Does this pump meet California code for pool pumps?
Reply
California law will vary but most codes require any pump over 1HP to be a dual speed or variable speed. For a 15,000 gallon above ground pool, I would recommend a 1.5 HP dual speed pump: http://www.inyopools.com/Products/02200001004959.htm
Reply
How many hours per day should I run my pump?
Reply
There are many factors to consider; bather load, gallons of water, pump horsepower, type and size of filter just to name a few. A good guideline is 8-10 hours a day. On the cooler days and early and late season, you can cut the run time down to 4-6 hours because there is usually less swimmers and cooler water requires less chemicals. In peak season, when it is the hottest, raising the run time to 10-12 hours per day will help to keep the pool clean and circulating during it’s time of heaviest use.
Reply
Is all I need to do is add hoses to each end and put them in the water to make it go?
Reply
You would also require a filter, the system would work as follows.... Pump with hose back to pool skimmer, hose between pump and sand filter and then a hose from sand filter back to the return wall jet on pool. If you already have this set up then you could just replace your pump whith this pump here. If you need the entire system which includes the pump, sand filter and hoses then you would require this complete pool pump & filter system
Reply
I currently have a side discharge pump. Can the pump be rotated 90 degrees, making it a side discharge?
Reply
Unfortunately, this pump does not have the ability to turn sideways to make the discharge a side discharge.
Reply
Does the side discharge rotate to match the filter cartridge?
Reply
Unfortunately the housing does not rotate on the NE6170B pump. If you need a pump with a housing that rotates, you would need the Hayward Matrix: http://www.inyopools.com/search_matrix.aspx?Keywords=matrix
Reply
what type of switch does it have or do you just plug it in and unplug to turn on and off?
Reply
This pump does not have a switch but you could use our Above Ground Pool Pump Timer to automate when the pump turns on and off. You can also use the timer as a manual on/off switch.
Reply
what is the GPM of this pump
Reply
The gpm rating is based of the feet of head your pump has. The NE6170B (BC2730) will do about 90 gpm at 20 feet of head.
Reply
I think isnt it better to buy the whole thing that piece it and it will be easier and already put together..and would this model fit the same fitting so I don't have to replace the fittings can you check DYNII-N-I DYNAMO listed 227T got it off the pump..Would it be better too just get all new and use old parts as back up parts odl parts work only broke off drain piece broke wont hold twist on clear lid
Reply
the port on this pool pump that sends the water to the filter looks to be straight up. my broken pump port sends the water to the left side. can you buy a pump like my broken one.
Reply
Yes we do carry a 1-1/2 HP Above Ground Pool Pump with Horizontal Discharge.
Reply
Hi, I was given a 20'x12'x4' above ground pool. The motor for the pump doesnt work and Im not sure if I have to get the exact same one, STA-RITE brand or if I could get a different one. Ive tried looking up the model and serial #s, but I cant find anything on those. What type of pump will I need to look for? I want to make sure it has enough power. We do have a filter.
Reply
Hi Ashley for your sized pool I would suggest the 1 HP Jacuzzi SLR Above Ground Pool Pump, this pump would do a great job on your pool.
Reply
Our Proline 1.5 hp above ground pool pump has died (Model PE71-II-H side discharge). Is this model a suitable replacement?
Reply
Sara, The 1.5 Hp Above Ground Pool Pump would not be a suitable replacement because the discharge can not be adjusted. You can replace it with the Speck E71 1 HP Single Speed Above Ground Pool Pump AG192-1100T-HST
Reply
I have a above ground pond approx. 4020gals. I am looking to replace my pump with a new one and noticed that the one I have is very similar to a regular pool pump any difference ?
Reply
Above ground pool pumps are designed to only work from gravity fed water versus the inground style which do not need that. In essence you can use an inground model pool pump for an above ground pool but not the other way around.
Reply
Can this pump 1.5hp be used on a Coleman 16 ft round pool. I have a new sand filter that holds 100 lbs of sand? Just purchased pool and don't like the little cartridge filter it came with.
Reply
The 1.5 Hp Above Ground Pool Pump (NE6170B) can work on your Coleman 16' Round pool.
Reply
I have a Hayward 1 1/2 HP Power-Flo Matrix Pool Pump that needs replacement for an 18' round above ground pool. Would this be a suitable replacement?
Reply
Shaun - Yes this would be a suitable replacement for 1 1/2 HP Power-Flo Matrix Pump. Be advised, however, it only is designed for top discharge. This pump cannot be adjusted for horizontal discharge.
