Part # SQS1152R
Warranty 1 Year
Dimensions 14.5" L x 9" W x 6.5" D
Century (A.O. Smith) 1.5 HP Full Rate Motor (Total HP 2.20), Square Flange 48Y Frame, Dual Speed - Model SQS1152R
**NOTE THIS MOTOR IS SHIPPED LESS HI-LO SWITCH. YOU MAY PURCHASE THE HI-LO SWITCH SEPARATELY BY ORDERING PART # 1011431-001.**
Voltage 230, High Speed HP = 1 1/2 Low Speed HP = 1/4, Max Amps @ High HP = 10.4 Max Amps @ Low HP = 3.7, Dual Speed, Square Flange, RPM @ High Speed = 3450 RPM @ Low Speed = 1625, Threaded Shaft, Frame = 48Y Used on the following models: Sta-Rite Max-E-Glas, Max-E-Glas II, Dura-Glas, Dura-Glas II, Dyna-Glas, Dyna-Max Pentair Whisperflow, Pinnacle and Anthony AR2 Series.
Note: NOT California or New York Title 20 Compliant.
California and New York Title 20 Compliant Options:
Variable Speed EVQ225
Can you replace single speed pump motor with dual speed pump motor?
Reply
Yes but you can't go with a higher HP than the single speed motor. For example if you have a 1 HP single speed you cannot go with a 1.5 HP dual speed motor; you would be able to use a 1 HP dual speed motor. Customer would need to purchase a toggle switch or timer to switch from high speed to low speed.
Reply
What is Service Factor?
Reply
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
Reply
Why do I need to purchase a new shaft seal?
Reply
We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
Reply
Why should I purchase a Tune Up Kit?
Reply
A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
Reply
Can you direct me to the proper hi low switch for this motor?
Reply
Unfortunately the manufacturer does not offer the switch for the 2 speed 220v motors any longer. If you already have a 220 volt timer (on/off) you would need an Intermatic T106R to switch from high to low speed. If you do not have a timer currently you would need the T10604R which is a 220v on/off timer and a high/low timer.
Reply
Less than 1 hr
Screwdriver, Pliers, Socket Set, Wrench Set
1 0
The Most Helpful Review
2 1
(4 out of 5 stars) Do-It-Yourself
Reviewed By: Do-It-Yourselfer from San Diego, CA ()
Pros: great replacement!
Cons: difficult to remove impeller
I very much like this product. Easy to install with exception of removing the impeller. Overall, great replacement motor!
Was this review helpful to you?
The Most Recent Reviews
1 0
(5 out of 5 stars)
Reviewed By: Lance from San Antonio, TX ()
I installed this new motor with no problems. It seems to run more quietly than the replaced one.
Was this review helpful to you?