith Century Centurion motor part: (7-193993-05). Which is the correct replacement for this motor?
Reply
Does this replace pump model # PHK2RA6F-103L
Reply
Hi, The B854 motor is the correct replacement motor for the PHK2RA6F-103L pump. You will also need to replace the shaft seal and the other o-rings which can be found on the Sta-Rite Super Max Parts page.
Reply
Will pump replace a 12 year old Sta-rite Dura-glas P2RA5E182L pump? And if so, can this be done without making any other modifications.
Reply
I have a MagneTek Century Centurion Pool and Spa Duty Pool Pump withe serial BR6-197 that I need to replace. I can't find the exact pump, maybe they don't make them anymore. What is your advice/what should I be looking for?
Thank you!
Reply
Hi, We're unable to look up serial number info so I can't say which motor you have. If you can send us photos of the motor label we can try to locate the correct replacement motor.
Reply
I have a mustang frame 56 pool pump. The
I'd tag is worn out but I do see serial
177216 24 is this the correct replacement b2854
Reply
Hi, Yes, the B2854/B854 motor will replace the motor you currently have. The seal of the pump will also need to be replaced, they can be found via the Waterway SVL56 Pump (Mustang Inground) Parts page.
Reply
ours says marathon and not century will it still fit our whiserflo wf26 1.5 horsepower? is there a generic pool pump cheaper
Reply
Hi Donna, This motor will fit the Pentair WF-26 pump, there is not a cheaper option. We also recommend getting the Pentair/Purex Whisperflo Tune Up Kit (GOKIT32).
Reply
I purchased this motor currently on our pump in 12/10/2015, it appears the motor windings may be shorted to ground, I noticed this time while looking at buying a replacement the motor had a one year warranty, is this pro rated or full replacement. Also is there a motor from a different manufacturer that cross reference with this one? Thank you, Mike
Reply
Hi Michael, Its a full replacement warranty. We only sell Century motors.
Reply
Will this motor fit on a sta rite dura glass II pre-1998 p4ra ? Thank you
Reply
Hi Lorena, This motor can be used on the Sta-Rite Dura Glas II pump. If you can provide us with the MOD, PART or CAT number we can confirm if this is the correct motor you need.
Reply
Have a Pentair Challenger pump with an Emerson motor.. Model K63CXERY-4786 HP-1.5 SF -1.10 Hz-60 Volts 230/115 Frame 56Y MFG-M807C...which replacement motor do I need?
Reply
Hello, David. The A.O. Smith 1.5 HP, 56Y Frame, Up-Rate Motor (b2854, 717721624) is for single speed. Do not forget to replace the Pentair Shaft Seal OEM 5/8" - 354545S any time you replace a motor. We do offer the Tune Up Kit, Pentair Challenger Pump - GOKIT5 this Gokit is for the Challenger Hi-Head pumps. The Gasket for the Diffuser and Front Housing of the Medium Head pumps are sold separately under part numbers Housing Gasket (355329) and O-ring, Diffuser (square Ring) Medium Head (355030).
Reply
wil this motor replace a marathon motor wf 26 whisper flo 1.50 horsepower pump i see it says cnetury ot marathon is it the replacement for my pump.
Reply
Yes, this is the correct replacement motor for the WF-26 Whisper Flo Pump. I would also recommend a Tune Up Kit Pentair/Purex Whisperflo - GOKIT32 that includes the replacement shaft seal and o-rings for your pump.
Reply
Wil this pump listed A.O. Smith 1.5 HP, 56Y Frame, Up-Rate Motor (b2854, 717721624) replace a Century centurion A.O.Smith serial #BZ06-30 Pa # 7-177475-20
Reply
The correct replacement motor for the motor model #7-177475-20 is the 1 HP Standard Motor - Full Rate (B2848).
Reply
Hello - will this motor work to replace an Anthony Pools 1 1/2 HP pump motor? Nameplate on the motor is burned off. Frame size is 56Y (based on through-bolt distance of 4 1/8"). Only specs I have are from 30+ year-old literature; 1 1/2 HP, 3450rpm, 100gpm. Thanks.
Reply
Hello to better assist you please look at Anthony Centrifugal Pool Pumps Parts to see if this matches your pump. If it is the correct motor is sq1152 just make sure to look at specs matching up your frame and SF. Also I would recommend pump seal 5056-08.
Reply
I need to replace A. O. Smith 1.5 hp, SF 1.10, FR y56y, type CX, volts 230/115, amp 5.1/16.2, class F, Part #7-56AA12A04-24, H-E tristar motor
can you tell me which motor I should use?
Thank You
Reply
Hi Bii,You can use this B854 motor or the SPX3210Z1MR (OEM) motor as a replacement.
Reply
Looking for a replacement motor for our Pentair CFII N1, 1.5A / PN 343234. Motor part number is 196250. Will this one work?
Reply
Hi Brian, The B854 Motor is the correct motor for the Pentair CFII N1, 1.5A / PN 343234 Pump.
Reply
will this replace the motor for a sta-rite PHK2RA6F-103l
Reply
Hello, The correct replacement motor for the Super Max 1.5 HP Pump - PHK2RA6F103L will be the A.O. Smith 1.5 HP, 56Y Frame, Up-Rate Motor (b2854, 717721624). Whenever you change out a pump, I would also recommend changing out the Pump Seal 200 (psr 200) 5/8".
Reply
I want to replace a Centurion SE for Anthony pump motor with Serial # BP2-21. Marked as a 1.5HP unit. What is the correct replacement motor for that?
Reply
Hi Per, We're unable to cross reference serial number to their products. To confirm if the B854 motor is the correct replacement we will need to know the service factor, and or the part number.
Reply
Is this the correct motor to replace an AO Smith Centurion #0-193985-04
Reply
Hello, The correct replacement motor is the A.O. Smith 1 HP, 56Y Frame, Up-Rate Motor (B2853) for the motor model number #0-193985-04.
Reply
What is the correct replacement for 1 HP 1.25SF Century centurion on a whisperflow Part # 8-177474-01, Type CX , FR P56Y, PH 1, HZ 60, RPM 3450, VOLTS 230/115, AMP 7.1/14.2, Time CONT, ENCL DP, FORM KJM, CODE J, INSUL CLASS B AMB 40C
Reply
Looking to replace a rusty and increasingly loud Pentair 7-177475-20 1.5 HP pump. This looks to be a match from everything I read. Accurate?
Reply
Hi Brett, The B854 motor is the correct replacement for p/n 7-177475-20.
Reply
Do you have a chart or some piece of literature that explains what the codes are? For example, what the code F would be, or say, the code J would be? I need a motor replaced on a pool pump and would like to buy one with the exact specifications. Thank you,
Reply
Hello, Joe. I best recommend contacting Regal Beloit at 1-937-667-2431 as they are the manufacturer of both Century and A.O. Smith Motors. Unfortunately, we do not have a chart that identifies what each code means.
Reply
Is this the replacement motor for a Centurion (PAC-FAB), 230/115 Volts, 3450 RPM, Type CX, Part# 8-16845323? Also need a pump gasket kit for a PAC-FAB pump of same vintage, circa 1970-1980. Only slightly legible number I can find is either 30-0000 or 30-0300 next to brand name. Thanks.
Reply
Yes, the B854 would be the correct replacement for your pump.
Reply
Does the the b2854 1 .5 motor come with a seal or is it a separate purchase?
Reply
The shaft seals need to be purchased separately and would based on the model of the front pump housing that the motors bolt to.
Reply
I have a Flotec Model AT251501-01 that is only a year old but unfortunately got flooded a few times this season and died. Is this the correct replacement motor and what seal will I need to replace it?
Reply
David, You can either use that motor or the Energy Efficient motor recommended on the Flotec AT251001 & AT251501 Parts Page. Key #7 is the shaft seal, any one of those would work.
Reply
The part number on my pump is either an 8 or B 8-177475-20. both are about 20 years old. Is this pump the correct pump.
Reply
Good morning Terry, When searching the part number you provided us. It is coming up as a Full rated 1hp motor. Which is like having a 1.5Hp pump. Its rated horsepower is 1.65 you will need to have an impeller for a 1.5hp pump.1 HP Standard Motor - Full Rate (B2848)
Reply
I have a Pentair Superflo High Performance Pump model 340039. The motor model # is 196239. This motor looks like the correct replacement. Is it?
Reply
Hi Jay, Yes, the B854 motor is the correct replacement for the Pentair SuperFlo Pump model 340039. I would also recommend replacing the shaft seal, o-rings and gasket for this pump which are all located on the Pentair SuperFlo Pump Parts page.
Reply
I have what appears to be a 7-177215 or 7177215 with a cat. Number of BZC6-28, what part number motor would I need to replace it with?
Reply
Hi, Sal. The 1 HP, 56Y Frame, Up-Rate Motor (B2853) is the replacement for the 7-177215 motor.
Reply
I ordered this replacement motor for my pool but I didn't order any new seals. Should I order new seals and if so, which kind?
Reply
Good morning Ashley, Yes, I would recommend changing the shaft seal and 0-rings you can find those in a gokit. I would need to know what kind of pump you have to give you the correct kit.
Reply
I have pump PHK2RA6F-103L STARITE. Is this the correct replacement motor and what other parts would be needed to change this motor?
Thanks
Reply
Hi, Steve. This B854 motor is the correct replacement for the PHK2RA6F-103L pump. The Shaft Seal (PSR 200), Diffuser Gasket (355030) and Housing O-ring (355619) are the recommended items to replace when replacing the motor.
Reply
I have AO Smith B854 motor for my pool with a total HP = 1.65. Do you have parts to rebuild? The motor is making loud noise. If not, let me know the replacement part no. along with any kits I would need.
Thanks.
Reply
Looking at 1.5 hp motor but also need impaler ? and O rings/seals. Do you have that in a kit?
Reply
Hello Bob- Unfortunately the impeller and seals depend on the model pump that you have not the motor. What is your pump model number?
Reply
I have a dead Magnetek type cx,60 hz,code j,cat b849 serial#bw1-16 what would be a replacement for this model on my Haywood pump?Thanks in advance...
Reply
Hello Cheryl- The A.O. Smith 1.5 HP, 56Y Frame, Up-Rate Motor (b2854, 717721624) is not going to be the right motor for your CAT # B849. The currently replacement for your motor is the Motor 56y Sqfl Full 1.5hp - B849.
Reply
I have a Pentair Chalenger pump motor 7-168453-24 56Y frame 1.5 HP SF 1.1.... Looks like this should be the replacement motor I need.. Just wanted to make sure before I order.
Thanks
Reply
Good afternoon Nate, I am showing a 1 HP Standard Motor - Full Rate (B2848) as your replacement it is a 1hp with a service factor of 1.65 giving a total HP of 1.65.56Y frame
Reply
Hi, I have 7-193993-05 Pump. What would be a replacement part?
Reply
Hi, Mark. The Century B2841V1 Full Rate EE Motor would be the exact replacement for P/N 7-193993-05 but you can also use this B854 standard motor.
Reply
Some confusion, before placing an order. I have a 1-1/2 hp pump 7-177475-20. Your description on b2854 says it is 1.5hp but never states my part # in the description or on section of pumps that this will replace. Additionally b2848 says that it replaces 7-177475-20,,,but this is described as a 1hp pump.???
Also, my pump currently is making loud noises,I'm assuming bearings, but I do not intend to install this pump until needed. What would be your return period, should I need to return ??
Reply
Good afternoon, It is the B2848. It shows up under alternate part #'s. 30 days is the return period. If you let me know what type of pump this is going on. I can recommend a seal kit.
Reply
Do you have a bearing set for a b2854 pool pump? I need both bearings.
Reply
We do not show those motor bearings listed. You would need to contact A.O. Smith at (800) 262-6484 to confirm those part numbers.
Reply
I have a Century Centurion AO Smith pool pump motor, part number O-193986-24. Is this the replacement motor? Is there any issue(options) with the connection to the pump? My unit looks square. I have a Jandy System.
Thank you
Reply
Yes, that would be the correct motor replacement. I will need the Jandy pump model, not the motor, to find the correct shaft seal though. If you do not know please attach a side view picture of your complete pump so I can help you with that.
Reply
I have a Jandy System that is 4 years old.
The motor is going to ground and the breaker will not reset. Electrician said motor is bad.
It has a Century Centurion AO Smith pool pump motor, part number O-193986-24. Type CX Frame Y 56 Y
The pump is a Jandy FloPro Series, model FHPM.
What is this the replacement motor? What pump seal kit do I need?
My unit looks square.
Are there any issues(options) with the connection to the pump?
Thank you
Reply
The correct replacement motor would be the A.O. Smith 1 HP, 56Y Frame, Up-Rate Motor (B2853). There is not a seal kit available for this pump currently, but you will need to replace the Shaft Seal (R0479400) OEM whenever you change out the motor. Here is a link to the Jandy Flo Pro Pump FHPM Parts page for your reference in the event you need additional gaskets, o-rings, or parts.
Reply
I have a Jandy Pro Series Pump, Model FHPM 1.5 single speed. Is there a way to convert it to 2 speed? This pump is used for Spa Jets and it is too strong. Another idea would be to use a valve to restrict the drain water into the pump. Would this work or would it damage the pump?
Thanks.
Reply
Hi, Albert. You can use the 2-Green B2982T Motor as a replacement. You can use a valve to restrict the water flow to the pump but you'll have to ba careful not starve the pump. The pump will let you know when there is not enough water coming into the pump.
Reply
on a Pentair / Purex Wisperflow pump Model #wfe-6 ssn 12-01-0520AP, with a AO Smith 196246 Electric motor, what type or screw size and fastening head, (Phillips, Allen, Size)holds down the impeller?
Reply
The thread diameter is 1/4" and the length is 1".
Reply
we just bought our house. we have a 9000 gal kidney pool. there is a heat pump heater Hayward HPC-1,
model PE52A2 that runs but does not heat the water. i am thinking of replacing it with a Hayward HP21104T
because it looks like a one for one replacement. there is a Pentair WisperFlo pump with a century B2854
replacement motor on it. when the motor starts it delays for several seconds
is there a kit or something to repair the motor or just replace it? thanks
Reply
Yes, the HP21104T would be the replacement for your current heat pump. As for your WhisperFlo the replacement motor B854 and seal kit is GOKIT32 unless you have a saltwater pool then it's GOKIT32SALT.
Reply
My motor starts and runs for about 10 seconds then shuts off, restarts in a few minutes runs and then shuts off again. My pool service changed the capacitor and that didn't fix it. Now they tell me the motor needs to be replaced, is there anything else internally that can be causing this
Reply
You may review our How To Troubleshoot a Pool Pump Motor - Motor Shuts Down or How To Troubleshoot a Pool Pump Motor - Motor Overheated
Reply
I have a Centurion 7-168453-24 pool motor. what will be the replacement motor for this model and what shaft seals do I use for it? the current pool pump is model Pentair Challenger 1.5 HP.
Reply
Hello. I have two identical motors that need to be replaced -- the existing ones are MagneTek Century Centurion 168345, Frame Y56Y. The pump for each is the PacFab CHII-N1-2A. These pumps are only used rarely, one to run the spa jets and one to run a couple of fountain bubblers in the main pool.
Is this the right replacement motor for my needs, and if so what else do I need to purchase at the same time (shaft seal, etc)?
Given the limited use of these, are there any lower cost options?
Reply
Hello Jarrett- No that will not be the correct motor. The model pump you have is Pentair Challenger 2 HP 115/230V Single Speed, UR Pump - 346201 (CHII-N1-2A). The motor that will work for your pump is the A.O. Smith 2 HP, 56Y Frame, Up-Rate Motor - B855. We would also recommend the Tune Up Kit Pentair Challenger Pump - GOKIT5.
Reply
My pool pump has gone out and according to the Part# this is an exact replacement. Is there anything else I will need to put this on to replace my burned out pump? I am unfamiliar with this installation and am hoping I have everything in order to swap them out. I have pictures of my pump and filter but did not see how to attach so you can see and give accurate assistance. Thank you for your time.
Reply
Frank, You will need to replace some of the pump gaskets as well. If you can provide photos of the motor label and pump, we can help you find the parts you will need.
Reply
Is this motor interchangeable with a Jandy JHPU 1.5 (part # 7-193632-24)
Thanks!
Reply
Hello Dan- The A.O. Smith 1.5 HP, 56Y Frame, Up-Rate Motor (b2854, 717721624) will work with your Jandy JHPU1.5.
Reply
I have a pentair challenger 1.0 hp motor/pump system and need to replace the motor. Can I use the AO Smith 1.5 hp as a replacement motor without changing the impeller?
Reply
Hi Vic, You would need to upgrade your impeller to the 1.5 HP impeller if you upgrade your motor to 1.5 HP. The reason being is that if you stayed with your 1 HP impeller then you would be paying the operational cost to run a 1.5 HP motor but only getting the water output of the 1 HP impeller.
Reply
My motor was still running when It started squealing with a high pitch sound. I saw water leaking from between the housing and the motor. Not exactly sure where. What else is needed besides the motor? Do need the Seal Plate- Almond - 356012?
Reply
Hi, Michael. You will need to replace the pump shaft seal along with the o-rings inside of the pump. That particular seal plate can fit on the Pentair / Pac Fab Pinnacle Pump and the Pentair Superflo Pump. You can click the links provided to view the available parts of both pumps which will have the parts listed.
Reply
Hi, I have two WhisperFlo pumps with motors that need to be replaced. Both pumps are model WF-26, 1.5HP, SF 1.10.
One is the main and the other is a feature pump. The main is part number 7-17745-20. FR Y56Y. It's amp draw is 8.0/16.0.
The feature has part number 7-186236-20. FR P56Y. It's amp draw is 5.4/10.8. The replacement motor you sell shows a frame of 56y. Will that work with the Y56Y and the P56Y? Can the replacement be used with my feature pump with the higher amp draw?
Reply
Hi, Don. The B2854 motor which is the replacement for the WF-26 pump and the B2846 motor which replaces p/n 7-186236-20 are the correct replacement motors that will replace the P56Y frame motors. You can increase the motor with a higher hp motor which will require also replacing the impeller and other parts. I would also recommend purchasing the Pentair Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
I need to replace my pool pump motor - pentair motor 196250, 1.5 hp which is connected to Challenger pump 346206. Is the B2854 motor the replacement?
Reply
Hi, Ed. Yes, the B854 motor is the correct replacement. You also need the Challenger Tune Up Kit - GOKIT5 which includes all of the seals.
Reply
I need to replace my filter pump I had a Century Centurion A.O.smith 2hp, would PART#B854 1.5HP be a sufficient replacement pump?
Reply
You would actually need the specific motor model, part number or catalog number to cross reference the correct motor.