Reply
we have an above ground pool since 2008 and the pump just died its a sta-rite 1.5 hp will this pump work
Reply
Yes this pump will work but if you have union connections from Sta Rite going from the pump to a Sta Rite filter then that will not work on that pump. You would need to use generic fittings and hoses.
Reply
I have an Omega Splash pool 16 ft. round with a 150 lb. sand filter will this pump work on it?
Reply
Hi Rodney, The 1.5 Hp Above Ground Pool Pump would be too large for that size filter, I would recommend the 1 hp Above Ground Pool Pump (NE6150B).
Reply
I have a Waterway 22" sand filter and hose assembly. The hose end to the pump does not fit this pump motor. I am having a time trying to find what I need. Please help.
Reply
Hi Pamela, You will a Union, Male End 1 1/2" Mpt (417-4060) that will attach to the pump , then the hose will attach to the adapter.
Reply
does this pump have some kind of reset, because i have no power and my circuits are not tripped?
Reply
Hi Paul, The motor on the 1.5 Hp Above Ground Pool Pump does not have a reset button. You would need to check the timer that the pump is connected to.
Reply
Is this pump self priming?
My 22x14x4 oval is sunken in the ground
& I was told I need a self priming pump
Help!
Reply
Tim- The NE6170B 1.5 Hp Above Ground Pool Pump is not a self priming pump. It is an above ground pool pump and will not work on in-ground pools.
Reply
strainer basket cover for pl1501 and hoses for pl1501
Reply
Doyle- The pump lid you will need for the PL1501 1.5 Hp Above Ground Pool Pump is the PO12728CR Pool Pump Cover. As for the hoses, no hoses come with this pump.
Reply
is this a self priming pump?? I'm a returning customer.
Reply
Chris- This is not a self-priming pump, the in-ground version of this pump is PL1600 1 H.P. In Ground Pool Pump.
Reply
I have a Hayward sp1580z2 will this work and what else will I need or recommended
? thanks Vince
Reply
Hello Vince, this pump, The PL1501, is a replacement pump for the Hayward SP1580. The port size is 1.5" and would not need anything additional. Please note that this pump does NOT come with union pipe fittings and those can be found here: PL1643.
Reply
I have a Hayward SP1510-Z-XBC 1 HP. Is this a good replacement....older pump....new 24'x52" round pool above ground?
Reply
Hi Helene, Yes this 1 HP PureLine Pure Pro XL would be an excellent replacement for your 1 HP Hayward SP1510-Z-XBC. This pump would be more than adequate for a 24' Round 52" Wall Pool.
Reply
will this replace a intex salt water pump 1/2 hp . the pool is 12x24 52inch deep
Reply
Hi Joseph, This filter could work with your Intex system with some slight re-plumbing. You would also want to make sure the flow rating listed on your filter which is normally stated as gallons per minute (GPM) is at least 60 GPM to be able to handle the output of the Pure Pro XL pump.
Reply
i have a intex SF80110 sand filter pump. is this pump a good replacement and is the port size the same?
Reply
Joseph, Unfortunately this pump will be too powerful your Intex Sand Filter. If you would wanted to replace your pump and your filter then this pump along with this 16" Sand Filter would be a good option
Reply
I currently have a Proline, 1.5HP, model PE71-II-V for my Above ground 18' pool. The hose that runs from my sand filter to the top of the pump has a nut that looks a bit like this: http://www.inyopools.com/Products/07501352022577.htm
If I buy this PureLine pump to replace the Proline (which is on it's way out), will I need to purchase one of these nuts to make sure the new PureLine pump fits the hose to my filter? If so, which one?
Thanks!
--Brian
Reply
Hi Brian, Most of the times that nut slides over the filter hose like this Filter Hose and Nut the female portion of the nut would thread right onto the the male thread of the PL1501 pump. You should not need to purchase a new nut as the ProLine uses a standard 1.5" female thread and the PureLine uses a standard 1.5" male thread.
Reply
Will this replace the cheap pump on an intex 12'x24'x53" pool
Reply
Hi Shayne, The main problem would be the filter on the Intex Pool would not be able to handle the output of the pump. For an Intex Pool we would Suggest pairing this pump with a 16" Sand Filter
Reply
I have a 24ft. above ground pool. I was running a 2hp Proline pump (came with the pool when we bought the house a few years back). Pump is toast. Will this pump work as a replacement?? I suspect the 2hp may heva been a bit too strong for the pool size (?). Would a 1.5 hp pump work??
Reply
In our experience we have found that 1 HP pump is more then enough power to properly circulate a 24' above ground pool. The good thing about going down from 2 HP to 1 HP is that the cost of operation is much less on the 1 HP.
