what is the warranty on the 1.5 hp reliant pool pump and the two speed pump. Also is the reliant motor the same as the Hayward super pump
Reply
The warranty on this pump is a 1 year warranty. The reliant motor is made by a different manufacture than the manufacture of the Hayward Super Pump.
Reply
We have a 16 x 34 pool. Currently have a 1 1/2 HP pump which is very old. It came with the house we bought. Would this pump be big enough for that size pool.
Reply
Hi Kathy, Yes this pump would be large enough for your 16 x 34 pool.
Reply
I have a Hayward Northstar Pump, Part No. 187629.02. Is this pump a suitable replacement?
Reply
Hi Noshir, This pump would be a little too small for replacing a Hayward Northstar Pump. A good replacement for your Northstar would be the 1-1/2 HP Jacuzzi Magnum Pump.
Reply
What is the nearest Hayward pump equivalent for a Hayward Northstar Pump, Part No. 187629.02, 1 HP 115/230V. I understand that Northstar pumps are no longer available.
Reply
Noshir, The closest would be the Hayward NorthStar SP3207X10.
Reply
led
I installed a new 1.5 hp reliant pool pump and it doesn't seem to have enough suction to run my navigator cleaner. The new pump doesn't seem to fill all the way to the top with water. Is that common with this pump?
I
Reply
Hi Louie - It sounds like you have a suction leak between the pool and the front end of your pump. Since you just replaced the pump, I would look at the connections you changed in replacing the pump. One way to isolate leaks is to temporarilly pack plumber's putty around the outside of each connection to seal off any air leak. Do this is sequence. When the pump basket fills completely, the last connection packed is your leak.
Reply
My pool pump has gone out it is leaking water every wear and the motor is old to. This may be a dumb question but this pump comes with everything I need to replace all the old stuff with? I'm pretty sure the pump I have now is a 1hp will the 1.5 HP be to much or just right?
Reply
Hi, This pump comes as pictured, you will need to get plumbing and or electrical supplies to completely install this pump. It would all depend on the type of pump you currently have. I would recommend that you review our How To: Size a Pool Pump guide for the info need to make sure this pump will work for you.
Reply
Is this pump a good replacement for the haywood 1.5hp super pump
Reply
The best way to describe this pump is that it is a generic version of a similar design of any large pool product manufacturer model.
Reply
I have a 1 11/2 pool pump that runs about 15 min then shuts down then after about 15 min starts again.does it have a thermal cut off?
Reply
Most pool pump motors do have a thermal cut-off. It sounds like your motor is running too hot and the thermal cut off is turning off the pump. Normally this is a sign that your motor needs to be replaced.
Reply
would this model replace my pentair SFN1-1-1/2A/340039? and what all would I need to make the change?
Reply
Hi Donnie, Yes the Pureline Pure Flow PL1601 would be a good replacement for your Pentair Super Flo SFN1-1-1/2A 340039. You may also need the PL1643 1.5" Pump Unions.
Reply
Can you tell me what size quick connect union would fit this pump? It arrived yesterday and the connection doesn't fit the ones for the old pump (Sta-rite 1.5 HP).thanks.
Reply
Hi Jamie, You would require this PL1643 1.5" Union
Reply
Could this pump replace a Jacuzzi Magnum Force?
Reply
Hi Lautie, This pump is not a suitable replace for a Jacuzzi Magnum Force pump. You do have the Jacuzzi Magnum Force Pump available.
Reply
I have a "Power Flo LX" presently. Does this pump have an on and off switch? If not, what pump does?
Reply
Hi Lisa, This pump does not have an on/off switch. The Power-Flo LX is still available and does have an on/off switch.
Reply
I have an old Pinnacle 1.5hp, The bearings are going and the housing is corroding. i was going to replace the motor. The replacement motor for it costs the same as this entire pump assembly. Whats the catch? Is it inferior to Pentair/Pinnacle in its lasting power? Are the parts hard to get? Are they expensive to work on? would this be a good replacement set up?
Reply
Hi Bobbye, The pump is not inferior to the Pentair pumps you're just not paying for the big brand name. This pump will not be a good replacement performance wise. The Speck Easy Fit PNT (IG281-1150M-0WF) or Pentair Whisperflo (WFE-24) are suitable replacement performance wise.
Reply
I currently have an Emerson 3/4 hp motor for a Hayward pump. Will this unit be to much power or flow as a replacement?
Reply
Hi Ed, To provide you with the answer to your question we will need to know the model of the Hayward pump you have and the feet of head of your pool.
Reply
I have the 72744 pool pump and the motor went out. I see the motor is no longer available. Do you have another motor that is plug and play with that pump or do I have to buy the complete set up for the motor?
Reply
Hi Jodie, You will have to replace the entire pump, the replacement motors are not currently available.
Reply
Would this be a direct replacement for a Reliant 72748 1.5HP or would plumbing be required?