Reply
pump motor is squealing. I have a Pentair whisperflow Model 196239, WF-26, 1.50 hp, 208-230/115 V, 60 HZ, 3450 RPM, S.F. 1.10, Max Amps SF 7.8-8.0/16.0, Code F. Insul Class F, Amb Tempe 50, time Rating Cont
Will this work and if so what gaskets would I need as well when replacing.
Reply
Yes this motor will work. The seal kit that you would need is the GOKIT32 and is the GOKIT32SALT if you have a saltwater swimming pool.
Reply
Turned on my pump for first time and after priming the motor started smoking. it didn't sound great when priming and seemed to lose pressure as water was not squirting out of relief valve. i have Century Centurian motor. Part # 7-193986-24. will this motor be the correct one to replace it?
Thank you
Reply
Yes this would be the correct motor replacement. Also, it would be wise to replace the seals and gaskets during the process. If you need assistance cross referencing that please provide us with the front pump housing model name or number. You can call in with that information or if you do not know then you can email us a few images of that housing through our support request page.
Reply
I need to find a replacement pump. I have a photo of the label from the old one - where can I send that for help?
Reply
For further assistance, you can send images to upload@inyopools.com or through our support request page.
Reply
I have an old A.O. Smith motor that's been rebuilt. It is 7-177216-24. Is this the correct replacement? What impeller kit and diffuser kit goes with it? I need that too.
Reply
Yes, this is the correct replacement motor. Those kits will depend on the model of the front pump housing that the motor bolts to. Please call in with that information or you can submit images of that housing through our support request page so we can further assist.
Reply
For the new motor I just ordered, do the seals come with it for installation?
Thank you.
Reply
When you order a motor the seals do not come with the motor as we would need to know the make and model of your pump to determine the seals. Could you let us know which pump you have? Common models that this motor works on is the Pentair Whisperflo, Pentair Challenger, Jandy Stealth, etc..
Reply
Will this replace part # 7-f56aa12a04-24? It is a Century motor off a Hayward Tristar pool pump. All the other numbers (HP, frame, SF, etc) match perfectly but I can't find this particular part number anywhere. The only other number that seems relevant is SP3210z1m, and that it is a 1081 pool pump duty. Thanks.
Reply
Hi Matt, Yes this would be the correct replacement motor for your 7-f56aa12a04-24. We would also suggest a Tristar Shaft Seal when replacing your motor.
Reply
Need a replacement pump and the seal kit for:
Pentair, WhisperFlor, Part 7-177451-03, FR Y56Y, Type CX, HP 2.2 SFHP, 1.1 SF, Volts 208-230, Amps 9.6-8.8
Can you send me the AO Smith replacement number along with the kind of seal kit and any other parts I need? Thanks.
Reply
The replacement motor is the B842 and the seal kit is the GOKIT32 and for a salt water pool, it is the GOKIT32SALT.
Reply
Are both models 3/4 horsepower . Could Ig replace with a mogdel
With Higher hp model - say 1.5?
Reply
Hi, Sully. You can replace your existing motor with a higher hp motor if your system can handle the water flow. You will also need to replace the pump impeller, diffuser, and seals.
Reply
The motor quoted is a 1.5 hp (A.O. Smith 1.5 HP, 56Y Frame, Up-Rate Motor (b2854, 717721624) but the Pentair specifies a 2.0 HP - do you have one of those? Your QAs mention that using a lower HP on a casing will cause the motor to burn out. Thanks.
Reply
Hi Mary, Could you reply with a photo of your motor label and a wide shot showing your complete pump? This would help determine the proper replacement motor for you. You can reply to this email or email to upload@inyopools.com
Reply
Can the B2842 motor be replaced with B2854 on a Pentair Whisper flow pump?
Reply
Scott, The 2 motors are not interchangeable. The B2842 is a 1.5HP Full Rate motor and the B2854 is a 1.5HP Up Rate motor. The total horse power is not the same between the 2 of them.
Reply
what mfd rating is the run capacitor? it failed July 4th(ugh). luckily I had a 20mfd/370vac, as I'm an HVAC tech. old cap has no legible info left on it. fyi....20mfd/370 got it working. I suspect it's a 30/370. just want to be sure. thanks!
Reply
Hi, Bill R. This B854 motor requires a 30 MFD 370V or larger Run Capacitor.
Reply
I have a Jandy with a century B2854
56AA40A01
I replace this motor every 2 years, the technician says the bearings go out? Should I just purchase additional motors for future replacement? The pool service, want too charge me over $500.00
Reply
Kathe, Do you know what the specs on the original motor were? If the motor was not properly matched to the original specs, it can shorten the life span of the motor.
Reply
My motor label does not match part no. with your motors, but all other info matches, except I can't read Up
Fr-y56y, type-cx, form-KJM, AMPS-SFA 8.0/16.0, Code-J, Serial -B810-14
RPM-3450, AMB-40°, VOLTS-230/115, P/N-35-5340
1031 pool pump duty mount horizontal with can't holes down
Part,-168453-24
What motor do I order?
Reply
Louis, Based on the specs, the B854 motor matches up. There are 2 different versions of this motor. The B854 (1.5HP Up rate) and the B848 (1HP Full rate). Because of the service factors, they are basically the same motor with a different label. Either one will work. Be sure to replace your shaft seal when you replace the motor.
Reply
Whit pump do you make that matches up to the Pentair 1.5 hp pump 115-208-230v / 34802? Thank you.
Reply
Hi Blake, If you are needing to replace just the motor on your Super Flo 1.5 HP Pump then the B854 is the correct replacement motor, we would also suggest the Super Flo Tune Up Kit when replacing the motor. If you are needing to replace the complete pump and motor then you will need this 1.5 HP Pentair Super Flo Pump.
Reply
Does voltage on L1 and L2 default to 120v? For 230v is there a switch. If not where do you connect 230v?
Reply
Hi. When wiring this motor for 230 volts, terminals L1 and L2 are each 115 volts.
Reply
Let me re-phrase my question. Is this motor capable of being powered by 230V? If so, what/where is the connection or is it a switch?
Reply
Hi, Ken. This motor does come factory set to be wired for 230 volts. The terminal board along with the voltage selector switch is located at the back of the motor under the cover.
Reply
Hi, I have a pump model K48K2N100, 3/4 HP, 3450 RPM, FRAME 56C, pump diameter 5 1/2", AMPS 11.0/5.6; can I replace with this one. Or else, what model do you recommend?. Thanks
Reply
Hello Alfredo, the motor that matches with part K48K2N100 is Motor, 56c Keyed Full .75 Hp (b121). To recommend what type of seals you need we would need the pump model number.
Reply
I am looking for pool pump replacement for AO Smith serial BY04-28 part 7-193631-24 Type CX FR S56J HX 60 RPM 3450 Volts 230/115 Amps SF 6.0/12.0. What model do I need?
Reply
Need replacement motor for A.O. Smith Part 0-173840-23 Serial 11607CH
Reply
Hello Hermann, the 0-173840-23 matches with Booster Pump Replacement Motor - B625. If you need seals we would need to know which type of pump you have.
Reply
Is the b2854 motor the correct replacement for an A. O. Smith 7-177216-24 with a STA-RITE model P2RA5F-182L pump.
What is the direct replacement for that STA-RITE Pump? What shaft seals would I need? Are there others seals I should replace?Thank you
Reply
replaced motor and impeller on my pool pump, motor is getting hot and shuts off, it is a new motor any ideas?
Reply
Robert, Have you checked how the motor is wired? This is a dual voltage motor and is pre-set to 230v. If you have 115v, you will need to set the motor for that voltage.
Reply
I have a B2853 par OF56AA37A01-04. 1HP, everything matches except for code L, for my Janey system, I replaced once with this Century Model. I need a replacement motor
Reply
You can replace your B2853 with a B2853
Reply
I'm replacing the motor on my Pentair pump, motor number 196239 I think A.O. Smith 1.5 HP, 56Y Frame, Up-Rate Motor (b2854, 717721624) is the correct replacement what seal kit would I need?
Reply
Hi, Joe. This is the correct replacement for Part # 196239. However, you will need to provide us with the model or name of your Pentair pump housing in order for us to locate the seal kit you will need.
Reply
Is there a salt water shaft seal available for this motor?
Reply
Hello, the shaft seal needed is determined by the model of the pump. This number can be found on the plastic pump housing. Once you have that number, you can provide it to us and we can let you know what saltwater shaft seal will work for you.
Reply
I have a 1 hp challenger motor now can I upgrade to the 1 1/2 hp , and it would fit my existing equipment?
Reply
Hi, Stephen. You can, once you've confirmed if your system can handle the additional water flow. You will also need to upgrade your impeller and diffuser to match the motor's total hp. See the Pentair / Pac Fab Challenger Part Diagram.
Reply
I need to replace motor for my PHPM1.5 jandy pool pump. Will this be ok?
Reply
Hi, Maryann. Yes, this B854 or the PL2854 motor can be used with the PHPM1.5 pump. You will also need to replace the Pump Shaft Seal and O-rings which can be found on the Jandy Plus HP 2006-Current PHPM & PHPF Parts Diagram.
Reply
Will this motor work in the place of a B849.
Reply
No, the B849 is actually a stronger motor than this model for it is a full rated and not an uprated. The full rated versions have a higher total horsepower.
Reply
currently have a 3/4 horse pump Can I use a pump with larger horse power?
Reply
Hi, Tom. You can if you're keeping the current impeller. If not and you want to also increase the water flow, you will first need to confirm if your system can handle the additional water flow. Once you've confirmed that you will need to replace the impeller, diffuser, and seal.
Reply
I need to get pump motor #168453. The pump is CFII N1 1.5 a /343234.
Do I need to replace any seals? It's salt pool.
Do you have utube for this?
Thanks, Art
Reply
I have a A.O.Smith 7-193986-24 is this the direct replacement for my pool pump
Reply
I currently have Hayward Tristar max rate self priming pump. making tremendous noise( I assume bearings). part# 7-F56AA12A04-24 AO SMITH SP3210Z1M.
IS THIS A DIRECT BOLT UP REPLACEMENT?
Reply
Yes, this is the correct direct replacement model motor to replace the model F56AA12A04.
Reply
good afternoon. Is this a replacement for an Emerson EB854, 1.5 HP connected to a Pac-Fab challenger square mount?
also, is there an energy efficient model- for a 35, 000 gal pool
Thank you
Reply
We have a pentair pump- part #7-168453-24. Is this the right part? Also, which gasket replacement pack do we need?
Reply
Hi, Kristen. This B2854 is the correct replacement for Part # 7-168453-24. I will need to know the model of the pump housing in order to locate the gaskets. If you don't have the model number, pictures of the pump housing will do.
Reply
Is this the correct replacement motor for a Pentair Model 177475 Motor? Which gasket kit will I need for a Pentair Pump Model WF-26/011773? What type of warranty does this motor come with?
Reply
Yes, the B2854 is the correct motor to replace your current 177475 installed on the Whisperflo Pump 1 1/2 HP - WF-26 You may order the Gokit32 or the Gokit32Salt shown here http://www.inyopools.com/pool_parts_pentair_purex_whisperflo.aspx?Keywords=whisperflo+parts The motor has a one year warranty from the date of purchase.
Reply
Need to replace a motor on Jandy SHPM1.5. The motor part number is 0-193993-0 and the serial number is 06912CH. Which motor is a direct replacement?
Reply
What is the difference between a full rated and up-rated Jandy Stealth pool pump 2HP single speed?
Reply
Hi. Our How To Understand True Pump Horsepower - Up Rated vs Full Rated explains the differences between these motor/pump type.
Reply
i have a PAC FAB Challenger pool pump 1 1/2 hp with a Nidec EB854 motor and i need to replace the motor
Reply
I need to replace a Century Centurion Type CX Frame Y56Y 230/115 VOLT POOL PUMP MOTOR PART # 0-193986-24, SERIAL # 29910CH. NEED YOUR PART NUMBER AND COST
Reply
This is the correct replacement motor for your model.
Reply
For the FLOPRO FHPM1.5-2 pump, is there a variable speed motor replacement that will drop in; or, if I want to get a variable speed motor, would I have to replace the whole pump?
Reply
Per the attached photo and a lot of research, I believe the B52854 is the replacement moter I need. Please confirm. Also which shaft seal kit would I need. I have a Jandy MHPM 1.5 pump? Thany you!
Good Morning- From the picture, it looks to be a different motor. It is the B2848 Full Rate motor that will be a direct replacement for you. You can find the replacement seals by following this parts breakdown for the Jandy Max HP (2006-Current) MHPM.
Reply
Is this the proper replacement pump for my Century SP3215Z1BE? Looks to be pretty close. The power is my main concern.
need century pump motor B2854, 1.5 hp, , challenger pac fab 35-5077 diffuser, and impeller don't have number, pump seal and spring coil don't have number, and seal lube...would you please send correct numbers thanks Mitch
Reply
Is this the right replacement? Pls note photos attached:
> Century - replacing now
> Pentair - original, replaced by the Century
> Whisperflo pump in use
Also:
> Is there an o-ring? Please provide part number.
> Seal plate was replaced 2 years ago and assume is still fine; please advise if you differ.
> The pump is original (2005), but seems to be working fine. Should I consider a new impeller or rebuild kit and is replacing it a simple task or a significant challenge?
Thanks!
Yes, this is the correct single speed motor replacement and we advise to replace the seals and gaskets. For this one, it is the GOKIT32 or the GOKIT32SALT for a saltwater pool. If the impeller is clearly worn or damaged then we advise to replace it but most people replace the motor, seals, and gaskets.
Reply
hi,
i would like to get the most appropriate replacement motor. i've included pictures for your review. is this 1.5 HP appropriate for my standard size pool? also, what's the warranty on the motor? Free Shipping?
Hello, thank you for providing me with those photos. You can go with the USQ1102 motor. Along with this, you will need a new shaft seal to prevent damage to your new motor. For this part, can you please provide me the number off of the label that says "DO NOT RUN DRY"?
Reply
I currently have a Pentair Challenger system with a Century 7-F56AA40A01-24 1.5 hp motor.
I'm getting a high pitched squeal from the existing motor. From looking at your site, it appears I need item .A.O. Smith 1.5 HP, 56Y Frame, Up-Rate Motor (b2854, 717721624). Will you please confirm this and provide me with the other part numbers I will need to complete the job correctly?
Thank you,
Bob
Reply
I currently have a Hayward Tristar Pump. I need to replace the motor. The motor is a Century model # B2854. The part number is 7-F56AA40A01-24. Can you tell me the correct replacement motor and seal kit. The pool is a salt water pool.
I'm looking for a replacement baring and seal kit for swimming pool salt water pump. I have attached photo of the motor for your reference. if you have any questions, please email me. Thanks.
Hello, Can you please resend the photo? The picture is in a small format and I can not zoom in to read the numbers.
Reply
Need to replace the motor and attachments and all necessary parts for replacement installation except
pipes.
Thank you
Gene
Hi Gene, We are sorry but we are unable to track down your exact pump model so we can't suggest the proper replacement shaft seal. The B123 replacement motor has been discontinued but you could go with the B124 2 HP Replacement Motor if you go this route you will need to make sure you have 230V power as your previous motor could be wired 115V/230V and the B124 can only be wired 230V. Another option and the option I would suggest would be to go with a brand new 2 HP PureLine Prime Pump this would require a little replumbing but I believe in the long run would be your best bet.
Reply
Good afternoon, I am looking for A.O. Smith Century Pool and Spa motor SP3215Z1BE, part 7-196337-20, frame Y56Y, Type CP, and would like to confirm if the part# B854 listed on your website is a replacement in kind. I attached the nameplate. Please, advise
I have an A.O. Smith century Centurion Purex Triton WFE-6 Triton whisper 1.5 hp pool pump serial number 1099 – 133 that needs to be replaced and I'm just calling to confirm that this is the appropriate replacement pump. Thank you Scott
Reply
Hi, Miritello. This B2854 is NOT the correct replacement. The B2842 motor and the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT are the parts you will need to get your pump up and running again.
Reply
best-or-better replacement motor that mates up with a pentair 340037 pool pump
Reply
looking to replace a Century centurian A.O. smith part # 7-193986-24 for a jandy pool pump
is century B2854 1-1/2 hp the proper replacement?
Reply
Hi, Jim. Yes, this B2854 motor is the correct replacement for Part # 7-193986-24.
Reply
Are the new gaskets et included or do I have to order separately? Thank you
Reply
Hi, Jim. The gaskets are not included, they will have to be purchased separately. You will need to locate the pump housing model or name.
Reply
B2854 this is the model # of the centurion pool filter model. Can you tell me the gasket info et that I will need from that? Thank you
Reply
Hi, Jim. You will need to provide us with the pump housing name or model in order to locate the seals.
Reply
I believe the housing is as follows: PlusHP Jandy pool products Model # PHPM 1.5 Serial # K07FC5286 HP 1.5 Non self priming looking for the gaskets to go with the replacement pump. Thank you
Reply
Hi, Jim. The part number for the seals are; Shaft Seal - R0445500, Backplate O-ring - R0446300, and the Diffuser Hardware - R0446500.
Reply
It seems the electrical chord has been overheated and is damaged. I was going to reuse the old one but will now need to purchase a new one. Can you advise the proper part #? Thanks again!
Reply
Hi, Jim. We only have Power Cords - PL3547 (3-Prong) or SPX1550WA1 (Twist-Lock) for 115 volt operation.
Reply
Maybe that is what I am asking for? I need the cord that gets wired to the motor with the plug at the other end so I can plug it in.doyouhsve that part? Thank you
Reply
Hi, Jim. Chose from P/N PL3547 (3-Prong) or SPX1550WA1 (Twist-Lock) for 115 volt operation.
Reply
Maybe that is what I am asking for? I need the cord that gets wired to the motor with the plug at the other end so I can plug it in.doyouhsve that part? Thank you
Reply
Seeking to purchase a : A.O. Smith 1.5 HP Square Flange 56Y Up Rate Motor - B2854
to replace my older B854 ( see photo )
what "whisper kit " - Seals / gasket kit etc will i need to order to go with it?
Thx
Chris
Hi, Chris. This B2854 or the PL2854 motor along with the Pentair Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT are the parts you will need.
Reply
I have a 340039 Pentair Superflow Pump. The motor is a 177475 model number with the square flange. The motor is a 1.5 hp. Which new motor model number do I need to replace my motor?
Reply
Hi, i have this motor now from your store maybe 3 yrs ago, its been working great - Can you tell me what variable speed motor to get to upgrade (to fit same pump style as this)? The pump body is jandy php2.0 (/1.5 with correct diffuser/impeller, i have both 2.0 and 1.5hp sets). And would i use 2.0, or 1.5, diffuser/impeller?
thanks
Reply
Hello - I want to double check on the replacement motor for Pentair CHII Ni 1.5A 346206....Motor model# 168453. Can you point me in the right direction for replacement and seals
The replacement single speed motor is model B854 and the seal kit is part number GOKIT5.