Reply
I have a pro line pump 1.5hp model pe71-11-h. I have a metal ring at propeller that seems to binds propeller is it a bearing Ring that came apart
Reply
Hi Lucas, The only part that you could be referring to is the pump Shaft Seal.
Reply
I currently have the Sta-rite JWPA5EL-242, would this be a good replacement pump? Thanks
Reply
Can the discharge of the pump be rotated? My pump is a side discharge
Reply
Hi Michael, For this pump we do not recommend these be altered to side discharge. We took one and tried it leaves a large gap on the side of the pump. If you need side discharge then I would suggest the Jacuzzi SLR Side Discharge Pump.
Reply
I have a proline sd10-1n11xb. Would the pureline 1 hp ne6170b be a good replacement? If not what would be the cheapest way to go? The pump is good but the motor is seized Thanks!
Reply
Hi Brian, The PureLine would be a good replacement but you may have a little re-plumbing to connect the hose from the pump to the filter.
Reply
Hello. We have a 16 ft around and 4 ft deep Coleman pool. The pump is crapping out. It is a flowclear 90342. Would this pump be a good replacement? Is there anything else we would need to purchase to make it work?
Reply
Hi Dana, Yes this would be a good a replacement for your pump on your 16' round pool. It would be hard to say what fittings you may need to hook this up, could you send us a few photo's of your current pump and filter as this would help.
Reply
Need to replace a pro line PE 71 1.5 HP pump. Will this one be OK or do you have a similar 1.5 hp model?
Reply
Hi Tom, yes this should be fine as a replacement for a PE 71 1.5 HP pump. If you have flexible hose between the pump and filter then the plumbing should be straight forward. If you have rigid pvc between the pump and filter then you may have a bit of re-plumbing.
Reply
Can I replace a proline model # sd-10-1n11cb with a Pureline part # PL1501
Reply
Hi Juliet, This pump can replace the Proline SD-10-1N11CB, however, the connects may be different depending on if you're using a pump to filter hose. You may need this Adpater-417-4161.
Reply
I have a Summer Escapes pool and the pump just died on me. I need a "Summer Escapes F1000C 1000 GPH Filter Pump and Motor Assembly", but they run close to $200. Would this pump work? The only problem I see is that my current pump is designed to attach to the bottom of the skimmer and I don't know how I could do that with any other pump.
Reply
Hello, Unfortunately, this pump will not work with a Summer Escapes pool.
Reply
I would like to get a variable speed pump (not a two speed) for my 18 foot round above ground pool, but I am having difficulty finding one. Are variable speeds not intended for above ground pools?
Reply
Rick, Unfortunately, we do not have a variable speed pump for above ground pools.
Reply
Will this replace the dynamo 340197 pool pump?
Reply
Hi Tammie, This pump can replace the Dynamo Pump depending on the type of connecting from the pump to the filter. You may need the Buttress Adapter (417-4060).
Reply
Does this pump have an off and on switch?
Reply
Hi Lisa, No this does not include an on/off switch we would suggest using an Intermatic Above Ground Pool Timer which allows you to set the on and off times for the pump. The timer can also act as an on/off switch.
Reply
My brother and I bought a pump and filter system from you on 4/28/16 - order #647092 - when our electrician put a new plug on the pump to accomodate our timer box he had turned the system on and when the timer started the pump ran dry - the pump sounds like it's struggling and not as quiet as advertised but it works well and the psi is 15 which I think is high - if I order a new pump will this pump fit the existing filter?
Reply
Hi Susan, This pump might be too strong for a 14" sand filter, the PureLine 3/4 hp (NE6150B) will be adequate.
Reply
Hi,
I have a proseries 15x48 can I use this pump? If so, my current pump which came with the pool has to be on all the time. Does this one?
Thanks in advance
Reply
Tracy, Unfortunately, this will not work with a Pro-Series pool.
Reply
Can I use this to replace my Coleman pool pump
Reply
Although we have no specific information on what pump you currently have on your pool, yes, you can replace your existing pool pump with another. Just take into account that this pump has 1.5" connections/ports and is a 115v electrical connection.
Reply
I have a Coleman above ground pool 18X48. the pump that came with it is weak and I would like to replace it with this pump. Can I do that?
Reply
Although we have no specific information on what pump you currently have on your pool, yes, you can replace your existing pool pump with another. Just take into account that this pump has 1.5" connections/ports and is a 115v electrical connection.
Reply
The pump is turning off after a short time. Probably bad right. The pump is a flowclear 90342. Cannot find any info. What do I need to do?