Reply
The plumbing would be the same but the ports on the PL1601 are 1.5" where the Reliant is 2" so you would have to use an adapter which wouldn't be a problem since the PL1601 has both inside and outside threading on the ports.
Reply
Is the performance graph correct? Can the 1.5hp pump only push 35GPM at 40' head?
Reply
Hello- Yes the flow chart in the description is correct. The PL1601 1.5 H.P In Ground Pool Pump - 72744 has a flow rate of about 35 gpm at 40 feet of head.
Reply
is this pump suitable to replace an old aqua flo brass pump 1.5 hp 35,000 gallon pool with hayward suction sweep
Reply
Hi, For your set up I would suggest the PureLine Prime 1.5 HP Pump as it will give you the power you need for your pool.
Reply
I have a eco kleer PK1150 1.5 hp 1 speed Hi Flo pump and it went out. Will this be a match.
Reply
Hi Laura, It looks like the Eco Kleer is an above ground pool pump, so our PL1502 1.5 HP Pure Pro XL Above Ground Pool Pump would be a great replacement for your Eco Kleer.
Reply
I have a pentair 346203 with 2" fittings, would this be an appropriate replacement?
Reply
Hi, Peter. This pump would not be an appropriate replacement for the Pentair Challenger pump because this is not a high pressure pump.
Reply
10,000 gallon pool with pop up floor cleaners , spa and waterfall. Presently have 2" pipe. will the reduction to 1.5 inch fittings cause a problem?
Reply
Hi, Jim. This pump would not be able to operate a pool with all those features and I would also recommend a pump with 2" ports.
Reply
10,000 gallon pool with pop up floor cleaners , spa and waterfall. Presently have 2" pipe. will the reduction to 1.5 inch fittings cause a problem?
Reply
If you have 2" plumbing I recommend the PL2602 over the PL1601. It has 2" ports and is a more durable pump.
Reply
Will this pump replace my Sta rite model P2R450-1201? This pump is a 1HP and 3450 RPMs for my 25,000 gallon inground pool. I'm looking for a value hopefully as quite and somewhat more efficient.
Reply
Hi Joe, Yes this would be a good suitable replacement for your Sta rite model P2R450-1201.
Reply
IS THIS PUMP 110 OR 220
Reply
Hello- The 1.5 H.P In Ground Pool Pump - 72744 is a dual voltage pump and can be wired for both 115v and 230v.
Reply
I have the Hayward super pump 1.5hp (not the super pump II). Would this replace that pump and be easy to install?
Reply
The Pureline Prime, PL2602, would be the replacement pump for the Hayward Super Pump.
Reply
I have a Century model number C48K2N143C1C, 1HP WITH 115/230 VOLTS. Would this be a good replacement or what would you recommend?
Reply
What is the distance from your pump to your skimmers so I can calculate your flow rate to see if this will be a good replacement for you.
Reply
I have a sta-rite p2ra5e-124L pump running a 28000 gallon inground pool. Is this a good replacement?
Reply
Hi Frank, Yes this pump would be a suitable replacement for the Sta-Rite P2RA5E-124L. The plumbing ports are not in the exact location so you will have some minor re-plumbing.
Reply
Would this pump be a replacement for a Hayward 1 1/2 HP Max Flo pump SP1610-Z!-M?
Reply
Hi. Unfortunately, it may not depending on the feet of head of your pool. The Max-Flo pump has a higher performance rating than this pump.
Reply
I have an in ground pool. How do I determine what new pump I should buy.
Reply
It will depend on your feet of head and your current filter size. What is the distance from your pump to your skimmers and what is your filter model so I can calculate the flow rate needed and identify the correct size pump for your system?
Reply
I have a Jacuzzi 1UMF-S pool pump with a Pentair clean & clear 75 filter, will this pump be a suitable replacement?
Reply
Hi. The PureLine PL1601 pump is not a suitable replace for the Jacuzzi Magnum 1UMF-S pump. I would recommend using the same Magnum Force Pump 1 HP Pump - 94027110 as a replacement.
Reply
I have a 16 x 32 in ground. (about 22k gal) Only one skimmer approx 10 feet from pump. Have a Hayward Super pump 1hp now that needs replacing. Would this increased HP be a good idea and a suitable replacement?
Reply
Hi GJ, Yes for the pool you have described I would suggest the PL1601 1.5 HP Pump at your distance from the pool this 1.5 HP PureLine Pure Flow pump would be comparable to a 1 HP Hayward Super Pump.
Reply
I'm curious why it has threads on the outside. Is there unions I can buy for this to make it 2 inch?
Reply
The nut of the union is 2" but the slip fit where the plumbing will connect to is 1.5". The part number for that union connect is PL1643.