Reply
On the gasket kit, if I am purchasing a Square flange Motor, do I need to purchase a different square gasket? The GoKIT5 mentioned no square gasket - but I am unsure if I need it or not.
Reply
Hi Andy, The Challenger tune-up kit does not include the square gaskets, however, we are showing that square diffuser gasket and square housing gasket are used on the Medium Head Challenger Pumps and the part # from your photos CHIIN11.5A indicate that you have a High Head /High-Pressure Challenger Pump which does not require any square gaskets. Based off of this information you should get everything you need within the tune up kit.
Reply
thank you
Reply
Hello - on the GOKIT5 - if I have purchased a B2854 motor and this is the seal kit, do I need to purchase square gaskets?
thx
a
Reply
Hello,Thank you for contacting Inyo Pools. The gaskets needed for the motor installation depend on the model number on your plastic pump housing. If you could please send me a photo of this, I can let you know exactly what you need.
Reply
Hello - I want to double check on the replacement motor for A O smith Mod # K48M2N110C1, 1.5HP, Volts 115/208-230, RPM 3450, AMPs 19.6/10.4-9.8, SF 1.47. Can you point me in the right direction for replacement and seals
Hi Bill, Thanks for the great photos those were quite helpful! This B854 motor is NOT the correct motor for you. You will need this ST1152 1.5 HP Full Rate 56J Motor along with this Hayward Super Pump Seal Kit. We have put together this Video on How to Replace a Pool Motor which you may find helpful when you tackle this project.
Reply
is this the correct motor for me based on the pics.? Do I need anything’s else
Hi Sean, Thanks for the pictures those are helpful! Yes this is the correct replacement motor for your Jandy PHPM1.5 pump. You will also need this Jandy PHPM Shaft Seal when you replace your motor. We also have this Video on How to Replace a Pool Pump Motor which you should find helpful when you tackle this project.
Reply
Hello, I have a motor B2854 and when I remove the back cover the shaft spins when pump is on but zero movement in pump area. Removed lid, turned on (just bumped it on a sec) and no movement on the front end. Is this a sheared shaft or not necessarily? Trying to see if its cost effective to replace entire unit or just parts, Thanks
Reply
Hi Rando, Could you give us the information off of the motor for your current pump like HP, Amps, Volts, SF, Frame, Model #, etc.. Also could you give us the pump make and model information, common pump names would be Pentair Whisperflo, Pentair Challenger, Jandy Stealth, etc.. To supply this information click the reply link below, also if you could send a few photos those are always helpful as well. If you send photos then take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get any of this information we can make the proper recommendation.
Reply
I need to replace my Centurion Jandy - AO Smith Pump 1.5HP Pool Pump Motor.
Part # 193986 Jandy Code FHPM1.5
Is this the correct replacement motor?
Reply
Hi Michael, Yes this is the proper replacement motor for the pump information you have provided.
Reply
Hello. Would this be the correct motor to replace my Hayward tri Star 1.5 hp y56y. 230/115 volts. 5.1/16.2 amps. Model sp3210Z1M.
Yes this would be the correct replacement single speed motor for you.
Reply
what shaft seal fits this motor thanks jay
Reply
Hi. We will need to know the model of the pump housing which is what the motor mounts to in order to locate the seals. If you do not have the housing model or name, you can provide us with pictures.
Reply
What shaft seal part # do I need for this motor?
See pic below
Hi, Michelle. The seals are specific to the pump housing, not the motor. You will need to provide us with the housing model number or name in order for us to locate the seals. You can also reply with pictures of the housing.
Reply
What shaft seal part # do I need for this motor?
See attached
Hi, Mary. We will need to know the pump housing model name or number in order to locate the seals. We're unable to use the motor info. If you do not have the pump housing model name or number, you can reply with pictures of the housing.
Reply
Hello - The name plate has fallen off of my pump so I am not certain and need help. All I have is as follows: Century Centurion Switchless motor - No switch - No Governor 2514514-001. Please let me know if this motor you are advertising would be the correct motor to purchase in order to replace my burned up motor. If so I will purchase today ASAP. If not, please let me know what motor you think I would need to purchase. Many Thanks ! Michael
Reply
Hello, Can you please send a side view picture of the entire pump? With a picture of the motor label?
Reply
Do you have a photo you could send of your pump housing and strainer body? Can you see any part numbers on those?
Reply
I have a poolpump motor Pump model no P6RA6F-206L motor#196250 what motor do I need to replace it with
Reply
hey,
Is this a good replacement for my current pump? photo attached
The B854 is not the correct motor replacement; you will need the B130 - 1 HP Round Flange 56J Full Rate EE Motor to replace your 7-193632-24.
Reply
Is this the right motor for this system? Part # is 0-193986-24. Also what seal kit do I need? Thanks
This is the correct replacement motor and please click here to be directed to the parts diagram for your pump. There is no seal kit for that model but most commonly the seals and gaskets replaced are keys 5, 13, and 15. You will need the pump housing serial number to confirm key 5.
Reply
I need a replacement motor just like this one
Reply
Can this motor be used to replace a Hayward 196337?
Is that why it comes up in the listing when I search for 196337?
I purchased a B2584 Pump that I am installing. The current pump base that I have for the old pump is higher in the back causing this pump to sit un-level. I can't find the part number for a plastic base for this pump that is level.
Reply
Hi, Gary. You will need to remove the motor spacer in order to get this motor to sit level.
Reply
I removed the rear spacer that's on the base that I have but this pump still sits on an angle. This base, even with the spacer removed, has a lower front seat and higher rear seat because the pump that was originally installed had a thicker neck at the front behind the square flange. I know I saw a flat base on a parts diagram when I was looking for the pump but can't seem to find it again.
Reply
I am replacing this exact Century B2854 motor after 7 years+ on a StaRite Super Max pump from Pentair. I need the gasket kit for this exact pump. There are several kits out there and I need the right one. Thanks.
Reply
I need to replacee the motor on my Sta Rite PHK2RA6F-103L. Could you please tell me if this is the appropriate replacement part? Thanks!
Reply
have century b2854 pump - need a new pump and kit with new o rings. it is a salt pool and has a wisperflo /Pentair pump. decal has faded - cannot read the data plate. what is the kit number?
Reply
The item you need will be the Tune Up Kit Pentair/Purex Whisperflo Saltwater - GOKIT32SALT.
Reply
I'm replacing the electric motor on a Champion Waterway 56 Frame Pool Pump. Are there any additional seals or gaskets needed to complete the replacement and if so, what would they be? Thanks!
Reply
Hi, Dan. Yes, the seals and gasket that are needed are all listed on the Waterway Champion 56-Frame Pump Parts Diagram page.
Reply
I just replace my motor and now the pump is leaking from the bottom
Reply
Hi, Gregory. You may want to recheck the installation of the pump shaft seal. Check out our How To Replace a Pool Motor Shaft Seal guide.
Reply
I rechecked the installation of the shaft seal. The pool pump now has a steady slow drip coming from the bottom. What could be the problem now?
Reply
You may want to check the plastic parts in the pump to make sure they are not warped from the heat. Also, check for any cracks, and seals that may need to be lubricated, are dirty or may not be seated correctly.
Reply
Is this the correct replacement for my motor,
And what seals if any ?
It’s a pentair 1 1/2 challenger
Reply
The seal kit for the CH series Challenger is the GOKIT5 for a chlorine pool and GOKIT5SALT for a saltwater pool but if you have the CF series then you would need to purchase the diffuser gasket part number 5002-13A with the kit.
Reply
I am looking for the correct replacement motor for my waterfall feature.
Will this motor work with my pump and what seal kit should I use?
Hi, Jon. Yes, this B2854 motor can be used as a replacement. You will also need the Pentair Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
What replacement motor works for a replacement.
Hello,Based on the pictures you have provided, this will be the motor you will need,http://www.inyopools.com/Products/03000017000395.htm?Keywords=b854
Reply
is this the right motor replacement for my current motor as shown in the pic.
Hi, Yassir. Yes, this B2854 motor is the correct replacement. You will also need the Pentair Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
Hello .. is this the right replacement for my motor
Hi, Yassir. Yes, this B2854 motor is the correct replacement. You will also need the Pentair Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
I am in dire need of some help in tracking down the correct for my A.O Smith B284 housing gasket. It looks similiar to the Pentair 357102 but there is some curvature to the bottom of the gasket as to the ones I have seen pictured. Any help i this matter is greatly appreciated....thanks in advance
Hello,
Is this motor # B2854 for a pentair whisper flo WF-4 motor # 177475
Thank you,
Reply
Hi, Tim. Yes, this B2854 motor is a suitable replacement for the Whisperflo Pump WF-4. You will also need the Pentair Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
What seal package would I need for a Pentair 1.5 HP CHII-N!-1-1/2F 34-5201 Self Priming Pump? Is this the correct pump motor?
Hi, Alan. The B2858 is the correct motor and GOKIT5 or GOKIT5SALT is the correct seal kit for your model pump.
Reply
What would be the right motor I would need to get if I wanted to go with a 1.5hp. I have a Sta-Rite Max E Pro Model #P6RA6E-205L
Based on the photo provided you would need to order the 1 HP Square Flange 56Y Up Rate Motor - PL2853
Reply
I need to replace the pool pump and wondering if this model will match the existing. Looks good to me
How long should a pump motet last. I purchased and installed this motor 16 months ago and the last couple of days it has started making very loud noise when it runs
Reply
On the average a pool motor will last approximately 3-7 years, however, other variables may affect that such as shaft seal failure, weather, resistance, insects, or even power surges. A loud noise is most commonly associated with a shaft seal failure. We recommend looking at the face of the motor to see if there is corrosion present which would be indicative of a shaft seal failure.
Reply
I have checked the front and there are no signs of corrosion. When I purchased the motor from inyopools 16 months ago I also purchased and replaced the seal.
Reply
Roberto, If the shaft seal did not fail, then the bearings did.
Reply
I need to replace motor on pentagram superflo 350097 pump. 1.5 Hp
Motor # 196239. What parts do I need
The A.O. Smith 1.5 HP Square Flange 56Y Up Rate Motor - B2854 with the Tune-Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78 If it is a salt pool add the Pump Shaft Seal Heavy Duty (Saltwater Pools) - PS-3867 with the Tune-Up Kit78. If the impeller and diffuser are 10+ years of age, it is suggested to replace those for optimum performance of the new motor.
Reply
I have a Pentair Motor #196239. Pump Model SF - N1 - 1 - 1/2A /340039. It is for a saltwater pool. Please let me know what pump/parts I need to replace.
Reply
Thanks for the quick reply. If the filter is good, will the filter fit on the new replacement, or do I need to buy pump with filter?
Thank you!
Reply
I believe that you are referring to the pump basket which that strainer pot and assembly will be used with the new motor.
Reply
Will this motor work with pool? Here’s a pic of the old one. It’s hard to read model #. Also, does pump come with gaskets and seals?
I am replacing a 1 HP pool motor on a 35 gallon fiberglass pool. the motor attaches to a Flo Pro pump which appears to have no problems. The part number for the old motor is 7-168453-24. The Serial # BT6-02. I know nothing at all about this matter and need trustworthy advice. I assume I also need gaskets or install kit?
Reply
The water flow for my water feature is too strong and the falling water makes too much noise; I would prefer a gentler flow. The B2854 motor is the correct one, but is there another that would reduce the water flow?
Reply
Hi, Elisa. In order to reduce the water flow, you can reduce the motor size along with the impeller and or diffuser based on the make and model of the pump you have.
Reply
I am looking for a replacement pump motor and seal kit for a SMF 115. Here is the data label. What part numbers do I order?
Hi, Thomas. The replacement motor is the USQ1152 - A.O. Smith 1.5 HP Square Flange 48Y Up Rate Motor.
Reply
I also will want the seal kit for when I replace the motor. Can you send me the part number for that also. SMF 115.
Reply
Thomas, The seals are all listed on the Waterway SMF Pump Parts Diagram page.
Reply
Could you tell me the model number for the closed back version of this motor as I believe this is the open back one? The motor I am replacing was a closed back one so I would be hesitant to replace with this one. Thank you!
Reply
Hello Vickie, no the Magnetek A.O. Smith 1.5 HP Square Flange 56Y Up Rate Motor - B2854 does not have a backless option.
Reply
I am attaching a picture of old pump as well as the B2854. It isn’t a problem that the B2854 isn’t entirely enclosed. The question was raised by this wording in the instructions. Thanks!
Vickie, The motor design was changed. This version will also work.
Reply
As you can see. I have an old Magnetek pump. I believe the old guy has finally had its last suck day :). Please tell me best options. I would like if possible to save the blade side and reattach a better pump, is that possible? If not what do I do?
Thank you
Hi, S Nelson. This B2854 motor can be used as a replacement. You can use the B2841V1 as an energy-efficient option.
Reply
Thank you, glad this sounds easier than I thought. You mentioned B2841v1 as more energy effiicient, all for saving money. Is this because it is 1HP or other? If so, what is difference in Kilowatts hours used between the two. I average 4 hours a day in summer, 2 hours a day winter.
Reply
I'm looking for a replacement motor for the one I currently have (see photo) but am not sure if this is the right one. This is attached to a JandyStealth Pump. Can you advise if this is the one or if I need something else? Thanks in advance.
Good day, based on the motor label information showing 7-193993-05, the A.O. Smith 1.5 HP Square Flange 56Y Up Rate Motor - B2854 would be the correct motor.
Reply
I am looking to replace a Century Centurion B2854 for my infinity edge.
I have a couple quick questions - 1) Is this motor new or rebuilt? 2) what is the warranty on the motor?
Thanks.
Reply
Hi. This motor is new and is warranted for 1 year.
Reply
I currently have the Pentair Challenger II, with a square flange. Is this motor a compatible replacement? Thank you.
Hi, Kyle. Yes, this motor is the correct replacement. You will also need the Challenger Pump (CH Series) Tune Up Kit - GOKIT5 or GOKIT5SALT.
Reply
My FloPro Jandy HP 1.5 motor is humming. Could it be the capacitors or do I need to place the motor? If it’s the motor will this model fit?
Reply
Hi, Jay. You can start by testing the capacitor using the instructions in the How to Test a Pool Pump Capacitor guide to confirm if its the culprit. If the capacitor is okay, you will have to replace the motor.
Reply
Hi there, the motor just went out in my whisper flow WFE-6 pool pump. Can you yell me which one is the correct model. It is 220 volt. Thanks
Reply
Hi, Cameron. The B2842 motor along with the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT are the parts you will need for your model pump.
Reply
My B2854 just went out. Looking to replace it. Should I replace with same model or are their better (upgraded) options? Do I need any additional parts like seal kits?
Hi, my pool pump motor is about to quit and I was wondering if this is the correct replacement for mine? Pics are attached. I also need a new impeller so could you please tell me which would be the correct one to fit to the new pump. Thanks
Hi, my motor is B2854. If replace it with the same model, what is the seal kit I should use?
If I upgrade to B2841V1, what is the seal kit I need to buy.
If I upgrade to ECM16SQU, what is the seal kit I need to buy
From the end of the motor to the wall of my house there is only about 1 inch, is there enough space to put B2841V1 or ECM16SQU, I did not find dimension data of the motor
Hi, Simon. Yes, there is enough space to use the B2841V1 or ECM16SQU. The Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT is the kit for your model pump.
Reply
Thanks for you help. I replaced my broken B2854 with the variable speed motor. Everything fits well.
Reply
Looking for a replacement motor for my pool pump. Was seeing if this is a viable replacement.
HI Can I use this to replace my Hayward Tristar Pump, SP3210Z2ME, I know it's not the dual but the single speed should work just fine. Do you think I will have any issues using this as the replacement.
Reply
Hi, Mark. This B2854 motor will work as a single speed replacement if you do not reside in the state of CA or WA. These stated prohibits single speed motors. You will also need the TriStar Pump Tune Up Kit - GOKIT81.
Reply
Thanks would this one work as well to replace the Tristan pump as a dual speed option? Century 1.5 HP Square Flange 56Y Full Rate Motor - B2858
Reply
My pool pump won’t turn on at all. There is no humming sound. The box is getting power but it seems that the timer motor is not working. Could that be the problem? I'm getting voltage to the motor,is there a reset
Hi. If the motor is getting the proper voltage 115 or 230 volts from the timer if manually switched on, then the motor is bad. The timer motor will also need to be replaced.
Reply
Can you tell me the primary difference between this pump and the B2854 and which is a better replacement for a Hayward Tristar 1.5
Hi, Mark. This B2854 is a single speed motor with a THP od 1.65. The SPX3210Z2MER is a dual speed 230 volt motor with a THO of 1.85 (high) / 0.23 (low). The SPX3210Z2MER is the correct replacement. You will also need the TriStar Pump Tune Up Kit - GOKIT81.
Reply
Can this motor replace Century motor B2842?
Reply
Pete, no the Magnetek Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is an up rate motor with a lower true horsepower than the Century 1.5 HP Square Flange 56Y Full Rate EE Motor - B2842. If you were to swap for the B2854 you would require a new impeller and possibly a diffuser to accommodate the change in power.
Reply
Please confirm this product will be an adequate replacement to my current motor (attached).
Thank you!
Hi Matt, No this is not the correct motor. You will actually need this B2853 1 HP Motor You will also need a Pentair Super Flo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Is this the correct replacement motor?
Hi, Ray. It is NOT, your options are P/N SP3215Z1BE or B2858. You will also need the TriStar Pump Tune Up Kit - GOKIT81.
Reply
Is this the correct replacement for my motor? And si there any additional items that would be needed? Thank you in advance.
Is this the correct motor for our replacement? See picture of what we currently have. Thank you
Hi, Shelly. Yes, this B2854 motor is the correct replacement.
Reply
Do you have a replacement seal and gasket set for this motor?
Reply
Shelly, You will need to provide us with the pump housing model info since the seals are not based on the motor.
Reply
This is our pump. Can you let me know what we need for the seal and gaskets so I can get them ordered? Thank you.
Reposting with more info. . .
Water coming out of bottom of pump where it connects to the housing. Going to replace the pump as it is old. . .see photos - is this the right pump? Also, my housing is a Jandy ProSeries Stealth Model SHPM1.5. What seal/gasket kit do I need? Thanks!
Hi ACTX, Yes this B2854 is the correct replacement motor for the motor in your photo. You will also need a shaft seal when you replace your motor and the Jandy SHPM1.5 has used two different shaft seals and this is determined by the serial # on the side of the pump. If your serial # is before P08FF0001 then you will need this Old Style Jandy Shaft Seal and if your Serial # is after P08FF0001 you will need this New Style Jandy Shaft Seal For example if the serial # starts with an A then that is before P08FF0001 and if your serial # starts with a R than that is after P08FF0001.
Reply
Thanks for the quick reply! I am confused as to which serial number I am checking? On the Jandy unit? It's serial number is U13FB2018.