Reply
Hi J.T, The pump is probably bad, you will need to contact the manufacturer or the place where the pump was purchased.
Reply
I was using the HAYWARD 1.5 HP RPM3450 (POWERFLO MATRIX) with the Pro series sand, but it stopped working and I need a new motor. Can I use this one ?
Reply
Hi George, This pump can be used as a replacement.
Reply
is this pump Square flange? how many days is delivery time once ordered?
Reply
The motor on this pump is a C-face round flange motor. Delivery time can vary between 5-7 business days for free ground shipping. This pump is available for Next Day Air, 2 Day Air and 3 Day Air shipments.
Reply
What filters work with this pump?
Reply
We have a number of different filters you can use with this pump. There are different options from Sand Filters, Cartridge Filters, and DE Filters from a number of different sizes and manufacturers. You can view the different filters at our Swimming Pool Filters page.
Reply
Will this pump replace the E71-1 Speck Pump
Thanks
Reply
You can replace with the PL1501, though it will not have the same flow rate as the E71-1. The E71-1 has a little higher flow rate compared to the PL1501. If that is alright for the system that you currently have than the PL1501 would be a good replacement.
Reply
I had to buy pool pump one week ago, he is don,t works please exchanged or return and to buy diffrent model Thanks Boris
Reply
Hello Boris, I do apologize that you are experiencing this issue. You will need to contact our customer service staff at 1-877-372-6038 to discuss the replacement of the faulty pump. When you call, please have ready your order number ready. You may be required to send us photos of your pump, but all of that will be discussed once we have spoken with you. Thank you.
Reply
I have a 1HP CYGNET WIT 2 INCH OUTLETS USED FOR A WATERFALL. CAN I USE THIS PUMP AS A REPLACEMENT?
Reply
That pump has 1.5" ports which would not be a problem, just have to use an adapter, but what is the distance in feet from the pump to the waterfall so I can tell you if this pump will be a suitable replacement for what you currently have.
Reply
I have a 18 by 52 above ground pool with a Hayward 1 & a half horsepower motor, will a 1 horsepower motor run it efficiently?
Reply
Yes a 1 horse power pump would be sufficient for a pool of that size.
Reply
would this pump work for an above ground intex pool? And what kind of filter system would I need with it?
Reply
Yes, the 1 HP Above Ground Pool Pump - NE6170B can be used with some Intex Pools in combination with a filter that has a design flow rate of 62 Gallons Per Minute (GPM). Depending on your pool type you may need the Hayward VL Series Sand Filter Systems - VL40T32
Reply
I would like to buy this pool pump for my 18 ft above ground round pool but my existing pump has a horizontal outlet to the the cartrige filter housing this looks like a vertical outlet on this one would this pump work,
Reply
Hello Sean, I would suggest SLR9 1 HP Pump Above Ground Horizontal Discharge - 94022430, but if you went with the PL1501 you would have to replumb to make work with your system.
Reply
Would I be able to rotate the discharge piece on the pump, due to my filter inlet is on the side?
Thanks and have a great day
Steve Tamalavic
Reply
Hi, the discharge port can be rotated so that you have a horizontal discharge. To do this you will need to permanently remove the Pool Pump Mounting Flange Key #15.
Reply
I have a 24ft. round 4ft. depth above ground pooI with a Waterway PH220-6, 2hp, 2 speed motor with a side discharge to my Waterway 808-0167.1008 filter.
The high speed on the motor went out but the low speed is OK. I changed both the start and run capacitors to no avail. I'm guessing I need a new pump.
Someone told me that I don't need such a large pump/motor. The pool should work fine with a single speed 1hp or at most a 1½hp pump/motor. What do you recommend for a new pump/motor.
Reply
I like the 1.5 HP PL1502 Pure Pro XL for a 24' round pool
Reply
Earlier I asked for a recommendation on a replacement for a dynamo pool pump motor part # 340197. I go an answer of 1 h. p. 115V thru bolt motor BN25 which is just the motor. I am wanting to replace the motor and the other section that connects to it with the strainer basket. Please recommend which one I need.
Reply
Hi Lisa, The PL1501 is a great pump and would be a suitable replacement for the 340197 Dynamo Pump, the only caveat is that the plumbing ports on the PL1501 are not in the exact same position as the Dynamo pump. This means that you may have some re-plumbing. If you are using flexible hoses between your pool and pump as well as your pump and filter then this may not be an issue. If the plumbing being in the exact location as your old pump is important then I would suggest this 340197 Dynamo Pump as it is still be produced and the plumbing ports are located in the same spots as your current pump.
Reply
What causes loss of primer and high pressure in the filter?
Reply
Hi, Vicki. A suction leak cause air to get into the lines can cause the issue that you're experiencing. You will need to check the pump o-rings and hose connections.
Reply
I have a 20'x48" above ground pool with a Summer Waves Sand filter pump. The pump is bad and I need to replace it. The pump did not give us adequate water flow. what pump would you recommend?
Reply
Hi Jack, I would suggest this PL1501 PureLine Pure Pro XL pump for your sized pool. Please note that the plumbing ports might not be in the exact same spot as your old pump so you may have some minor re-plumbing.
Reply
I am replacing a Pentair 1 horsepower pump. Would this one work for my pool.
Reply
Please call in with your pump model number or send us some images of the pump through our support request page so we can look into a compatible replacement.
Reply
Can i use this to replace.sta-rite jwpa5el-2a. ? I do not have the 2 on the end like some others
Reply
Hi Sarah yes you could use this pump to replace the Sta Rite jwpa5el-2a however the plumbing ports on the pump are not in the exact same location so you may have a bit of re-plumbing.
Reply
I have a hayward sp1580 that doesn't work....whats a comparable pump to this ...it's a 1 HP
Reply
You can go with this PureLine PL1501 or if you want the exact pump you have then the Hayward SP1580 Power Flo LX is still available.
Reply
I have a Pentair dynamo 1hp motor, would the pureline 1hp motor be able to be used in my application. I sure I would have to change hoses / fittings ?
Reply
For an above ground application, this would be a suitable replacement. You would need to use standard plumbing/hoses and fittings versus if you have a set up per Pentair only. I.E. unions at the pump. Also, you should be able to get those standard fittings, hoses and or plumbing at a local hardware store.
Reply
I have an Intex 8 ft., 6 sided pool that holds about 640 gals. The pump/filter that came with the pool is inefficient and want to replace it without costing an arm and leg so to speak. What would be a good pump/filter to replace this with?
Reply
Hi, Laura. You can use the Hayward VL Series Sand Filter Systems - VL40T32 for a pool that size.
Reply
My pool is 22' round by 48" the current pump is a little sluggish, I am looking for suggestions but my current lines are 2" diameter and everything I am finding is 1.5". Advise
Reply
Hi, Larry. Most above ground pool pumps have 1-1/2" ports which will have a 2" ID. If you have a larger enough filter you can go with a larger pump.
Reply
Can this pump be used in place of a Hayward power flo matrix sp5500z2?
Reply
Hi, The pump you have is a 1.5 hp but if you're looking to downsize the system then this pump can be used in place of the Matrix Pump that you have.
Reply
my current above ground pool pump is a Hayward 1 hp model sp15921cnp side discharge will your pump 1521 interchange ?
Reply
Hello, the PL1501 is not a side discharge unit, so this would not be interchangable.
Reply
Will this pump replace a Pentair dynamo pump
Reply
Nancy, It will replace it you are using a standard threaded hose adapter. if you are using a hose with a union fitting, the hose will not fit this pump.
Reply
I have a splash pool and bought Pl1501 but my hose doesn't tread on it looks to be just a bit to small. Any ideas? Thanks
Reply
Keith, If you are referring to the internal thread, any standard 1.5" hose adapter should fit. If you are referring to the outside threads, those are a specific thread pattern.
Reply
Can this pump be converted to side discharge by unbolting and rotating housing similar to the Hayward PowerFlo pumps
Reply
Hi, MJust. Yes, the discharge can be rotated. You will need to permanently remove the Pool Pump Mounting Flange.
Reply
Can I replace this pump with my existing sand filter?
Here is the exact model I have:
game-50D-Above-Ground-Pool-SandPro-Pump-and-Filter-Kit-sand-pro
Reply
Yes this PureLine Pure Pro XL Pump would be a great replacement for the pump on your current Game Sand Filter system.
Reply
I have a 18 * 48 round pool with a AquaPro 75 lb sand filter. Do I need a .75 or 1 hp pump to replace the old one?
Reply
Hi, Kenny. A 3/4 hp pump might even be too larger for a 75 lb sand filter. I would not recommend a pump over 3/4 HP.
Reply
Would this pump be the right hp for an 18’, 42” deep above ground pool? Our filter is 75-80lb sand filter.
Reply
Hi, Susan. This pump is too large for a 75-80 lb sand filter. A 1/2 HP pump will be sufficient.
Reply
do you have a 1.5 hp for above the ground pool? I have a Sand Dollar 40 filter and current pump is 1.5 hp
Reply
Yes we have the PL1502 1.5 HP Above Ground Pool Pump
Reply
Hi, I have a small above ground pool 16x8x3 what size pump do you recommend?