Reply
Thanks ACTX, Based on your serial # you will need this New Style Jandy Shaft Seal
Reply
I have an AO Smith Century Centurion. The impeller is attached with a center screw. Does the screw have a standard thread or reverse thread? I didn't apply too much torque to the screw as this thought crossed my mind. I can send photos if you need them. Thanks.
Reply
Hello Peter- The impeller screw is going to be reverse threaded. They aren't necessary anymore so once you take it off you won't have to put i on your new motor.
Reply
What size capacitor goes with the Century 1.5hp motor?
Reply
So there are multiple 1.5 hp Century motors. If you can provide us with the motor model, part or catalog number then we may be able to locate the correct capacitor for you.
Reply
So in preparing to replace the seal and or motor, I separated it from the Jandy unit and trying to remove the impeller. There is a single screw (self sealing screw) that is very tight. If i understand some of the youtube videos I get it off by turning the impeller while holding the end of the motor axel with a wrench, not by using a screw driver on it?
Reply
If there is a screw at the very center of the impeller threading it to the shaft of the motor then that must be removed for the impeller to come off. Sometimes they can be stubborn. Please click here to check out a guide we created for this very task called "How To Remove Stubborn Pool Pump Impellers."
Reply
Hello. At a minimum I'm going to have to replace my B2854 Century motor. I understand the shaft seal must also be replaced at this time. My pump is a Jandy SHPM 1.0, serial L07FD4109. Based on a prior answer to another customer from you, am I correct in thinking this would be the old style Jandy shaft seal? Also, if I decided to replace the entire pump and motor with a variable speed unit, what would you recommend as a replacement for similar service? Thanks!
Reply
Hi Jack, Yes are correct in needing the old-style shaft seal. If you wanted to go with a complete new Variable speed pump then we would suggest this 1.4 HP Waterway Variable Speed Pump You will save a ton on your operational costs by going with a Variable Speed Pump.
Reply
Thanks much. Does that Waterway come with an installation manual?
Reply
Hi Jack, Yes it does and there is also an online version, which you can view here Waterway 1.4 HP Power Defender Variable Speed Pool Pump Owners Manual
Reply
One final question. If I just want to replace the B2854 motor, what models, variable speed and non-variable speed would would be more energy efficient than the B2854? Thanks!
Reply
Hi Jack, Here is the link to the Variable Speed Replacement Motor you would need and this would be our suggestion. You will save a ton on your operational costs with a variable speed. Unfortunately, there is not an energy-efficient single speed option.
Reply
OK, Thanks. The variable speed motor you referred me to has a 48Y frame however while mine has a 56Y. Does that matter? Also I saw the B2842 motor which is single speed and claims to be about a third more energy efficient. Would that work as a replacement for my B2854?
Reply
Hi Jack, No worries about using a 48Y frame motor to replace a 56Y frame motor. The 56Y frame motor has a slightly larger barrel size but a rubber spacer is included with the 48Y motor so there is no gap between the motor and motor cradle. The mounting flange is the exact same between the 48Y and 56Y motors. Actually the B2841V1 1 HP Full Rate EE Motor would be the proper Energy Efficient Replacement for your motor. The reason you would need the 1 HP is that this motor has a high service factor giving it the same true HP of 1.65 as the B2854.
Reply
OK, Thanks very much. I'm going to go with the variable speed ECM16SQU however. I posted a question concerning what additional parts/kits I would need at the ECM16SQU page. I'd like to order today so If you could take a look at that I'd appreciate it. Thanks again!
Reply
Jack, that's great about the variable speed motor I think you will really like it. You will need this Jandy Stealth Shaft Seal when replacing your motor based on your pump info. here Jandy SHPM 1.0, serial L07FD4109.
Reply
OK, thanks. So, no other parts? I already have an R0446500 kit and an R0446300 backplate O ring. Just wanted to know if I needed any other kits or seals/gaskets.
Reply
I've got an old Pentair pump / AO Smith motor driving my pool fountain that has finally given out. Unfortunately, pump label is largely illegible due to age. Can you tell from photos if this would be the right replacement motor? Thanks!
Hi Robert, This B854 motor is NOT the correct replacement motor for the motor included in your photos. You will require this B2853 1 HP Up Rate Replacement Motor You will need this Challenger Seal Kit when replacing your motor. Thanks for supplying the photos the part # of 7-168452-04 and the label showing 1.25 HP was helpful in tracking down the correct motor.
Reply
Hey Patrick - Regarding the tune up kit, is there any way to know before I tear down the pump whether I will need the square housing and diffuser gaskets rather than the round ones included in the kit? Thanks …
Reply
Hi Robert, Can you find a CH model # anywhere on the pump? Maybe it is listed on that label near the bottom of the pump housing where the basket is located? If you can supply the CH model # then we should be able to figure this out for you.
Reply
I found this label on the side of the basket - looks like there might be a CH # visible … Hopefully this helps! RG
Hi Robert, Thanks for the photo! We are showing that the CHII-N1-1A Challenger does not use the square gasket, so you should be fine with the gaskets that are included in the GOKIT5 Challenger Seal Kit
Reply
Great! Thank you again for all your help. I have seen the video to do the change as well. My only concern is that, given how I've had the motor (13 years), mounting screws and impeller might be a bit difficult to coax out. Hopefully won't be too much of a problem. Really appreciate your quick response. Thanks again!
Reply
Thanks Robert! If you run into any problems with the install let us know and we will be happy to help.
Reply
Thank you for your quick reply Patrick!
Reply
I am replacing a Pentair 3/4 HP Model 196237. I want to upgrade and replace it with the Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854. Do I need to get a new impeller or any other parts to reuse my current pump housing?
The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 ,Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78 ,Impeller, 1.0 FR/1.5 UP - 355074 ,and Diffuser, 35-5618 Pac Fab (355618) must be replaced when upgrading for the higher gallons per minute to be achieved. Please verify the filter has a GPM rating of 70-GPM or greater before upgrading, if it is not, you will run the risk of pressurizing the filter. How To Replace the Motor on Your Pool Pump http://www.inyopools.com/HowToPage/how_to_replace_the_motor_on_your_pool_pump.aspx
Reply
is there a way to get a number for a motor when the tag cant be read
Reply
Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
Unsure as to what gasket set I need for the pentair pump I have since the motor burnt up I’ll be purchasing the same to replace it a lil advice if possible ty
Hi. There is not a tune up kit available for your model pump, the seals will have to be purchase separately and they're listed on the Pentair Challenger CHII / CFII Series Parts Diagram page. The Diffuser O-ring - 355030, Housing Gasket - 355329, Pump Shaft Seal - PSR-200 (Standard) or PS-3867 (Heavy Duty).
Reply
I have a Zodiac PHPF 1.5 hp pool pump installed in 2012. My Zodiac manual is dated 2010 and shows an A O Smith/Century moter replacement as B858. Is this the correct motor replacement - see photo attached.
I have a 193986-24 so the B2854 seems to be what I have? My starter solenoid is out but the pump works (when I start by hand), what is the solenoid part number that I need?
Thanks.
Reply
The B2854 AKA B854 motor requires uses the RUN CAPACITOR, 30 MFD (5VR0303) (2444) http://www.inyopools.com/Products/07501352014035.htm The number 193986-24 is a part number for a motor, if the CAT# on your motor is not B854 or B2854 this may not be your capacitor. Please see How To Select the Right Capacitor For Your Pool Pump Motor http://www.inyopools.com/HowToPage/how-to-select-the-right-capacitor-for-your-pool-pump-motor.aspx
Reply
I replaced my old Petair motor with this one. I went from a 3/4 HP to a 1.5 HP. This new motor seems to run really hot. I can barely touch the housing once it has been running for about 15 min. Is that normal?
Reply
Yes, pool motors are designed to run at around 140 degrees so it will be very hot to the touch. Also please be sure that the impeller being used is not rated for the motor that you had prior for it may be too heavy for the newer motor and can cause issues with the it.
Reply
Thank you for the quick response. I have a standard Superflo pump housing from Pentair. Can you tell from the photos if this plastic impeller is unique to the 3/4 HP motor and not rated for the 1.5 HP new motor? If not, how would I be able to tell?
Hi Scott, Can you supply us with the pump model # it should be on the white or silver label on the Tan Pump housing which houses the basket. It looks like it is in the upper right of this photo but I can't read those #'s. Simply click the reply link below to upload those photos.
Reply
I attached two photos with numbers from the pump housing. I also added a 5 second clip of how it sounds. It appears to have a slight oscillating sound to it. Is that normal?
Hi Scott, Can you take a photo of the motor label and post that, just to make sure what you received is indeed the B2854 motor.
Reply
Can you tell me the difference between the B2858 and a B2854 models? Why is the B2858 so much more expensive?
Reply
The B2858 motor is a full rated motor and the B2854 is an uprated motor. The full rated model has about a half of a horsepower higher total horsepower than the uprated version hence the higher price.
Reply
I need to replace the motor in the photos. Can you give me the correct part number for the motor and seal kit. Thanks
Hi Mike, the correct single speed replacement motor for the motor included in your photo is the UST1152. You will also need a Hayward Max Flo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I need to replace my 1-1/2 HP 2 speed motor on my Pentair Whisperflow pool pump
Reply
Hi Robin, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
is this compatible with a pentair 011514
serial 032605905059
Reply
Existing motor is model no. CHII N1
Reply
Hi Timothy, could you send us a few photos of your motor? Please take a close up shot of the motor label. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
I am looking for the replacement for the sta-rite pool pump model P6RA6F-206L. Is this compatible?
Hi Dean, yes, this is the correct replacement motor for the motor included in your photo. You will also need a Sta-Rite Max-E-Pro seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I purchased the above pump motor to replace the old one. Does it come with new gaskets or do I have to purchase them as the "tune up kit"?
Reply
Hi Kevin, these motors do not come with the seal kits also referred to as tune-up kits. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
With this motor work with a star rite square flange
Reply
Hi Jamie, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
What pump motor would work this setup
Hi Jamie, unfortunately, the labels on the motor are not legible so we would need the part number that should be marked onto the impeller in order to confirm the motor model that you will need. Once you locate that please contact us using our live online chat feature and have this image ready as well so we can assist you.
Reply
Hi. I am looking for the correct replacement pump which one would you recommend.
Hi Dave, You will require this B854 Motor as well as this Tristar Tune-Up Kit
Reply
I need a replacement motor for this (attached photo)
Hi Carlos, the correct replacement motor for your motor in the photo is the USQ1072. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Will this model work with my current setup?
Hi Michael, the correct single speed replacement motor for your motor part number 193985 is the B853. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
pump went out on my jandy pro series. The label says century, serial 05314CH part 0-193994-06 type CX Frame Y56Y HZ 60 RPM 3450 Volts 208-230 Amps SF 9.6-8.8 Code H. What do I need to order to replace this? Thanks
Reply
Hi Susan, the correct single speed replacement motor for your motor part number 193994 is the B842. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I have a Century B2854 that I purchased in July 2017. The motor is making a high pitched sound. Could it be the bearings?
Reply
Hi Stacey, there are a few things that can cause a loud pool pump. Here is a guide that we put together called "Why Is My Pool Pump So Loud?" that may assist in pinpointing the issue.
Reply
im looking for a replacement for my sq1152 and im in california will this work?
Reply
Desmond, Unfortunately, the B854 motor is not California Title 20 compliant. You will need to purchase a variable speed motor. Please note that the 230v motor will only operate on 230v.
Reply
need to replace a magnetek 10-177450-03, 1 hp
Reply
Hi Doug, yes this is the correct single speed replacement motor for your motor. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Hi, tried to have our pool opened today and every time they turned on the pump, it flipped the breaker. Pool guy said it was motor, not entire pump most likely. Took picture and had insufficient info to research, but think this is the motor we need to replace. Can you confirm that we need this motor or not...in VA. Thanks!
Hi Michelle, yes this is the correct single speed replacement motor for your motor included in your photo. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or quickest provide them using our live online chat feature. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Looking for a replacement motor and seal kit for a flotec AT251501-01 pool pump
Reply
Hi Robert, You will need this UQC1152 Motor and this Flotec Seal Kit We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Looking to replace motor. Would this motor work for a replacement?
Yes this is the correct replacement motor for your motor included in your photo. We always suggest a seal kit when replacing your motor. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply your photos simply click the reply link below and upload your photos. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
Here is a picture of our pool pump
Hi Renee thanks for the photos! You will need this SVL56 Shaft Seal Kit
Reply
Neither motor started. Had electrician check to make sure power was getting to both motors and it is. But not with a man or the booster turnover make any noise or anything. Any suggestions?
Reply
Hello, here is a guide that we put together called "Pool Motor Troubleshooting" that may offer some guidance on this.
Reply
I am looking for a replacement, would this be a good one?
You will require this motor here 2 HP Full Rate B2843 Motor when replacing your motor you will need a seal kit. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
Will this motor work or would suggest another
Hi John, yes this is the correct replacement motor for your motor. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I’m looking for a replacement for this pump. Will this one be correct?
Hi Douglas, yes this is the correct replacement motor for your motor. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
The attached motor
Hello, yes, this is the correct single speed replacement motor for the motor included in your photo. You will also need a Pentair Whisperflo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I'm looking for a motor to replace the one that just went out at my home. The nameplate numbers are the same except that CODE and Class numbers are different. Code on my existing is F and the Class is B
Reply
Hi James, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or quickest provide them using our live online chat feature. Once we get those photos we can make the proper recommendation.
Reply
I’m trying to identify a replacement pump and all seals required to replace my century pump. In addition all bearings to rebuild old pump for a spare.
SP3210Z2ME
Part =7-K56AA23A04-05
Hp =1.5/1.9
Frame = Y56Y
Hi Nick, You will require this 1.5 HP Hayward Tri Star Replacement Motor and this Hayward Tri Star Seal Kit.
Reply
Will this replace Pentair Superflo 1.5hp See pic of label. Thanks
Hi Tony, yes, this is the correct replacement motor for the motor included in your photo. You will also need a Pentair Superflo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I am trying to identify a replacement pump motor and Mechanical pump seal. What motor and seal will I need. See pics.
The Pump Shaft Seal 3/4" PS-201 or http://www.inyopools.com/Products/07501352025519.htm or the Pump Seal 201, Extra Heavy Duty PS3868 (Saltwater Pools) - PS-3868 http://www.inyopools.com/Products/07501352048607.htm for salt or chlorine pools. The Gokits with the shaft seal and O-rings can be found on the Hayward Super Pump SP1600 & SP2600 Series parts page http://www.inyopools.com/pool_parts_pumps_hayward_super_pump.aspx?Keywords=super+pump+parts
Reply
Will this replace the HSQ1102? It keeps bringing this up when I google that part number, and it is cheaper than the HSQ1102 on your site? Thanks,
Reply
Hi Greg, yes you can use this motor to replace the HSQ1102 however will not be the same energy efficiency as the HSQ1102 or the B841. They are very close but technically the B841 is the best priced, energy-efficient replacement single-speed motor.
Reply
can i get this on almond color
Reply
The 1 HP Full Rate which is identical this 1.5 HP Up Rate Motor is available in Almond and can be found here 1 HP Full Rate Almond Replacement Motor You will require this Whisperflo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
HI. I have a Hayward SP2610x15 1.5hp pump. Will this motor replace my Century UST1152 ? Is this motor a higher efficiency model than the 1152? Thanks!
Hi Alan, No this is not the proper replacement for the Hayward Super Pump in your photos. If you want to go with the same motor then you can go with this UST1152 1.5 HP Single Speed Motor if you wanted something slightly more energy efficient (i.e. about 10%) then you can go with this UCT1152 1.5 HP Motor and if you want something ultra energy-efficient (i.e. 50%-70% savings) then go with this V-Green Variable Speed Replacement Motor Your UST1152 can be wired either 115V or 230V and the Variable Speed Motor can only be wired 230V. With any of these options you will require this Hayward Super Pump Seal Kit.
Reply
I need a replacement motor for my Challenger pool pump. The current motor is a 1.5 hp Y56Y Frame PH 1Century Part 7-196337-20. Do you have a replacement motor for me?
Reply
I need a 1.5 hp FR Y56 PH 1 115/230 volt replacement pool pump motor for my Challenger pool pump.
Thanks
I have Century motor model #7-193986-24. Will this pump work? And which seal kit do I need.?
Thank you
Richard
Yes, this motor will be a suitable single speed motor replacement for your model motor. You will also need to know the front pump housing wet end model name or number that the motor attaches to in order to cross-reference that seal kit for you.
Reply
Hector, thank you for your prompt response. The front housing is a Jandy PHPM1. 5
Reply
Hi Richard near where the model # is listed there should be a serial # we will need this to suggest the proper shaft seal. Please click the reply link to supply this info.
Reply
The serial number is not legible
The good thing is I only needed to know the first digit of the Serial #. Since it starts with a "U" you will require this New Style FHPM Shaft Seal when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
If the pool pump is model # PHPM1.5 and serial number R09FL1289 and it is connected to the same motor listed above (7-193986-24) what seal kit would I need to purchase?
Reply
Hello Connie, for the PHPM and serial number "R09" the correct shaft seal will be part number 5020-087. You can also replace the backplate o ring part number 5020-136 and the diffuser o ring part number 5020-116 since this series doesn't actually have a complete seal kit.
Reply
I have Century motor model #7-193986-24. Will this pump work? And which seal kit do I need.? The housing brand is Jandy model #PHPM1. 5
Reply
I am looking for a new pool pump. I have attached some pictures.
Thanks
L. David
Hi, Thanks for the photos! You will require this B2858 Replacement Motor and this Super Flo Seal Kit If you live in California let us know as you will require a different motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
How many GPM does this pump produce?
Reply
Hi Chris, in order to confirm your gallons per minute rating you will need to read your pump curve for your model pool pump. Here is a guide that we put together called "How To Read a Pool Pump Curve" that should assist with that.
Reply
I need a replacement motor for a US motors EB977 2 speed j65 round flange. Do you carry that specific motor?
Reply
Hi Mike we carry this B2977 Motor which is the exact same motor but it is manufactured by Century Motors and not US Motors, we have had much better success with Century. When replacing your motor you will need a seal kit. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
The pump housing is a Hayward. Would a Hayward spx1610z2mns be a better choice?
Hi Mike, Thanks for the photos! Based on your photos you have a Hayward Super II Pump and we show that the spx1610z2mns is specific to the Hayward Northstar Pump. We would suggest this 1 HP Full Rate Dual Speed Motor and this Hayward Super II Seal Kit. The reason we are suggesting the 1 HP full rate is that the True HP for the 1 HP full rate is identical to your 1.5 HP Up Rate. Here is the math showing this 1.5 HP Up Rate - 1.5 HP x 1.0 Service Factor = True HP of 1.5 THP and 1 HP Full Rate - 1 HP x 1.5 Service Factor = True HP of 1.5 THP
Reply
I need a replacement motor. 1hp 125 SF
Centurion part 8-168452-04 fr: P56Y
serial bt4-275
I have attached a picture of the faded label
Your replacement motor for model 168452 is 5231X that you can view by clicking here.