Reply
Hi, JR. A 1/2 hp to 3/4 hp pump will be sufficient for jus water circulation. If you're operating other equipment like a pool cleaner, heater etc, you will need a larger pump and a filter to match. If you can provide us with all of that info we can size you a pump and filter system.
Reply
Would this pump be a good replacement for a Century serial: 323073M
Part 7-186533-22?
Reply
Hi, Jessica. The Part # 7-186533-22 provided is for the motor, I will need the pump housing model in order to confirm if this pump is a suitable replacement.
Reply
I have an 18ft round above ground pool with a hayward Pro Grid DE 2420 filter. Wondering if this would work with my system.
Reply
Hi, Joe. This pump can work with your system as long as it does not exceed your filter's max flow rate of 48 GPM.
Reply
Currently have the Hayward Power Flow LX 3/4 hp pump that quit working. We have a 27' round above ground pool with 54' sides, but the center is dug out deeper (recently purchased a 72" expandable liner because the existing 60" kept slipping out). We have two bottom drains as well. Our current filters max GPM is 75. Would be ok to upgrade to a 1 hp pump?
Reply
Hi, Angie. Yes, you can upgrade to this 1 HP Pure Pro XL pump,
Reply
Hello , I have a proline 1.5 hp motor for a 18 ft round pool with a sand filter was wondering if the 1 hp motor would be ok?
Reply
Can the discharge be rotated to the 9 o'clock position?
Reply
Hello, yes this pump can have the discharge rotated to a horizontal positioning. To see how this is done, please click here.
Reply
Can this pump be used to vacuum debris from in ground pool? If so do you have adapters for it so standard vacuum hose will attach?
Reply
Being that this is an above ground pool pump no, it wouldn't work for that application. It wouldn't be able to get a prime going very well for it needs to be gravity fed water.
Reply
Can this pump be turned to a side discharge??
Reply
Hi, Jat. Yes, it can. Check out our How To Rotate the Discharge Port on a PureLine Pure Pro XL Pump guide.
Reply
Is this a suitable replacement for a Hayward SP1580 1 HP Power Flo Lx Pump?
Reply
Yes, this would be an excellent replacement pump for the Hayward SP1580 1 HP Power Flo Lx Pump. The gallon per minute rating should be equivalent.
Reply
I have a Hayward pro series sand filter. The GPM rate is 35 and holds 150lbs of sand. Is the PL1501 pump compatible with this filter?
Reply
Hi James, As long as this filter is being used on an Above Ground Pool then this filter would be a great match and would work fine for you.
Reply
Need to replace pump for my above ground pool pump. Pump is a waterco supermite model number 2401100U 1 hp please advise
Reply
Hi Roy, this would be a great replacement pump for your waterco supermite model number 2401100U, you may have a little re-plumbing but it should be minimal.
Reply
Would this be a good replacement for my Hayward Power-flo Matrix model #SP1592TLFP
Yes the PureLine PL1501 would be a great replacement for the Hayward Power-flo Matrix model #SP1592TLFP. However you would need to remove the twist lock cord on your old pump and install it on the new pump as the new pump uses a 3 prong plug, but this will be an easy swap out.
Reply
I plan on using this with a inground pond with two waterfalls I have a Jacuzzi laser 160 sand filter that sits in my shed about 5 feet from pond, would this pump work for that application?
Reply
Hi Wesley, Is this replacing and existing pump? If so could you give us the specs. on the current pump like the model name and HP. Will this pump be placed above or below the water level? Also, could you give the approximate dimensions of the pond like length, width, depth, and gallon size? Do you know if you are using 1.5" or 2" plumbing? Any of this information would help out to make sure we suggest the proper pump. You can click on the reply link below to supply us this information.
Reply
Pond is small 10-x10 about 3ft deep. Filter is above water level. 1 1\2 fittings. Pump that was on filter was original pump 1hp. Two water falls and a rock fountain supplied by 1in schedule 80 pipe each having its own shutoff valve.
Reply
Hi Wesley, Thank you for the information! Since your pump is above the water line you will need a self-priming pump which means the pump can pull the water up to it. The PL1501 is a gravity fed pump normally used on above ground pools where the pump is placed below the water level. I would suggest the PL1600 1 HP Pure Flow Self Priming Pump for your pond. The PL1600 does have 1.5" plumbing ports so you will need to get a reducer from 1.5" to 1" which you can obtain from your local hardware store.