Reply
The replacement motor is only 3/4hp, My old one is 1hp. Will that be powerful enough for my pool is around 18x30
Reply
I need replacement motor Century part No. 0-196256-06 Type CX Frame Y56Y, 1.5 HP, Code H RPM 3450 Volt 208-230. If replacement ordered how long to delivr to SE Florida
Reply
Hi, I think I found the right replacement motor. Please look at the photo. My question is do I need a new seal. If so, which should I order?
Hi Bruce, yes this is the correct replacement motor for your motor included in the photo. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
My pool pump is a Pentair Model SF-N2-1A; Part # 340042, Motor # 196030. The motor in my pump is shot. Is this motor a good replacement for the existing one? I would like to increase the horse power to 1.5 if possible. If this is not an adequate replacement, would you recommend one that I may use, price and how long to deliver it? Thanks in advance.
Reply
Hi, We show you have a 1 HP Full Rate Dual Speed Motor, so if you wanted to upgrade to 1.5 HP you would need this 1.5 HP Full Rate Dual Speed Motor this Super Flo Diffuser this 1.5 HP Full Rate Super Flo Impeller and this Super Flo Seal Kit
Reply
Thanks for the reply. When adding up all that is necessary for the conversion of my unit to run 1.5 hp it comes to $536. How about if you were to sell me a motor that will run the 1 hp existing system, or recommend a new complete pump, single speed for 1.5 hp. And again thanks very much for your help.
Reply
Hi Gilberto, Currently you have a dual speed motor meaning it can run on a high and low HP setting. If you decided to go with a single-speed motor replacement then you could go with this 1 HP Super Flo Replacement Motor and this Super Flo Seal Kit and if you wanted a brand new 1.5 HP Super Flo Pump then click here for the 1.5 HP Super Flo Pump
Reply
Thanks for the reply, If I decide to go with the 1.5 HP, do I have to buy any other type of kit for the installation? How long will it take to deliver to zip code 33579, Tampa Area?
Reply
Hi, If you purchase this 1.5 HP Super Flo Pump then no additional parts are needed for installation. Delivery to your zip code is approximately 2-5 business days.
Reply
is this the right pool pump replacement for Century part 7-f56AA12A04-24
Reply
Yes this B854 Motor is the correct replacement motor for your 7-f56AA12A04-24. When replacing your motor you will need a seal kit. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
I just ordered a B854 and I am wondering if it comes with a new pump seal? If not, what is the correct seal for this pump?
Reply
These do not come with the shaft seal and in order to cross-reference the correct one, you will need to know the model name or number of the front pump wet end housing that the motor attaches to.
Reply
Can you advise me which pump motor I need. The motor is hooked up to a zodiac plus HP Model # PHPM1? 1.5 self priming
Hi, Kevin O. This B2854 can be used with the PHPM1.5 model pump.
Reply
Do I need to replace the seals?
Reply
Kevin, Yes, they're seals are listed on the Jandy PlusHP PHPM & PHPF Series Pump (2006-Current) Parts Diagram page.
Reply
Looking for a replacement pump motor, photos attached. Thanks
Hi TJ, You will require this Pentair Whisper Flo WFE-4 Replacement Motor You will also need a Pentair Whisper Flo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project. All of these items are in Stock Ready to Ship!
Reply
Hello,
I’m looking for a replacement motor for this. Could you recommend something?
Thank you.
Hi Abraham, yes this is the correct replacement motor for your motor included in your photo. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
What is the right motor for 2010 Pentair SuperFlo high performance pump? The current one i have Century HSQ165. I was told that this might not be the right one that was installed by previous owners.
Yes, this is the correct replacement motor for the motor model HSQ165 included in your photo. You will also need a Pentair Superflo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
what is the difference between the Century pool pump model's b2854 and b 2842. my pool pump is Century Centerion A.O Smith Part # 7 177451-03 and i need a exact replacement. thank you
Reply
So the B2854 is an uprated model and the B2842 is the full rated version. Please click here to view our "How To Understand True Pump Horsepower - Up Rated vs Full Rated" article.
Reply
is this motor equal to 177450-03? I need to purchase a motor.
Reply
Yes, the catalog number B854 motor is a compatible replacement for the part number 177450 motor. It just will be slightly less energy efficient by about a few amps to the direct replacement B841 motor that you can view by clicking here.
Reply
Hi,
I need to replace my Pentair Whisper Flow pump electric motor. Picture included, it says P/N 196239.
I have also seen you recommend a seals kit?
thanks for help
Hi David, this is the correct replacement motor for the motor included in your photo. You will also need a Pentair Whisperflo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Is this a replacement for Pentair motor #196250? Also do you have a kit that contains the seals and gaskets when replacing this motor?
Reply
Hi Mark, yes this is the correct replacement motor for your motor part number 196250. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I am trying to replace a pentair 1.5hp pool pump motor with 1.65 S.F. HP. is this the fit.
Reply
Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
LOOKING FOR A REPLACEMENT....PLEASE RECOMMEND FOR THE FOLLOWING MODEL 193989
Hi Shane, the direct replacement motor for your motor part number 193989 is the B982. It is recommended to also replace the seals and gaskets when replacing a motor but in order to locate those for you, we will need the front pump housing wet end model name or number to cross-reference that for you. You can also upload images of that housing in a reply here if need be.
Reply
I have the Pentair Sta-Rite Supermax High Performance pump that needs the motor replaced. I currently have the 1HP motor and would like to get a 1.5 HP motor. Which is the correct one(s) to choose from? TY
Hi Scott, the 1.5 horsepower replacement single-speed motor will be the model B854 however it is not always recommended to go up in horsepower as it may be too much for your system. One fail-safe is to go with a variable speed so you can just adjust the RPM's and not have to worry. If you do that the variable speed motor is the ECM16SQU. Here is a guide that we put together that may also assist called "How to Size a Pool Pump for Your In-Ground Pool"
Reply
Sanity check and advice. I need to replace the motor as shown in the picture. Your system has several options from Magnatek, AO Smith, and Pureline. Which one is the best replacement?
Details:
Part: 7-F56AA12A04-24
Century
Hi Phil, yes this is the correct replacement motor for your motor included in the photo. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Is this a replacement for 193824?
Hello, the correct single speed replacement motor for your motor part number 193824 is the BN50V1. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
is this motor equal to part 7-184949-22? I need to buy a motor
Reply
Hi Pinakin, the correct single speed replacement motor for your motor part number 184949 is the 5223X. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Do you have this pump in stock and how long does it take to ship to California. 1081 pool motor model K63cxepm-4759
Reply
Hi Melanie, unfortunately, California title 20 doe not allow single speed motors to be shipped to the state. We would recommend the variable speed motor model ECM16SQU. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I need to replace "US Motors Cat No E6854 Model K63CXEAP-5221"
Will this Century Pump be compatible?
Reply
Hi Max, yes this is the correct single speed replacement motor for your motor model EB854. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Will this replace a Pentair Challenger 1.5 HP pump?
Reply
Hi Jay, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. Also of the pump housing model label as well. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
How many gallons per hour will this pump do? Also how many will the 2 h,p, do?
Reply
Hello, so there are multiple variables to consider when calculating gallons per minute ratings. Here is a guide that we put together called "How To Read a Pool Pump Curve" that should assist.
Reply
Does this replace the Pentair CFII N1 1.5A/343234 motor
Reply
Is this motor a compatible replacement for the one in this picture?
Hi Kevin, yes this is the correct replacement motor for your motor catalog number B854. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
when will this motor ship if I order today
Reply
Hello, this motor is in stock with an approximate lead time of 3 business days. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
What is the GPH of B2854?
Reply
Hi Kaitlin, so there is a number of variables needed to calculate the gallons per minute rating. Here is a guide that we put together called "How To Read a Pool Pump Curve" that may help.
Reply
I have a pool motor Centurion for PAC-FAB 7-168453-24
Model B2854 of Century will work?
Reply
Will this work with a 1.5hp superflo pump
Reply
Hi David, could you send us a photo of the main motor label? To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
Hi I am trying to find an impeller and diffuser for my 1.5 HP Y56Y frame motor by Century -Centurion. Can you help me finding the right parts?
Hi Kris, for us to suggest the proper parts could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the parts.
Reply
Have a two speed pool motor that needs to be replaced
AO Smith Century part number7-181093-03 How much?
Reply
Hi David, correct dual speed replacement motor for your motor part number 181093 is the 5387X. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I am looking for a replacement motor for an 18 year old Centaurion PAC FAB 7 - 168453 - 24 pool pump. The bearings are bad and the pump screeches. The frame is a Y56Y with 3450 rpm, 8.0/16.0 amps, 230/115 volts and 1.5 hp.It has a square flange.
Is this the correct replacement motor for this pump? Also, do I have to replace the seals on the impeller when I reassemble the pump? Which seals or other supplies will I need to complete this repair?
Yes, the correct replacement motor for your 7-168453-24 Century Centurion is the Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854. The gaskets are matched to the pump housing and not the motor. What is the model number or make and model of the pump housing?
Reply
the label on the front of the pump is PINNACLE PAC-FAB 1-21-B00 34-2356 does that help identify the pump head?
I think I have B2854 motor on my Jandy Hp Plus pump.... Is there an equivalent variable sped motor that I can purchase? and if you can tell me what seal plate I will need to purchase.
Hello Krupal, The V-Green 1.65 HP Square Flange 48Y Variable Speed Motor - ECM16SQU you purchased is the correct motor for your Plus HP. Also, I'm not sure if you meant shaft seal instead of seal plate, but the shaft seal you will need based on your seal number starting with "K" is the Pump Shaft Seal OEM 3/4" - R0445500. If you purchase the seal plate you will not need to purchase the shaft seal, the seal plate is the Backplate Kit - R0445200. I will send you a quote for both.
Reply
What motor and seal kit do I need to replace this pentair motor , thanks .
Do you have a replacement for this?
Hi Bill, Yes we do carry your replacement motor, and the correct replacement motor for your pump is this B2982 Pool Motor. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Here is another pic of the motor. When I click on your replacements it is a 1Hp. Should it be a 1.5hp? Should have included this pic also. Thx
Thanks Bill these are the exact photos we needed! You will require this Jandy Stealth Shaft Seal Kit We have suggested the 1 HP Full Rate Replacement motor which is identical to your 1.5 Up Rate Motor. The math works as follows 1 HP Full Rate 1 HP x 1.65 Service Factor = 1.65 True HP and 1.5 HP Up Rate 1.5 HP x 1.10 Service Factor = 1.65 True HP. So you will need this motor here B2982 Pool Motor
Reply
Let me know what for the seal kit. Thx
I am looking to replace a 13 year old Century 1.5 hp pool pump motor - p/n 196239 for a Pentair pool pump p/n 340039.
I believe this will work but wanted to be sure.
Thank you
Reply
Hi Ron, yes, this is the correct replacement motor for your motor part number 196239. You will also need a Pentair Superrflo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I am looking for the cost of a new pump motor.
Thank you for the information on your motor. To better assist you, we will also need the make and model of your pump. This information is typically listed on a label on the housing area, opposite the motor. Once we have this information, we can better answer your questions/concerns. Please let us know if you need help locating this information on your pump.
Reply
Hello I need to replace this ,what you recommend?and I need to replace the impeller and the diffuser too?
I need to replace this motor pump, is b 2854 the right choice, and what seal kit I need for the pump
Hi Daniel, ye this is a correct replacement single speed motor for your motor part number 193986. There is no seal kit per se for your Jandy PHPM series pool pump however the most commonly replaced seals and gaskets are part numbers 5020-086, 5020-136, and 5020-116.
Reply
I'm about to replace my B2854 motor and just found out something I didn't know...that it's a up-rated motor. I don't know what that means and I'm wondering if I should go to a full-rated 1.5 hp motor for better performance. Can you explain the difference and what you would recommend?
Thanks!
Gary
Reply
Hi Gary, this is the correct single speed replacement motor for your motor model B2854. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Can I purchase the square flange for this motor separately?
Reply
Hi I have a B-849 motor century centurion 1.5hp y56y frame with a maxi glass pump here are some pics. What do you reccomend replacing it with and the go kit that goes with it
Hello Danny, The replacement motor would be the B849 and the correct replacement tune-up kit would be the Tune Up Kit Sta-Rite P4E & P4EA Max-E-Glas II / DuraGlas II - GOKIT38 based on this information.
Reply
I have a 2hp spa pump that I need to replace. Would there be a problem replacing it with a 1.5 hp pump. The part number that the B2854 is replacing is identical.
Hello, the correct replacement motor for your motor part number 17746 is the B859. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or use our live online chat feature through our web page. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I which motor and seal do I need to replace this motor?
Hi, the correct single speed replacement motor for your motor in the photo is catalog number B849. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or quickest using our live online chat feature. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I need to replace a Century O-193986-24 (can't read CAT Number). Do you carry a direct replacement (B2854?). Will your B2858 work? If so, any advantages or disadvantages. Thanks, Mike
Reply
Hi Mike, yes this B854 is the correct replacement motor for your motor part number 193986. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or quickest provide them using our live online chat feature. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I need to replace a wf-26 motor,P/n 011773,1 1/2 hp
Reply
Which motor do I need to replace this one? Will insert photo of the sticker on our current motor.
Order Number: 1152148 I ordered a replacement B854 and seal kit...I have not been able to remove the impeller from the motor. The screw is stuck and there is not enough leverage to turn the screw or by grabbing the impeller. Are there replacement parts that I have to buy to be able to install the new motor? It looks like I will need the motor mount plate, impeller, and whatever is under the impeller that cannot be seen. I have attached 2 photos
Hi Dean, most often the motor and seal kit are all that is replaced however if you have to break the impeller off then you may need a new one. Here is a guide that we put together called "How To Remove Stubborn Pool Pump Impellers" that may assist with that without needing to break it off.
Reply
Based on the image provided, what pump would be a suitable replacement. Thanks
Hi Bob, the correct replacement motor for your motor included in the photo is the ST1102. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or quickest using our live online chat feature. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I need to replace my pool pump motor. Here is a pic of the motor. I need help selecting a replacement.
Hi Sam, yes this is the correct replacement motor for your motor included in the photo. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or quickest using our live online chat feature. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Wide shots
Hi Sam, the seal kit for your pump in a chlorine pool is the GOKIT32 and in a saltwater pool is the GOKIT32SALT.
Reply
I am trying to replace a StatRite pump motor, motor # is K48M2PA 105. Will your Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 work?
Reply
Your K48M2PA105 motor is a full rate model, which means you would need the Century 1.5 HP Square Flange 48Y Full Rate Motor - SQ1152.
Reply
Will this fit or the Sta-Rite Supermax form 2017?
Reply
Yes, this would fit all Sta-Rite Supermax pumps that have a 1.5hp uprated motor. The 1.5HP uprated motor has a service factor of 1.1. That rating will be on the motor specification label.
Reply
Hello,
I need to order this replacement motor, as mine is no longer working. What seal kit or other products should I be ordering to successfully replace the motor myself?
Best - Jimmy
The correct replacement motor for your motor model (B2854) is the Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854.This is your parts diagram: Pentair / Pac Fab Challenger CHII / CFII SeriesThere are two versions of gasket kits that are compatible with Challenger, one for the High Head and one for the Medium head. If you can see your pump's model number, the CF models need the GOKIT73, the CH models use the GOKIT5 or the GOKIT5SALTIf you just want the shaft seal, instead of the whole kit you would need the Shaft Seal or the Heavy Duty Shaft Seal (For Saltwater Pools)
Reply
Is this the correct motor for my pool pump? It appears that it is. Also, what other seals or gaskets should I use when replacing the motor?
Good Morning
I am looking at replacing the motor for Pentair WF-26. Assuming the right motor for replacement is B2854.. but just wanted to confirm.
Appreciate your help
I am looking for a replacement motor for the attached photo. This motor fairly suddenly became very loud but continues to have good suction. Disassembled wet side to look for blockage in impeller. Still loud. I was just going to replace but if you have any other ideas please let me know. I have a Star Rite E-Glass system. Thanks-
Hi, the correct replacement motor for your motor will be this QC1072 Replacement Motor. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit. We do have this motor ready to ship. Please note if you live in California you may need a variable speed replacement motor to comply with state laws.
Reply
Is this the correct motor for Hayward Tristar SP3210EE pump? Original motor was replaced by Century B2841V1 a few years ago and bearings are getting loud again. The B28141V1 is 1.0 HP frame 56Y. Original Hayward motor I believe was SP3210Z.
Reply
Yes, this is the correct replacement motor for your Hayward Tristar SP3210EE pump. You will also need a Hayward Tri Star Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Can you tell me what seal kit goes with this motor? Also, can you tell me what impeller? Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 Thx Mike
Reply
The seal kit will depend on the make and model of the pump side. The B2854 Century motor can be used on several pumps. If you are unsure of the make and model, send us an image of the complete pump.
Reply
Here are the photos. Looking for motor, impeller, seal kit and diffuser please. Thx, Mike
Hi Mike, Thanks for the photos! We are showing that the P2RA5C pump is a 1/2 HP pump and the B854 motor you are enquiring about is a 1-1/2 HP motor. So you would have 2 options. Option 1 is to stay with the 1/2 HP Motor and if you went this route you would need the following items 1/2 HP Pool Pump Motor, 1/2 HP Impeller, and DuraGlas Seal Kit. If you wanted to go up to the 1-1/2 HP then you would need these items 1-1/2 HP Pool Pump Motor, 1-1/2 HP Impeller, 1-1/2 HP Diffuser and DuraGlas Seal Kit
Reply
Hi I have a Hayward sp3210x15. It has an SP3210zM motor on it now. It is no longer working. Is this the correct replacement? Do you have the impeller gaskets as well as the new seal kit too?
Sincerely,
Chris
Reply
This is the correct pool pump motor (B854) for the SP3210X15Here is the complete parts breakdown for the Hayward Tristar. Hayward TriStar SP3200X Series Pump
Reply
I have a model no. P6RA6F-206L - Sta-Rite Max-E-Pro Pool Pumps. Will this fit?
Reply
Here is a link to the Parts breakdown for the Sta-Rite Max-E-Pro PumpI am showing the replacement pump motor you need is the USQ1152
Reply
Hi. Can you tell me if this pump motor would be a replacement for the attached? And if not please tell me one that will. Also, any additional parts that will be needed,
Thanks
Hello Joe. The Magnetek Century Motor B2854 is the correct motor replacement. When replacing a motor it is always advisable to replace the shaft seal and rubber gaskets. Based on the pictures provided, it appears this is a Pentair WhisperFlo pump. If this is correct, the appropriate Tune Up Kit is the GOKIT32. Please verify the pump model prior to ordering GOKIT32. Tune Up Kit Pentair/Purex Whisperflo - GOKIT32
Reply
Is this the correct replacement?
Hi Katie, No this is NOT the correct replacement motor for your motor, you will actually need this B2853 1 HP Replacement Pool Motor When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Thank you! Here is the complete pump...
Can I use this to replace a USQ1202? 1202 looks too big for the mount.
Hi Paul, We would suggest the USQ1202 Replacement Motor as it will be the exact same motor as you currently have. You will also require this Sta-Rite Max E Pro Seal Kit when replacing your motor.
Reply
Can you tell me if this product is the correct replacement for the attached pump? And, should we purchase anything with the pump? Finally, if it ships today or tomorrow, do you know approximately how many days it takes to be delivered (Hammond, LA)?
Hi Kim Yes, this is the correct replacement motor for the motor included in your photo. You will also need a Pentair Challenger Seal Kit when you replace your motor. Please allow 3-5 business days for delivery after placing your order. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Would this be compatible with mine?
Here is a link to the correct recommended Pool Pump MotorCentury 1.0 HP Square Flange 56Y Dual Speed Full Rate Motor - B2982
Reply
I have a century 1.5 hp square flange 56Y frame B2854 motor with a cf11-n1 pump (pentair?) I notice your indicate the ch model has a special seal for salt water.. Is there a special seal for the cf unit for salt water as well??.
Also when replacing the century 1.5 motor(it has a noisy bearing now) is their a model pump that is inherently more quite than the one I have now?
Hi Clarence, In general the newer motors are quieter than the older motors so I believe this motor will be quieter than your old motor. Here is a link the Salt Friendly Shaft Seal for Challenger Pool Pumps
Reply
I have a Jandy Pro Series Plus HP model # PHPM1.5.
It has a Century Centurion motor CX Y56Y PH 1, 3450rpm, 60 hz, 230/115, CONT, DP, KJM, rated 1.50 x 1.10 = 1.65 total HP.
I need a new motor and started capacitor. Also - is there a higher power option available or more energy efficient one? Thank you in advanced!
Reply
Hi Mike, The most energy-efficient option would be this 1.5 HP Variable Speed Motor Replacement. You will also need this Jandy Plus HP Shaft seal when replacing your motor. If you wanted to stay with the same standard efficiency motor you currently have then you would need this B2854 Motor listed on this page. You will save a ton on your operational costs by upgrading to a Variable Speed Motor normally 50%-70%. Here is an article we wrote on the Energy Savings of a Single Speed Pool Pump Vs. a Variable Speed Pool Pump.
Reply
Would this be a suitable replacement for my motor?
Hi Anthony, No this is not the correct replacement motor. You will need this SQ1152 Replacement Motor
Reply
Hello, I currently have a waterway pump SMF-110 motor mod C48AB45A79, and I would like to know if I can upgrade the current motor /chassis with this item “Century 1.5 HP Square Flange 56Y Up Rate Motor”. If feasible, What other part numbers I should buy for (example, sealer, impeller)?. the reason for the upgrade is because the pump loses the prime when I adjust the suction pressure with the front valves to make works the vacuum/cleaner. it seems to be there is no air leak in the suction pipes.
Reply
Hi Randy, Yes you can upgrade your pump to a 1.5 HP motor and this B854 1.5 HP Motor would be the correct replacement motor. You will also need to replace the following parts - Waterway SMF Shaft Seal and Waterway SMF 1.5 HP Impeller. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Would this motor be the correct replacement for the one I have now ? And how long does shipping take ?
I am showing the correct replacement for your HST110 is the UST1102. Here is the link to that motor...Century 1.0 HP Round Flange 56J Up Rate Motor - UST1102Shipping this time of year will take 2-4 business days. We make pump motors our priority.
Reply
I need to replace my Pentair Whisper flow motor (355024S). I will also need the new seals and gaskets.
Will the B2854 be a direct replacement?
Reply
No, this is not the correct replacement motor for your 355024S. You will actually need this B2858 Full Rate 1.5 HP Motor You will also need a Pentair Whisperflo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I have a Century pool Pump motor (Part 7-F56AA12A04-24) that seems to be out assuming its not the start capacitor that I will change tomorrow. I think this would be the right motor for change out, Correct? Also what other parts might I need to do this?
Last I might be interested in changing over to a variable speed motor. What would you guys recommendation on that might be? I'm not sure it would be a big savings for me since my pool is rather small and I only have a suction type sweeper.
Reply
Hello Steven. The Magnetek Century model B2854 is the correct replacement for your current motor. The compatible Variable Speed model would be the ECM16SQU. A variable-speed motor utilizes less electricity than a single-speed motor because it operates at reduced motor RPMs - using less electricity, slowing circulation thus providing improved water filtering as well. The programming flexibility of the Variable Speed Motor provides the flexibility to tailor the pump's performance to the water quality needs of the pool. When replacing the motor it is recommended that the motor shaft seal, seal plate gasket, and diffuser o-ring also be replaced. These parts are specific to the pump manufacturer/model and not the motor model. More information would be helpful to determine these parts. V-Green 1.65 HP Square Flange 48Y Variable Speed Motor - ECM16SQU
Reply
Thanks for your reply.
Would you also suggest:
1) A compatible IMPELLER for the "Magnetek Century model B2854".
2) Unit price
3) If you have a installation service (Kenmore, WA 98028)?
Reply
Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
will this motor replace the MOD K48M2N110
Reply
I am showing the correct replacement for the K48M2N110 pump motor as the...Century 1.5 HP Round Flange 56J Full Rate Motor - ST1152
Reply
Which pump do I need?
Hello Andrew. The Magnetek Century 1.5HP motor model B2854 is the correct motor replacement. It is recommended that the motor shaft seal, seal plate o-ring, and diffuser o-ring be replaced at the same time. The GOKIT78 contains these parts. Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78
Reply
I am trying to replace my motor and get a tune-up kit to complete it. My Motor is for JANDY PHPM1.5 with a Century / AP Smith 1/5 HP with part #: O-193986-24 (Y56Y)77 is NOT the Jandy PHPM 1.5HP
Pretty sure the motor replacement is the B2854 / is the tuneup kit the GOKIT77?
Thanks in advance,
Pat
Hello Patrick. Yes, the Century Motors 1.5HP motor model B2854 is the direct replacement for your current Century motor. The GOKIT77 is NOT the correct tune-up kit for your Jandy PHPM 1.5HP pump, that kit contains parts for the Jandy pump models JHP/JHPU. The Jandy Kit R0445303 contains the seals, o-rings required plus a replacement impeller and diffuser. There are no GOKIT prepackaged parts for the Jandy PHPM pump series. Impeller, 1 Hp Full, 1-1/2 Hp Uprate - R0445303 Please view the attached exploded parts diagram for the Jandy PHPM model pump. Jandy PlusHP PHPM & PHPF Series Pump (2006-Current)
Reply
Is this the right replacement part for this motor (see pic)?
Hello Bart. Yes, the Magnetek Century 1.5HP motor B2854 is the correct replacement motor for your Pentair SuperFlo Pump. It is recommended that the motor shaft seal, o-rings, and gaskets be replaced at the same time. The GOKIT78 contains the necessary parts to complete this project. Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78
Reply
this the right motor to replace this? Looks like it is...
Hi Joe. The picture you provided identifies your current motor as a 1 HP Up Rate Square Flange Model 196249. The direct replacement motor is the Magnetek Century motor 1 HP Up Rate Square Flange Model B2853. It is recommended that the motor shaft seal, o-rings, and gasket be replaced at the same time. The GOKIT78 contains the necessary parts to complete this project. Century 1.0 HP Square Flange 56Y Up Rate Motor - B2853 Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78
Reply
Is this the correct replacement motor for my pool. Photo attached.
Yes, the B854 is a replacement pump motor for the Pentair SuperFlo 1.5HP. We also recommend using a seal kit. Here is the link to the SuperFlo pump kit...Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78
Reply
Hello would this pump motor work for me? See pic of faceplate! TYIA!
Hi Tracy,I am showing the proper replacement for your 7-177475-20 pool pump motor as the...Century 1.0 HP Square Flange 56Y Full Rate Motor - B2848
Reply
Will this fit a wf-26
Hi Zachary Yes, this is the correct replacement motor for the motor included in your photo. You will also need a Pentair Whisperflo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Would this pump motor work for my current pump?
Hi, yes this is the correct replacement motor for your motor. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
See pics attachéd
Tracy thanks for the photos! You will require this Pentair Whisperflo Seal Kit along with the motor.
Reply
See pic of pump and Fitler
Is this the correct motor replacement for my Jandy Stealth pump housing? If so, what seal and gasket kit will I need?
Hello Dirk. The Magnetek Century 1.5HP Up Rate Motor model B2854 is the correct motor replacement for your Jandy Stealth model SHPM. It is recommended that the motor shaft seal, seal plate gasket, and diffuser O-ring be replaced as well. Attached please find information regarding these replacement parts. Jandy Pump Shaft Seal 5/8" - R0479400 Backplate O-Ring, Generic - R0446300 9-1/2" ID, 3/16" Cross Section O-521 Diffuser O-ring - R0622000
Reply
can you please tell me the correct replacement pump for the one in the picture?
Hello Peter. The correct replacement for the Century Motors Dual Speed 1.5HP motor model B977 is the Century Motors Dual Speed 1.5HP motor model B2977. Century 1.5 HP Round Flange 56J Dual Speed Full Rate Motor - B2977
Reply
The bearings in my existing motor are going bad and my pump sounds like an airplane. Is this the correct replacement pump and are there any other seals or gaskets that you recommend changing while swapping the motor?
Hello. The Magnetek Century 1.5HP Square Flange 56Y Up Rate Motor model B2854 is the compatible replacement motor for your Century Centurion motor model 193986. It is recommended that the motor shaft seal, seal plate gasket, and diffuser O-ring be replaced at the same time. These items are specific to the manufacturer/model of the pump, and not the motor. Please provide Pool Pump manufacturer/model information and a recommendation can be made.
Reply
I have a pentair whisperflo WSE-6 with a 1.5hp motor that has gone bad. Is this an appropriate motor to replace with? 15,000-18,000 gallon pool attached to and FNS 48 DE Filter. Attached is the pump and motor information.
Hi Matt, This B2842 Whisperflo Energy Efficient Motor is the correct replacement motor for the motor included in your photo. You will also need a Pentair Whisperflo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Is this the right motor for my pump? I'm just getting a sound like it is seized up. Thanks.
AO Smith Part No. O-193986-24
Frame 56Y
1.5 HP
Yes, this is the correct replacement motor for the motor included in your photo. You will also need a Jandy FHPM Shaft Seal a Jandy Flo Pro Back Plate O-Ring and a Tube of Pool O-Ring Lubricant for the O-Ring. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Pump has stopped working. Looking for a replacement motor for Jandy phpm 1.5hp. See pictures of old pump. Thank you.
The B854 motor would be the correct replacement for your Jandy PHPM1.5 pump.
Reply
It is an old jacuzzi magnum series pump. Motor is not working. Is this the right motor.
Hello Jim. The compatible motor replacement is either the Century Motors 1.5 HP Up Rate Motor model UST1152 or the Century Motors 1.0 HP Full Rate motor model ST1102. It is recommended that the motor shaft seal, seal plate gasket, and diffuser be replaced at the same time. The GOKIT14 contains the parts required to complete this project. Tune Up Kit Carvin/Jacuzzi Magnum Series - GOKIT14 Century 1.5 HP Round Flange 56J Up Rate Motor - UST1152 Century 1.0 HP Round Flange 56J Full Rate Motor - ST1102 Attached please find an exploded parts diagram for the Jacuzzi Magnum pump. Jacuzzi Magnum
Reply
Is this a replacement for a Pentair whisperflo 1.5 hp?
Reply
Hello Dale. Century Motors 1.5 HP Up Rate Motor model B2854 is compatible with the Pentair Whisperflo models WFE-26 and WF-26. Century Motors 1.5 Full Rate Motor model B2842 is compatible with the Pentair Whisperflo models WFE-6 and WF-6. A check of the pump housing label will identify which Pentair Whisperflo model you have. It is recommended that the motor shaft seal, seal plate gasket, and diffuser o-ring be replaced at the same time. The GOKIT32 contains all the parts to complete this project. Tune Up Kit Pentair/Purex Whisperflo - GOKIT32 Century 1.5 HP Square Flange 56Y Full Rate EE Motor - B2842
Reply
Would this be a replacement for Pentair motor 177475?
I am showing the proper replacement for your 177475 on your 340039 Pentair Pump to be the B848. Here is the link...Century 1.0 HP Square Flange 56Y Full Rate Motor - B2848
Reply
Can this motor replace a B2841V1 for a Pentair Superflo?
Reply
Hi Jim, Yes this motor will replace a B2841V1 1 HP Full Rate motor as the total HP of this 1.5 HP Up Rate Motor is identical to the 1 HP Full Rate. You will also require this Pentair SuperFlo Seal kit when replacing your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Hello -- I am replacing a motor on a in ground pool pump model: SF-N1-1-1/2A/340039; HP 1.65. Please advise.
Reply
Yes, this is the correct replacement motor for the motor included in your photo. You will also need a Pentair Super Flo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
What motor pump do you recommend for replacement for SuperFlo 1.5 hp ? Please attached picture. It says Part # 177475-20. Thanks.
Hello Jamie. The Magnetek Century 1.5 HP Up Rate Motor model B2854 is comparable to your motor 177475-20. It is recommended that the motor shaft seal, seal plate o-ring, and diffuser o-ring be replaced at the same time. The GOKIT78 contains the recommended parts to complete this project. Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78
Reply
Recommended bearings for Century B2853/2854. Thanks for any feedback
Reply
Attached please find 2 brief tutorials describing the process. How To Replace the Bearings How To Replace the Bearings - Part II The front bearing is 5270-31 Bearing, 203 (Single) - 62032RS The rear bearing is 5270-31 Bearing, 203 (Single) - 62032RS Replacing the motor is the other option. Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 Reply
Reply
I am replacing a pentair square flange 1.5 hp model# 355024S.
Can I replace it with your A.O. Smith Century B2854 Up-Rate 1.5HP Square Flange Pool/Spa Replacement Motor?
Reply
Hello Cameron. The Magnetek Century Motors 1.5 HP Up Rate Motor B2854 is a compatible replacement for the Pentair 1.0 Full Rate Motor 355022S.
Reply
My Jets circuit breaker is tripling i was told that my motor is bad what motor do you recommend i get to fix my problem?
Hello Elbasan, The Century Motors 2.0 HP Full Rate Motor model SQ1202 is the compatible replacement for the motor model K48N2PA105. Century 2.0 HP Square Flange 48Y Full Rate Motor - SQ1202 It is recommended that the motor shaft seal, seal plate gasket, and diffuser 0o-ring be replaced concurrent with the new motor. The GOKIT79 contains the necessary parts to complete this project. Tune Up Kit Sta-Rite Max-E-Pro (Pre February 2015) - GOKIT79 Attached please find an exploded parts diagram for the Sta-Rite Max-E-Pro for reference.
Reply
I have a Jandy PlusHp Pump Model PHPM1.5 Will this motor work as a replacement?
Hello. The Magnetek Century 1.5 HP Up Rate Motor model B2854 is a compatible replacement for the Jandy Plus HP model PHPM 1.5. It is recommended that the motor shaft seal, backplate o-ring, and diffuser o-ring be replaced concurrent with the motor. Jandy Pump Shaft Seal 5/8" - R0479400 Backplate O-Ring, Generic - R0446300 9-1/2" ID, 3/16" Cross Section O-521 Diffuser/Impeller Hardware - R0446500 Attached please find an exploded parts diagram for the Jandy Plus HP model PHPM Series Pool Pump. Jandy PlusHP PHPM
Reply
I'm planning to order the above motor for my Pentair Whisperflo 1.5HP pump (original motor #071315)
also the GoKit 32 SALT since pool is saltwater
Do I also need the Inyo Image
Pump Shaft Seal Heavy Duty (Saltwater Pools) - PS-3867 ??
also, about how long is the shipping to NY? thanks for the help!
Reply
Hello Jill. The Century Motors 1.5 HP Full Rate Motor model B2842 is the direct replacement for the Pentair Whisperflo 1.5 HP motor model 071315. Century 1.5 HP Square Flange 56Y Full Rate EE Motor - B2842 The GOKIT32SALT contains the necessary parts to complete this repair. Tune Up Kit Pentair/Purex Whisperflo Saltwater - GOKIT32SALT No additional shaft seal needs to be purchased. Attached please find the INYO Pools Shipping Policy which will describe shipping options to New York State. Shipping Policy
Reply
Is this a replacement for the Starite 1 1/12 HP? we have salt water if that makes any difference. Thanks.
Reply
It could potentially be installed on a pump manufactured by StaRite. We will need the StaRite pump model name or number to suggest the correct pump seal kit for a salt pool. To identify the motor you may check the label for the motor model, part, or CAT#. We offer How To Choose The Right Replacement Pool Pump Motor https://www.inyopools.com/HowToPage/how_to_choose_the_right_replacement_pool_pump_motor.aspx and How To Find The Correct Pool Pump Shaft Seal https://www.inyopools.com/blog/how-to-find-the-correct-pool-pump-shaft-seal/
Reply
Looking to see if this is compatible with my pump and if any additional parts are needed with a salt water system.
Hello Lisa. The Century Motor 1.5 HP Up Rate Motor model B2854 is a compatible replacement for your Jandy Stealth Pool Pump model SHPM. It is recommended that the motor shaft seal and backplate o-ring be replaced concurrent with the new motor. Jandy Pump Shaft Seal 5/8" - R0479400 Backplate O-Ring
Reply
Will this be a replacement pump for my Pentair Whisper Flow? Also any seals or gaskets, O-rings required?
Pictures attached.
Thank you for contacting Inyo Pools, Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 Tune Up Kit Pentair/Purex Whisperflo - GOKIT32
Reply
Will the B-854 motor replace a Jandy Centurion Motor on a FHPM 1.5 pump
Reply
Hi Brian, it will as long as you have the single-speed motor. You would want the B2983 if you have the 2-speed pump. Be sure to also get a new motor shaft seal to make sure you have a leak-free installation.
Reply
Is this the replacement motor for this pump?
Hello. The Century Motors 1.5 HP Up Rate Motor model B2854 is a compatible replacement motor for the TriStar SPX3200X Series Pump, motor SP3210Z1M. It is recommended that the motor shaft seal Pump Shaft Seal, 5/8", Viton - PS-3890, and Housing O-ring Housing O-ring - SPX3200T be replaced concurrent with the new motor.
Reply
I need this motor soon. What is normal delivery and expedited delivery?