Reply
Hello, I'm looking at this pump for an 18 ft intex pool the pump that came died after one season and was weak from new anyways. Would this make a better pump for us. We have the ports on the sidewall to hook the lines. I'd have to double check line size but I think 2 in. And 3 lines total.
Reply
Hi Andy, Yes this PureLine Pump would be a big upgrade from the Intex pump that came with your pool. You would need to get some Intex adapters to hook the hose up to the pump. And here you may view our purchase the Intex Adapters. The most common adapter would be this Intex Hose Adapter to 1.5" Pump Port
Reply
Hi, I need to replace my 1 hp Waterway Hi-Flo Center Discharge pump for a 15ft 52inch above ground pool. Will the above filter with side discharge work?
Thank you
Reply
Hello, Yes, this would be a good alternative replacement for you.
Reply
Will this work on a 24’ round above ground salt water pool.
Reply
Hello, This will be the model we would recommend. http://www.inyopools.com/Products/44400018086937.htm
Reply
My tidalwave 1hp pump needs replaced. I have a sandman 18in sand filter. Will this pump work. Pump is about 8ft from pool.
Reply
Hello, This will be a good alternative replacement for your pool and filer.
Reply
Would this pump replace a Pentair Model # DYNII-NI-1, part number 340197. 1 HP, 115 volt, 3450 rpm, max amps 12.0
Reply
My pump won't fill the filter basket area. Once I prime it it sucks all the water out and dosnt fill back in but water fills as it pumps. And since that happens i do not have much water pressure coming through the jet.
Reply
Hello Rob,Please review the How To Determine Why a Pool Pump Won't Prime http://www.inyopools.com/HowToPage/how_to_determine_why_a_pool_pump_won_t_prime.aspx
Reply
what filter system goes with the Hayward power flo LX 1 hp?
Reply
Hello, You can put a bunch of different filters on there. How many gallons do you have in your pool? Do you have an inground or above ground pool? H
Reply
We bought this pump last week and installed it yesterday. Is there an on/off switch? We couldn't find one. Thanks!
Reply
Need to replace H.E. Pump. Will this pump be a good replacement? What is your ship time to Iowa?
Yes this would be a good replacement for the pump in your photo. You may have a little re-plumbing but nothing major. Ship time to Iowa is 3-4 business days.
Reply
Will this pump be a proper replacement for this one?
Yes, this is a compatible pump replacement but you may need to use different standard plumbing connections if you have a package that came with a filter.
Reply
I have a intex 15'x 42" 5000 gal pool with intex sand filter pump 2100 gph. I loose section with a new vac. Will the pl1501 1 hp work
Reply
is this pump a good replacement for waterway HP1.0SPL
Reply
Hi Mike, In regards to power this would be a stronger pump then your Waterway pump. If your Waterway Pump is Side Discharge you can rotate the discharge on the PureLine PL1501 to be side discharge by following this Guide on Changing the PureLine Pure Pro XL to Side Discharge. You may also need to put some shims under the pump or filter so that the port on the PureLine Pump match up with the inlet port on your filter. Outside of these few modifications, everything would work just fine with this pump.
Reply
Is the 1501 a good replacement for a proline sd-10-1n11cb pump?
Reply
Hi Mike, This PureLine Pure Pro XL would be a great replacement for the SD-10-1N11CB, however, the connects may be different depending on if you're using a pump to filter hose. You may need this Adpater-417-4161.
Reply
I want to replace my DYNII-NI-1 with a PL1501 1-HP. What our the pros and cons if I upgrade to a 1.5 -HP to replace the old 1-HP unit?
Reply
Hi Ken, The PL15 series would not be the proper replacement for a DYNII-NI-1 since the DYNII-NI-1 is normally used for inground pools. Inground pools will require a self-priming pump since the equipment is normally above the pool water level. The PL1501 Pure Pro XL Pump is used on above ground pools and is classified as a gravity fed pump since the pump is below the water line and the water flows down to the pump. I would suggest our PL1601 Pure Flow 1.5 HP Self Priming Pump I think going up to the 1.5 HP would be a good choice as you will get a little more power out of your pump.
Reply
I’m thinking about downgrading my 1hp pump. It’s a small, above ground pool with about 5,600 gallons. Connections are great, but it doesn’t draw water in properly. For example, connecting a vacuum causes all pressure to disappear. Am I running TOO much hp?
Reply
Hi. A 1 HP pump is too large for a pool that size. You can replace it with a 1/2 HP or 40 GPM pump listed.
Reply
i have a Hayward 5180 T vari flowXLvalve. 1 hp 115 volt .
just went bad 2 days ago. I like this model, is this comparable to replace/
Reply
Hi Hamo, Yes the Pure Pro XL Pl1501 would be a suitable replacement for your 1 HP Hayward Pump.