Reply
Hello Harry. The Magnetek Century 1.5 HP Motor model B2854 is in stock and immediately available. The standard delivery time is 3-5 Business Days. Shipping options are available for review at checkout. Attached please find a copy of the INYO Pools Shipping Policy. Shipping Policy
Reply
does this model B2854 replace a STA RITE modelPHK2RA6f-1036
Reply
Hello Robert. The Magnetek Century 1.5 Hp Up Rate Motor model B2854 is the correct motor replacement for the Sta-Rite SuperMax Pump model PHK2RA6F-103L. It is recommended that the motor shaft seal, seal plate gasket, and diffuser o-ring be replaced concurrent with the new motor. The GOKIT78 contains the necessary parts to complete this project. Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78
Reply
I currently have this pump motor installed, and to be honest, it works great. But it is so incredibly loud, I was wondering whether it needs to be replaced (it's been on a while) or if that's just how this model sounds/
Hello Dave. Increasingly loud motor noise is the result of motor shaft bearing wear. Attached please find 2 brief tutorials describing the process. How To Replace the Bearings How To Replace the Bearings - Part II The front bearing is 5270-31 Bearing, 203 (Single) - 62032RS The rear bearing is 5270-31 Bearing, 203 (Single) - 62032RS Replacing the motor is the other option. Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854
Reply
Will this replace a whisperflo 2hp model no. 355014s
Reply
Hi Sean, you would need this Century 2.0 HP Motor - B2843 to replace your 355014S motor. Be sure to get a new motor shaft seal for a leak-free installation.
Reply
What do I need to replace this motor ? Replacement Pentair Square Flange Motor 1.5HP Energy Efficient 208V 230V Almond 071315S
Reply
Hello Thomas. The Century Motors 1.5 HP Full Rate Energy Efficient Motor 208-230 V model B2842 is a compatible replacement for the motor described in your communication. Century 1.5 HP Square Flange 56Y Full Rate EE Motor - B2842 This motor is manufactured by AO Smith/Century, the same manufacturer as your current motor with the exception this motor will be black in color instead of almond. It is recommended that the motor shaft seal, seal plate gasket, and diffuser o-ring be replaced concurrent with the new motor. These items are specific to the pump model and not the motor. Please provide pump model information and a recommendation can be made.
Reply
I have rebuilt this motor a couple times and believe i am ready for a new one. would this work as a direct replacement?
Hello Corey. The Magnetek Century Motor model B2854 (THP 1.65) is NOT a compatible replacement for the Century Motors model B2849 (THP 2.25). The Century Motors model B849 (THP 2.25) is the direct replacement. Century 1.5 HP Square Flange 56Y Full Rate Motor - B849 The Century Motors model B2842 (THP 2.21) would be a compatible replacement. Century 1.5 HP Square Flange 56Y Full Rate EE Motor - B2842
Reply
My pump was running and started making a very loud noise and then started leaking out the bottom. I replaced the seal but it kept making the loud noise. I can only assume the a bearing in the pump is bad. For about a week the pump ran without pumping water as the lid was leaking and not allowing it to prime. I assume the heat build up ruined the bearing. What are your thoughts? Century Centurion, part # 7-193993-05 5/8" shaft. Please tell me the proper motor for the replacement. Thank you.
Hello Phillip. The Century motors 1.0 HP Full Rate Energy Efficient (EE) Motor model B2841V1 is the direct replacement for the Century Centurion Motor model 7-193993-05. Century 1.0 HP Square Flange 56Y Full Rate EE Motor - B2841V1 From the information provided, the excessive noise coming from the motor is probably the result of bearing failure. Bearing damage can occur when the pump runs but fails to prime. Motor heat builds during operation and is not dissipated via the motor shaft to the circulating water. The result is bearing failure. The motor shaft seal, seal plate gasket, pump lid o-ring, and diffuser o-ring should be replaced concurrent with the new motor.
Reply
Thanks for your reply. In your response, you show the B2854 as being 1.5 HP, but in your reply, you told me about Century 1.0 HP Square Flange 56Y Full Rate EE Motor - B2841V1. So which one are we talking about? Will the 1 HP motor replace my 1.5 HP motor? My old motor is - part# 7-193993-05 Thanks
Reply
The Century 1.0 HP Square Flange 56Y Full Rate EE Motor - B2841V1 total HP is 1.65 (Voltage 115/208-230V) and the Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 total HP is 1.65 (Voltage 230/115). Please see How To Understand True Pump Horsepower - Up Rated vs Full Rated and How To Find The Correct Pool Pump Shaft Seal
Reply
I have a Pentair pump housing. It is making a loud squeal when running. What motor and pump housing would I need to replace/ rebuild? Is there a 2 hp option?
Thank you for contacting Inyo Pools, Most likely the noise your hearing is coming from the bearings going bad in the motor. It could be the impeller is rubbing against something in the pump housing, but you will not be able to tell that until you take the pump apart. If you went to 2Hp option you may need to replace the impeller and diffuser.
Reply
Have a Pentair pump known under part no. 168451. I need a replacement. Can you provide me with my options? Thanks!
Reply
Hello Charles. The Century Motors 1/2 HP Full Rate Motor SQ1052 (.95 THP - total horse power) is a compatible replacement for the motor part number 168451. Century 1/2 HP Square Flange 48Y Full Rate Motor - SQ1052 The Century Motors 1.0 HP Up Rate Motor USQ1102 (1.25THP) is also a compatible replacement. Century 1.0 HP Square Flange 48Y Up Rate Motor - USQ1102 it is recommended that the motor shaft seal, seal plate gasket and diffuser gasket be replaced concurrent with the new motor. These parts are specific to the pump and not the motor. Please provide the pump manufacturer & model and a recommendation can be made.
Reply
Wondering if you can help. I have a Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 working on my pool and yesterday pump stopped working and was making a large humming sound. Shut it off and tried to restart after a short time and same thing happened. Tried again about a half hour later and it starting working. Today, I tried to turn it on and same issue (humming sound) but a few minutes alter it starting working again. Any idea what the problem is?
Reply
Hi J, you can start your diagnosis by checking to be sure the impeller turns freely - a stuck impeller, frozen bearings or frozen shaft seal will make hand-turning the impeller difficult and may cause it to not start. If that is okay, then you might try testing the capacitor using the instructions in the How to Test a Pool Pump Capacitor guide to confirm if it's the culprit. If the capacitor is okay, you will have to replace the motor. The capacitor is a small part that looks similar to a battery. They are typically only good for around 5000 starts before they go bad. So, if you’ve had your motor for a long time and now it won’t reliably start or hums, the capacitor may be the issue.
Reply
Hi Rich...thanks for the feedback. Really don't know how to check impeller and problem seems to be hit and miss. Some times it starts and other times just makes a humming sound and I have to shut off pump. Have called a pool service company, hoping it's a simple fix. Thanks again for your help in explaining what might be causing the problem.
Reply
Here are some other HTG's you may find helpful. How To Clean Out a Pool Pump Impeller https://www.inyopools.com/HowToPage/how_to_clean_out_a_pool_pump_impeller.aspx How To Replace a Pool Motor Shaft Seal https://www.inyopools.com/HowToPage/how_to_replace_a_motor_shaft_seal.aspx and How To Find The Correct Pool Pump Shaft Seal https://www.inyopools.com/blog/how-to-find-the-correct-pool-pump-shaft-seal/
Reply
I need a replacement motor for a1.5 hp Pentair Whisperflow WF-26 (part number 011773). I currently have a 1.5 HP A.O. Smith motor number 177475. Is the Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 the appropriate replacement? Are there other options?
FYI, I have tried replacing the capacitor (which was successful in the past), the shaft turns freely by hand, and the timer is turning. I suspect something either something has failed in the motor or a connection has corroded.
Hi Jerad, the Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 will be a perfect replacement for your WhisperFlo WF-26 pump. We would recommend installing a Tune-Up Kit for Whisperflo - GOKIT32 which contains new o-rings and a new motor shaft seal to ensure a leak-free installation. The other option for that motor would be this V-Green 1.65 HP Square Flange 48Y Variable Speed Motor - ECM16SQU. When set up properly, variable-speed motors can save quite a bit of electricity.
Reply
Thank you. When I typed in my motor model number, the website recommended the Century 1.0 HP Square Flange 56Y Full Rate Motor - B2848. Since this has a 1.65 service factor, it appears to have the same braking horsepower as this B2854. Which is the correct replacement, B2848 or B2854? Thanks!
Reply
They both have the same total HP rating of 1.65THP and the same Amperage of 8.0/16.0. Please see How To Understand True Pump Horsepower - Up Rated vs Full Rated https://www.inyopools.com/HowToPage/how-to-understand-true-pump-horsepower-up-rated-vs-full-rated.aspx
Reply
I need to replace a Pentair 355023s. It actually has a receptacle for the electricity. Suggested replacements don't seem to. Any help would be greatly appreciated. Thanks!
Reply
Hello Susanne. The Century Motors 1.5 HP Up Rate Motor model B2854 is a compatible replacement for the Pentair 355023S. The preferred method for electrical connection is 'Hard Wired". However, a "Plug-In" electrical connection is acceptable if it complies with all state and local electrical requirements. The Century Motor model B2854 is rated for 230/115V. A "plug In" style electrical connection typifies a 115V connection. Please be certain to wire the new motor to the correct voltage. The electrical wires can be removed from the current motor and connected to the new motor's terminal block. Installation Guidelines
Reply
Can you verify this motor will replace part number 168453-24 Centurion motor for Challenger pump?
Reply
Hello Arthur. The Century Motors Magnetek 1.5 HP Up Rate Motor model B2854 is a compatible replacement for the Century Centurion Motor part number 168453-24. B2854 It is recommended that the motor shaft seal, seal plate gasket, and diffuser o-ring be replaced concurrent with the new motor. A GOKIT will contain these necessary parts. The correct GOKIT is dependent upon the Challenger Pump Series, CHII-N1, CFII-N1. Attached please find the Challenge exploded parts diagram. The GOKIT selections are the first items listed. Pentair Challenger Please match your pump model to the appropriate selection.
Reply
What is the wire size of the cord ?
Reply
Hello John. Selecting the correct electrical circuit wire gauge is important to the operation/efficiency of the motor. Attached please find a brief tutorial on this subject matter. What Is the Correct Pool Pump Motor Wire Gauge? Reference the Wire Gauge Charts, select the Power Supply Voltage, Motor Horsepower, & the Distance from the Fuse Box to the Motor and the proper Wire Gauge can be identified.
Reply
What 1-1/2 hp pump motor do you recommend to replace a Sta rite model P6RA6F-206L, and the seals?
Reply
Hello Steve. The Century Motors 1.5 HP Up Rate Motor model USQ1152 is a compatible motor replacement for the Sta-Rite Max-E-Pro Pump model P6RA6F-206L. Century 1.5 HP Square Flange 48Y Up Rate Motor - USQ1152 The Tune Up Kit (pre February 2015) GOKIT79 contains the motor shaft seal, seal plate gasket, and diffuser o-ring necessary to complete this project. GOKIT79 Attached please find the Max-E-Pro exploded parts diagram for reference. Sta-Rite Max-E-Pro Pump
Reply
Just want to confirm that a Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is compatable with a Jandy PlusHP PHPM 1.5 (it looks like it to me).
Also, what type shaft seal or GOkit do you recommend for the combination above?
Reply
Hello Derrick. The Century Magnetek 1.5 HP Up Rate Motor model B2854 is a compatible motor replacement for the Jandy Plus HP PHPM 1.5 HP Up Rate Pool Pump. Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 It is recommended that the motor shaft seal Jandy Pump Shaft Seal 5/8" - R0479400 and Back Plate o-ring Backplate O-Ring be replaced concurrent with the new motor.
Reply
Need to replace a bad motor. Hayward pump, Tristar Pump Series Motor Century SP3210Z1M, Y56Y, HP 1.5, SF 1.10. Can you help me confirm the parts list I will need. I think the motor is the B2854, and I will need the impeller screw SPX3200Z1, the pump shaft seal SPX3200SA, Tune up kit GOKIT81, Impeller Ring 0.75 - 3 HP - SPX3021R, Lubricant 1CC Pillow Pack.
Are there any other parts I might need?
Reply
Hello Kent. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is the correct motor replacement for the Hayward TriStar SP3210Z1M. The Tune Up Kit Hayward TriStar/EcoStar - GOKIT81 contains the seals and gaskets necessary to complete the project. The Impeller Screw - SPX3200Z1 should not need to be replaced if one is present. The Impeller Ring should be replaced if the current ring shows signs of wear. if the Impeller Ring shows signs of wear, also check the Diffuser w/ Impeller Ring
Reply
Do you have a Performance Curve for this motor? I'm trying to figure out how many gallons per minute this motor can pump based on 72 feet of water. The motor is 1.5HP with 3450 RPM and the wet end is WF-26 for 1.5HP pump. I've seen performance curves on other complete packages sell on your website. Thank you!
Reply
Hello Timothy. Performance Curves are specific to the manufacturer/model of the pump and not the motor. The WF-26 is a 1.5 HP Up Rate Model with a total horsepower (THP) of 1.65 manufactured with the Impeller, 1 Hp Full 1 1/2 Hp Up. (073128) It is the combination of the 1.65 THP motor and the Impeller that produces data that appears on the pump curve. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 with the same impeller reads as a 1.5HP pump on the Performance Curve. Whisperflo Pump 1 1/2 HP - WF-26 At 72 ft of Head, roughly 90 GPM.
Reply
Need a replacement motor for the pictured. Can you tell me which one to look for?
Hello Robert. The Motor, 1.5 HP Maxrate Dual Speed Tristar 208/230v (SPX3210Z2MER, SP3210Z2MER) is the direct motor replacement for the SP3210Z2ME shown in the attached photo.
Reply
I need a replacement pool pump motor for the Jandy 1.5 HP Plus motor pictured here. Can you tell me if you have one?
Hello Michael. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible replacement motor for the Jandy PlusHP model PHPM1.5. It is recommended that the Backplate O-Ring, Generic - R0446300 9-1/2" ID, 3/16" Cross Section O-521, and Jandy Pump Shaft Seal 5/8" - R0479400 be replaced concurrent with the new motor.
Reply
I am looking to replace my pool filter motor. I can't send a picture but it has part number 8-164383-24 and a CAT number of B128, 1 horsepower, type CX, on the spec document on the pump. Please advise where I can get a replacement. Thanks!
Reply
Hello Patrick. The Century 1.0 HP Round Flange 56J Full Rate EE Motor - B128 is the direct replacement for the motor CAT number B128.
Reply
can this motor be used on a 208V electric connection
Reply
Hello Youssef. Motors are rated for 10% over or under the nameplate voltage listed on the motor. This is a NEMA (National Electrical Manufacturers Association) requirement. A 230 volt motor can operate as low as 207 volts. A motor rated at 208/230 volts means the motor will operate at the 208 volt rating, not 10% under the 208 volt rating. Motors that are truly intended for 208 volts are nameplated for 200 volts. Such a motor rating would allow the minimum voltage to be 180 volts.
Reply
Looking for a replacement motor for this
Hello Melvin. The Century 1.0 HP Round Flange 56J Up Rate Motor - B228SE is a compatible replacement motor for the Century/Magnetek Motor model B228SE, 8-184981-21.
Reply
Can this pump motor replace a 56Y Waterway 1.5 hp single speed pump? Amps on current single speed pump are 7.7/15.4
Hello Scott. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible motor replacement for the Waterway Champion model CHAMPS - 115. The Pump Shaft Seal 5/8" - PS-1000 Face Plate Gasket - 711-1400 Diffuser O-ring - 805-0238 should be replaced concurrent with the new motor.
Reply
What is suitable replacement motor.
Hello Warren. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible motor replacement for the Century Motor model 0-193986-24 installed on the Jandy FloPro model FHPM. The Jandy Pump Shaft Seal 5/8" - R0479400 and Backplate O-ring - R0480300 should be replaced concurrent with the new motor. Attached please find the Jandy FloPro FHPM Series Pump exploded parts diagram for reference.
Reply
Will this replace this US Motor?
Hello. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible motor replacement for the U S Motors model EB854.
Reply
What is a suitable replacement for this pool pump motor. Thanks
Hello. The Century 1.5 HP Square Flange 48Y Up Rate Motor - USQ1152 is a compatible motor replacement for the Sta-Rite Max-E-Pro P6RA6F-206L. The Tune Up Kit Sta-Rite Max-E-Pro - GOKIT79 contains the necessary seals and gaskets to complete the new motor installation. Attached please find the Sta-Rite Max-E-Pro Pump exploded parts diagram for reference.
Reply
Went on vacation and the water got below the skimmer. Now pump is making a loud squealing humming noise. Will this replace the motor on my current pump? See pic
Hello Kristine. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible replacement motor for the Pentair SuperFlo model 340039, Pentair Motor model 177475. The Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78 contains the seals and gaskets necessary to complete the motor change. Attached please find the Pentair SuperFlo Pump exploded parts diagram for reference.
Reply
Hi,
I am attaching pictures of my current motor label. Will this one be a good replacement for it?
Thanks in advance
Hello Juan. The Century Motors model 7-193989-05 is a 1.65 THP Dual Speed Motor. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a 1.65 THP Single Speed Motor. If you wish to transition to a single-speed motor the B2854 is a compatible replacement motor. If you wish to maintain dual speed capability, the Century 1.0 HP Square Flange 56Y Dual Speed Full Rate Motor - B2982 is a compatible 1.65 THP Dual Speed replacement motor.
Reply
Will this motor replace the current motor I have? I have uploaded pictures of the label on my current motor to see if its compatible. Thank you.
Hello Angel. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible motor replacement for the Century motor model SP3210Z1M.
Reply
im'e looking to replace the motor on my whisperflo pump. your web site leads me to part B2854. under details it list's model WF-26, my model is WFE-26. My question is : is there a difference between the WF-26 and the WFE-26
Reply
Hello Fran. The Pentair WhisperFlo WFE-26 is a Single Speed Energy Efficient 1.65 total horsepower (THP) Up Rated Pump. The WhisperFlo WF-26 is a Single Speed Standard Efficiency 1.65 THP UP Rated Pump. The B2854 is a single speed standard efficiency 1.65 THP Up Rated motor compatible with the WFE-26 and WF-26. The Century 1.0 HP Full Rate Motor - B2841V1 is a single speed energy efficient 1.65 THP Full Rated motor compatible with the WFE-26 and WF-26. The GOKIT32 contains the necessary seals and gaskets to complete either motor replacement.
Reply
what's the difference between a B2854 and a B2854V1?
Reply
Hello Fran. The Century Motors B2841V1 is a single speed 1.0 HP, 1.65 total horsepower (THP) Full Rate Energy Efficient motor. Even though the motor is 1.0 HP, the Service Factor is 1.65. Horsepower X Service Factor = THP. 1.0 HP X 1.65 SF = 1.65 THP The Century Motors B2854 is a single speed 1.5HP, 1.65 THP Up Rate Standard Efficiency motor. 1.5 HP X 1.1SF= 1.65 THP. Energy Efficient versus Standard Efficiency references the rated amperage draw (electricity usage) of the individual motor. The B2841V1 is rated for 14.8 amps @ 115V, 7.4 amps @ 230V. The B2854 is rated at 16.0 amps @ 115V, 8.0 amps @ 230V. The B2841V1 uses less electricity, costing less to operate.