Reply
I have an Intex ultra 18x52'' and the sand filter pump i have is 1/2 hp, it isn't putting out enough to run my pool cleaner. Does anyone have any suggestions on what 1 hp pump to use that works with Intex. I did check and according to the pool vac my pump should be enough to run it.
Reply
Hi Oz, this pump along should be good for your set up, you may also need to use a few of these Intex Adapters to pair the pump with your filter.
Reply
would this be a good replacement for Hayward Power Flo Matrix SP15921CNP
Reply
I have a above ground pool 15' x42" with a 2100 gph sand filter all are intex. What pump would I use that will work. Old pump is making a lot of noise and after a hr water won't flow.
Reply
We have the follow guide for picking out the right sized pool pump: How To Select Above Ground Pool Pumps
Reply
I see most of the pumps are using soft hoses from the pump discharge to the top of the sandfilter. Is there a reason for this? As an old pipefitter is there a reason I cannot use PVC with a couple of unions between the motor and the sand filter if I use long 90-degree fitting instead of the standard 90-degree. This would help with the turn and reduce water flow restrictions to the sandfilter. I would use unions so I can take it down if need be as well as for winter storage.
Reply
Hi, Ken. The reason is to reduce the restriction. You can use hard pvc and unions if you wish.
Reply
Is there an on-off switch on the pump?
Reply
I'm looking for a new.pump to match my Hayward s180t filter on a 16x30x4 oval aboveground
Hi Patrick, The PL1501 PureLine Pure Pro XL would be a great replacement pump to go with your Hayward S180T sand filter. The PL1501 would be the pump we recommend for your pool size.
Reply
I have a Hayward power flo matrix 1HP 115v 12.0 amps Will this pump work in it's place with the Hayward sand filter
Reply
Yes, this pump will be a good replacement for your current pump model.
Reply
I have a pentagram pump 115 volts. Not sure if it’s a 1 or 1.5 hp. Would this be compatible for my pool?
From other answers i have read this pump would be suitable for 24 ft above ground pool. My concern is that the electrical cord is different. My power source is not the standard three prong, I have the kind that has three weird shaped prongs and you twist after you plug it in. I am sure there is a name for it but this women does not know it. Do you have a pump with that type of plug.
Reply
Karen, we do not offer the 1 HP Above Ground Pool Pump - PL1501 with the twist lock cord. You would need to purchase the correct cord and then wire it to the new pump. The cord that would need would be the 3' Cord Assy. W/20a Twist-lock Plug - 31953-0101.
Reply
I have a Leslie's freestyle 15 foot above ground pool. I don't have any trees in my yard or near by. I have used a intex 2500 GPH pump/cartridge filter for the past 3 years and it has worked, but I have to change the filter every 2-3 days during season. I want to switch to a sand filter. Would this pump and Pureline 19" above ground sand filter/base work for my pool? Would it be better to go with the Intex Krystal clear 3000gph sand filter? Looking for longevity and minimum maintenance.
Reply
would this be the correct pump to match my filter? Hayward s=220T?
Hi Derek, with the Hayward S220T model sand filter any 1 hp above ground pool pump will be a good match. Here is the Waterway Hi Flo pool pump model NE6450 that will be an alternate option being that this pump is no longer available.
Reply
Can you ship this pump into California?
What size of sand filter would you pair with this pump?
Reply
Hello Nathan. The PureLine 1.0 HP model PL1501 is a single-speed above-ground pool pump and is not eligible for sale in California. It is not California Title 20 Compliant. The PureLine 1.5 HP Dual Speed model PL1507 is dual speed and California Title 20 Compliant. 1.5 H.P Above Ground Pool Pump Dual Speed - PL1507 The Hayward Sand Filter W3S244T Hayward Sand Filter with Top Mount Valve 24 Inch Tank - W3S244T or the Pentair Sand Filter EC-145322 Pentair Sand Dollar Top Mount Filters SD60 Almond - EC-145322 would be compatible with the PureLine Pump model PL1507.
Reply
Can you ship this pump to Yuma AZ?
Reply
Hello Andrea. The PureLine Above Ground Pool Pump PL1501 is available for shipping to the 85364 Zip Code, Yuma, AZ. Shipping option selections can be viewed at checkout.
Reply
Is there a warranty on this product? If there is how long is the warranty?
Reply
Hello Ariana, this pump carries a 1 year manufacturer warranty. I have also emailed you an estimate that you can convert to an order if you would like. Item is currently in stock and ready to ship.
Reply