Reply
I need to replace motor on sand filter for my above ground swimming pool. It is a Century HT 1.5 HP Carvin Pool Equipment Model 177760PJ.
Reply
Hello Joann. Century Motors cross-references the Century model 177760PJ to the Century 1.0 HP Thru-Bolt 48Y Motor - BN25V1.
Reply
I have a Pentair Sta-Rite Max-E-Pro Pump #P6E6F-207L and want to see if you have a replacement pump. Or advise if you have a motor replacement for #354808S. It appears that your B854 might be the direct cross. Please advise. Thanks Brian
Reply
Hello Brian. The Sta-Rite Max-E-Pro P6E6F-207L is a 1.5 Horsepower (HP) Full Rate Pump, with a 1.47 Service Factor (SF). HP X SF = Total Horsepower (THP). The Century 1.5 HP Square Flange 48Y Full Rate Motor - SQ1152 would be the compatible replacement motor. The GOKIT79 contains the seals and gaskets necessary to complete the motor change. The Pentair SuperFlo® VS 1.5 HP Variable Speed Pool Pump - EC-342001 would be the recommended variable speed pump replacement. The Department of Energy Energy Conservation Standards for Dedicated Purpose Pool Pumps, enacted July 2021, mandates variable speed pool pumps for all new construction and replacements.
Reply
With this new pump, do we have to buy the seal and gasket?
Reply
Hello Nghia, yes it is recommended to replace the seals and gaskets when replacing a pool pump motor. Here is our Finding the Tune-Up Kit for Your Pool Pump guide that should assist you in locating the correct kit that you will need.
Reply
Hello, I have a US motors Cat No EUSQ1152 / Model C55CXKLT-5007 motor that appears to have died. No visible indication, just noticed my pool pump wasn't running today. Can you identify an appropriate replacement motor?
Hello Michael, the replacement motor for your motor model EUSQ1152 is the USQ1152. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide which should assist you with that.
Reply
The attached photo has the listed motor…what replaces this?
Hello Mark, the replacement motor for your Pentair WhisperFlo pump model WF-26 is the B854. We also recommend replacing the seals and gaskets when replacing a pump motor. The seal kit for your pump is the GOKIT32 for a standard chlorine swimming pool and the GOKIT32SALT for a saltwater swimming pool. Here is our "How To Replace A Pentair Whisperflo Pump Motor" guide that should assist with that process.
Reply
Is this a direct replacement for the century BPA450V1 motor?
Reply
Hello Lee. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a direct replacement motor for the Century Motors model BPA450V1.
Reply
Whats an UP RATE 1.5hp motor vs 1.5 B or 8-177896-22 56Y 3450rpm 230v B849 current motor?
Hello William, uprate essentially means "standard strength" while a full rate is like saying maxed which makes its total HP higher than what its labeled as. Your correct direct replacement motor will be the motor model B849. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that should assist in locating that kit.
Reply
Hello, I have a cetury centurion CAT B129 SN: 28317CHHP 1.5 Frame P56J, AMPs sf9.2/18.4.
What is the replacement motor for this product?
Reply
Hello, the replacement motor for your B129 pool pump motor is actually the B129 motor. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that should assist you with that.
Reply
I need to replace pump motor for Pentair WF-26/011773; would the B2854 work? or can you suggest another motor please
Reply
Hello Ralph, yes this will be a suitable replacement motor for your Pentair Whisperflo model 011773 pool pump. We also recommend replacing the seals and gaskets when replacing a pool pump motor. For you that will be the GOKIT32 for a chlorine pool and the GOKIT32SALT for a saltwater swimming pool.
Reply
I need to replace my Century HST110 pool pump. Which pump do you recommend to replace it ?
Reply
Hello Sharon. The Century 1.0 HP Round Flange 56J Up Rate Motor - UST1102 is a compatible replacement motor for the Century Motors model HST110.
Reply
Attached is motor i have and need replacement
Want to make sure i get correct one
Hi Michael, the direct replacement for your motor model 193986 is the B854. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that should assist you with that as well.
Reply
I replaced a bad capacitor on my pool motor and after placing power back to it - "POP", blue spark and smoke out of the motor. Not exactly sure what happened, but I'm betting I need a new motor. Can you advise?
If I do need a motor, can you suggest a replacement for a Century 7-193986-24 and replacement gaskets/seals? It appears the previous posts discuss the B2854, but that seems to be a 1.5 hp vs 1.0 hp.
Pump is Jandy ProSeries PlusHP, Model #: PHPF1.0
Thanks!
Reply
Hello Tyler. The capacitor may have originally failed as a result of a motor defect. The new capacitor provided current to the defective circuit and caused the electrical arc. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible replacement motor for the motor 7-193986-24. The Jandy PlusHP PHPF1.0 is a 1.0 HP Full Rate pump with a total horsepower (THP) of 1.5 HP. The B2854 is an UP Rate motor with a THP of 1.5 HP and is a compatible replacement. The Jandy Pump Shaft Seal & Backplate O-Ring should be replaced concurrently with the new motor.
Reply
does this work motor with Pentair SF-N1-1A/340038
Reply
Hello. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is compatible with the Pentair SuperFlo model SF-N1-1A, 340038. The SuperFlo 340038 is a 1.0 HP Up Rate Pool Pump. The Century B2854, while compatible with the incremental increase in horsepower, will not increase water flow despite the additional 0.5 HP. The Impeller would require upgrading to increase water flow. The Century 1.0 HP Square Flange 56Y Up Rate Motor - B2853 is also a compatible replacement motor - 1.0 HP Up Rate. The GOKIT78 contains the seals and gaskets required to complete the new motor installation.
Reply
Hello,
What would be a replacement for this century model in this picture
Hello, the correct direct replacement motor would be the SQS1152R. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide which should assist you with locating that as well.
Reply
Does the overall length measurement include the shaft ? I need a motor for my Pentair Superflo 1 1/2 hp pool pump, single speed Pentair part # 355022S
Hello Paul. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible replacement motor for the Pentair motor #196239 installed on the Pentair SuperFlo model SF-N1-1-1/2A/340039. The motor length, inclusive of the shaft, is 12.758 +/- 0.55 inches per the attached Century B2854 Motor Drawing. B2854 Motor Drawing The Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78 contains the seals and gaskets necessary to complete the new motor installation. Attached please find the Pentair SuperFlo Pump exploded parts diagram for reference.
Reply
LOOKING TO REPLACE A STA-RITE MAX-E-PRO POOL MOTOR #A100FLL ATTACHED TO MODEL # P6RA6F-206L I COULD USE THE MOTOR, SHAFT SEAL ,O-RINGS OR WHATEVER YOU RECOMMEND. LOOKS LIKE CENTURY B2854 1 1/2hp MIGHT WORK. THANKS!
Hello Richard. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible replacement motor for the Century/Magnetek motor model 196250 installed on the Pentair/Sta-Rite Max-E-Pro model P6RA6F-206L. The Tune Up Kit Sta-Rite Max-E-Pro (Pre February 2015) - GOKIT79 contains the seals and gaskets necessary for the new motor installation. Attached [please find the Sta-Rite Max-E-Pro Pump exploded parts diagram for reference.
Reply
Is this the correct replacement option for my motor (pic referenced)? What else do recommend to change when replacing the motor?
Hello Matt. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible replacement motor for the Century/Magnetek motor model 168453. The Tune Up Kit Pac Fab Challenger CFII/Pinnacle Series - GOKIT73 contains the seals and gasket necessary to complete the new motor installation on the Pentair Challenger model CFII-Na-1.5A/343234. Attached please find the Pentair Challenger Pump exploded parts diagram for reference.
Reply
My motor Part # is 8-168787-01 and matches the B849. I noticed this B2854 has the same specs and cheaper. I'm only using this pump for my koi pond (about 3000 gallon) for the filter and out flow on the valve that is only open 25% to filter the pond water. Can I use this B2854 instead of the B849?
Reply
Hello Tom, so your pool pump has a part called an impeller and possibly a diffuser specifically made for the correct replacement motor. With that said we would not suggest down sizing as that could cause more issues with your pool pump. The correct motor replacement for your motor part number 168787 is the B849.
Reply
What pump would work as a replacement?
Hello John, the correct replacement pool pump motor is the SQ1152. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that should assist you with that as well.
Reply
Looking for a pool pump replacement motor. The part number on my pump is O-193986-24. It’s on a Jandy Pro Series FloPro. It’s very noisy as of late. My guess is a bearing.
Hello Jim. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible replacement motor for the motor model 0-193986-24. The Jandy Pump Shaft Seal Backplate O-ring Diffuse O-Ring should be replaced concurrently with the new motor. Attached please find the Jandy FloPro FHPM Series Pump exploded parts diagram for reference. Attached please find a brief tutorial Why Is My Pool Pump So Loud? Motor noise is generally a result of motor bearing failure.
Reply
I have a 7-177475-20 motor and am going to replace it with a B2854. Which Gokit should I purchase?
Reply
Hi Troy, there are a number of different seal kits for these pumps. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that should assist you with that.
Reply
I’m looking for Sta-Rite motor # 196250. Pump model is PHK2RA6F-103L. It is 1.50HP and 3450 RPM. S.F.H.P(1.65). Do you have this motor or a replacement that would work properly. It a square flange.
Hello Tony. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible replacement motor for the Sta-Rite motor model 196250 installed on the Sta-Rite SuperMax Pump PHK2RA6F-103L. The Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78 contains the seals and gaskets necessary to complete the new motor installation. Attached please find the Sta-Rite SuperMax Pump exploded parts diagram for reference.
Reply
I have a century 1hp model number Hsq1102 that has lost suction can I replace it with a century 1.5 horsepower b254. If so what seal kit do I use. The reason for increasing hp I have added solar panels on the single story house roof and thought this would help with pump live. Serial number on existing pump is 17318j2
Reply
Hello Nick, if your pool pump/motor is actually turning on then you most likely do not need to replace the motor and there is another issue. If so, I suggest using this "How To Determine Why a Pool Pump Won't Prime" guide that may help pin point the issue. Also, if you do need to replace the motor then this is a suitable replacement. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that should assist with that.
Reply
I have a Pentair superfood high performance 1.5 hp 2 speed pump
P/N 071320S
motor # 177456
do you have a motor that would work for me?
the bar code number on the pump is 071320Z13316J2ML080000914
Reply
Hi Jaime, the direct replacement motor for your Pentair SuperFlo pump motor model 071320S/177456 is the B983. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Your seal kit is the GOKIT78. Here is our "How To Replace a Pool Motor Shaft Seal" guide that should assist with that process. I have also emailed you an estimate that you can convert to an order if you would like. Items are in stock and ready to ship.
Reply
I need a Century / Jandy 2 speed replacement pump motor. Current one is P/N O-193989-05, type CXPM, frame Y 56 Y, model 193989XCN. 230 volt, single phase, 3450/1725 rpm. Can you tell me which pump motor I need.
Hello Eddie, the correct motor replacement for your motor part number 193989 is the B2982. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that should assist you with that.
Reply
I need a replacement motor for my current Pentair. Could you steer me to the correct motor to purchase? Thanks
Hello Erik. The Century 1.0 HP Square Flange 56Y Up Rate Motor - B2853 is a compatible replacement motor for motor 196238 installed on the Pentair SuperFlo SF-N1-1A, 340038. The Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78 contains the seals and gaskets necessary to complete the new motor installation. Attached please find the Pentair SuperFlo Pump exploded parts diagram for reference.
Reply
I have a Super Flow SF - N1 - 1 - 1/2A/340039 1.5HP , 208-230/115V FR:Y56. Is this the correct replacement motor?
Hi Adam, the B2854 motor will be a perfect replacement for the motor on your Pentair SuperFlo Pump. Be sure to get a SuperFlo Tune-Up Kit so you can replace the gaskets and the motor shaft seal for a leak-free installation.
Reply
Which would be the correct replacement motor?
Hello William. The Century (A.O. Smith) 1.5 HP Up Rate Motor, Square Flange 56Y Frame, Single Speed - Model B2854 is a compatible replacement motor for the Century/Centurion 8-168453-23.
Reply
I have a Pentair Whisperflo high performance pump. Please let me know which pump will be a good replacement for it. Please see the attached picture. Thank you. Kindly, Pete
Hello Pete, yes this is the correct single speed replacement motor for your pool pump. We also recommend replacing the seals and gaskets when replacing a pool pump motor. For your Pentair Whisperflo you should also get the Tune Up Kit - GOKIT32 for a standard chlorine pool and the GOKIT32SALT for a saltwater pool.
Reply
Will this fit my old pump? I found it on another site and there was a slight variation in the model number. Mine ends in 6E and this one came up as 6F elsewhere. Also how long is shipping time to Florida
Hello Victoria, yes this is the correct motor replacement for your motor model 196250 from the picture. We also recommend replacing the seals and gaskets when replacing a pool pump motor. For the model pump assuming this was the original motor would be the GOKIT78. I have also emailed you an estimate that you can convert to an order if you would like. Items are currently in stock and ready to ship.
Reply
Will this motor work for my Waterway Champs 110? Any additional parts needed?
You will need this B853 replacement motor. When replacing your motor you will also need to replace your shaft seal with this Champs-110 Shaft Seal. We also have this great Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project. I have also emailed you an estimate that you can convert to an order if you would like. Items are currently in stock and ready to ship.
Reply
Is this a replacement for a sta-rite phk2ra6f-103L??
Hello Justin. The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is a compatible replacement single speed motor for the Sta-Rite SuperMax Pump model PHK2RA6F-103L. The Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78 contains the seals and gaskets necessary to complete the new motor installation.
Reply
I am looking for a replacement motor for my Hayward super pump
Reply
Hello Ivan, here is our "How To: Find a Replacement Pool Pump Motor" guide that we put together that should assist you with this process.
Reply
Is Your Pool Pump Mod. B2854V1/B2854 the same as a Model ST1152. Can this B2854 replace a St1152??? What are the differences???
Reply
Hello Jimmy, unfortunately no these two motors are different as your model is a full rated motor. Essentially that means that the total horsepower of the full rated models are actually higher than what they are labeled as. Here is a blog that we put together that explains these motor specifications called "How To Understand True Pump Horsepower - Up Rated vs Full Rated".
Reply
can this motor replace the JandyR StealthT (JHP Series) Motor, Full Rated, 1 HP, 1.40 SF, 115/230v (B128) motor?
Reply
Hello Julian, due to California Title 20 code you actually are required to replace this motor with an energy efficient model. In your case I would recommend the motor model ECM16CU. When replacing a pool pump motor we also recommend replacing the seals and gaskets. For your pump that would be the GOKIT77. I have also emailed you an estimate that you can convert to an order if you would like. Items are currently in stock and ready to ship.
Reply
I am looking for replacement motors for A. O. Smith Centry Centerian 7-177450-03 3450 RPM 1 HP and
7-177452-03 3450 RPM 1 HP. What do you have in the way of replacements, and is it acceptable to replace the motor only on 20 year old units?
Hello Lloyd, the correct single speed motor for your motor part number 177450 is the B841. However due to California Title 20 code you require an energy efficient replacement motor. In your case we would recommend the ECM16SQU. When replacing a pool pump motor we also recommend replacing the seals and gaskets. For your pump the seal kit for a standard chlorine swimming pool is the GOKIT32 and for a saltwater swimming pool it is the GOKIT32SALT.
Reply
will this replace a sp3215zbe motor on a Tristar sp3215ee
Reply
Hello, I believe that your part number may be missing a number "1" before the letter "B". If so, then your replacement motor is the 5112-256. We also recommend replacing the seals and gaskets when replacing a pool pump motor. If you have the Hayward Tristar series pool pump then your seal kit will be the GOKIT81.
Reply
would this replace a "Centurion for Pac-Fab 168453-24 FR Y56Y 1.5 HP motor"
Thanks
Hello, the B2854 motor would correctly replace your 168453-24 motor. For the replacement of the motor, you will need a seal kit; if you are able to let me know what the model of your pump housing is, I would be happy to recommend a replacement seal kit for your pump as well.
Reply
I have a pump that is going bad, noisy. hard to read the name it's faded, looks like US LOYD but I have the model number - C53CXKLZ-5010. Can you tell me what pump will replace it? I have alot of other info from the sticker , some are hard to read but not sure what else to check. Can you help with this?
Hello, the correct replacement Century motor for your unit would be Century (A.O. Smith) 1.0 HP Full Rate Motor, Round Flange 56J Frame, Single Speed - Model ST1102.
Reply
Will this replace a Sta-Rite phk2ra6f-103L ?
Hello, yes, the Century (A.O. Smith) 1.5 HP Up Rate Motor, Square Flange 56Y Frame, Single Speed - Model B2854V1, B2854, will be the correct replacement motor for your unit. Additionally, you will need a seal kit for the motor replacement process, which would be the Pentair SuperFlo, Sta-Rite SuperMax Saltwater Seal Kit - Model GOKIT78SALT for your pump.
Reply
Will this would be the right motor to replace my old one. Please see picture below.
Thank you.
Hello Mike. The Century (A.O. Smith) 1.5 HP Up Rate Motor, Square Flange 56Y Frame, Single Speed - Model B2854V1, B2854 is the appropriate replacement motor for the motor 193986XCN. It is recommended that the Jandy Pool Pump Mechanical Shaft Seal - R0479400 Backplate O-ring for Jandy FloPro FHPM - R0480300 and Diffuser O-Ring, Jandy SHP, FHP - R0622000 be replaced concurrent with the new motor. Attached please find the Jandy FloPro FHPM Series Pump (2008-Present) exploded parts diagram for reference.
Reply
Would this be the correct motor to replace my pentair motor/ Please let me know what additional parts I may need to oder to replace the pump. Thank you
Hello Vance. The Century (A.O. Smith) 1.5 HP Up Rate Motor, Square Flange 56Y Frame, Single Speed - Model B2854V1 is the appropriate replacement motor for the 196239 as shown in the photo attachment. The Pump Model No. SF-N1-1-1/2A, 340039 identifies the pump as the Pentair SuperFlo. The Pentair SuperFlo Seal Kit - Model GOKIT78 contains the seals and gaskets necessary for the new motor installation. Attached please find the Pentair SuperFlo Pump Parts diagram for reference.
Reply
Will this motor work for and old Pentair Superflo replacement? The filter is Clean & Clear 520.
Yes, this is the correct motor for the Superflo model SF-N1-1-1/2A (340039). We'd also recommend replacing the seals when you replace the motor. The seal kit is part number GOKIT78.
Reply