Reply
I currently have a Jacuzzi Magnum Force pump with an AO Smith Corp 1 hp motor (UST1102...model C48K2N143C1C) for my inground pool. There are multiple issues with the system (it is returning lots of air bubbles to the pool and the motor is ridiculously loud). The entire system is over 15 years old and I'm guessing it needs to be replaced. The diverter valve is also very old but I cannot tell if that is the source of the air leak. Any other suggestions besides new pump will be appreciated. thanks
Reply
Hi, Replacing the o-rings in the diverter valve and the pump can resolve the suction leak problem that you're having. Review the info in our How to Identify and Correct Air Leaks guide for more steps.
Reply
Would this pumpwork with the sand filter s220t my inground pool is 23,000 gallons and the return line is 30' away
Reply
For your set up I like the 1.5 HP PureLine Prime PL2602 a bit better.
Reply
I just bought a house with an inground pool. I had to replace the skimmer line because it was leaking. When replacing the line, we took the long way to avoid cutting concrete etc. The run from the skimmer is now 40 feet. My old DE filter is cracked, leaking etc. I bought a Hayward 24" sand filter. The pump is a 1Hp challenger pac fab centurion, which i would like to replace. Will this pump be suitable? Pool is 28k gallons. Thanks
Reply
Hello, Yes this would be a suitable replacement for the Challenger.
Reply
we need to replace our pump which is 20+ years old. its a Pinnacle, Pac fab 34-2319 model pump. the dimensions are 16'x32 3' to 8' deep. we also use a sand filter. the skimmer is roughly 25 feet away from the pump.
Reply
Hi Donald, this would be a good replacement pump for the Pac Fab Pinnacle 34-2319 pump.
Reply
I currently have a Hayward Super Pump 1HP in need of replacement, would like a higher HP as I believe the current isn't the proper size. I have a 16x32 rectangular pool with average depth of 7 or 8 feet. Would this pump be an ideal replacement/upgrade?
Reply
Hi Brittany, If you are looking for a larger HP version of the 1 HP Hayward Super Pump then I would suggest the PL2602 1.5 HP PureLine Prime as a suitable replacement.
Reply
I have a 16x32 pool with Purex NSP36 D.E filter. I believe the pump I have is an Hayward (leslie) 1hp super II 1 and 1/2 inch. Pump impeller and diffuser just went out. Will this pump work for my setting? Skimmer is 7ft away from pump/filter.
Reply
Hi, Miguel. This pump will not replace the Hayward Super II Pump. If you can accurately calculate the feet of head of your pool using the steps in our How To Size a Pool Pump guide, you can confirm if this pump will meet your pool needs.
Reply
Where can I purchase a replacement mechanical seal for this pump?
Reply
We do carry the mechanical seal for this pump and here is a link to purchase the Mechanical Seal
Reply
Will this pump be a good replacement for the Jandy HHPlus Series pumps? Models PHP & PHPU?
Reply
I would suggest the PureLine Prime Pumps are more suitable replacement.
Reply
Will this be replacement for ao smith century centurion b2854?
Reply
Hi, Johnny. The Century B854 is only a motor which is used to operate a pump. I will need to know the model number of the housing in order to know if this Pureline PL1601 can be used as a replacement.
Reply
How do I know if this run will fit our motor?
Reply
Hi, Sharon. This is a complete pump which includes the motor so this pump will not fit a motor. If you would like to replace your entire pump with this and would like to know if it can be used you can use the steps in our How To Size a Pool Pump guide along with the PL1601 Pump Curve.
Reply
this pump is good replacement for 4rj95 dayton is 2 hp
Reply
Hi, Jose. This pump is not s good replacement for the Dayton Pump - 4RJ95. The PureLine Prime Pool Pump 2 HP - PL2603 will be a good replacement.
Reply
I am converting a 50,000 gallon chlorine pool to salt water what kind of pump do I need?
Reply
Hi. I would recommend reviewing our How To Size a Pool Pump guide or you can use your existing pump if it's not an old style bronze pump.
Reply
I have a hayward super two 1.5 that is getting really loud and whines all the time. Would this pump be a good replacement or is the whine something that can be dealt with?
Reply
Yes, as long as the total horsepower matches or are very close between the two models.
Reply
Hi I have a 2.2 HP pump unit for my inground pool, manufactured by Century. Looks very much like yours. Do you have a 2.2 HP pump? Mine is broken. thank you!
Reply
Hi, Tom. We do not have a 2.2 THP version of this pump available. If you can provide the housing model and or pictures we can locate a suitable replacement.
Reply
Hello:
Is this a good replacement for the Sta-Rite P2RA5F-1821?
Thank you
Reply
Hi David, we would suggest the PureLine Prime PL2602 1.5 HP Pump as a good replacement for the P2RA5F pump. The plumbing ports are not in the exact location so you will have some slight re-plumbing.
Reply
what do I need to replace HSQ 165?, 1.65 HP
Reply
You may order the A.O. Smith 1 HP Square Flange Full Rate Motor - SQ1102 or the A.O. Smith 1 1/2 H.P Square Flange Up Rate Motor - USQ1152 essentially they are the same motor, they both offer dual voltage of 115/230V and will arrive factory set at 230V. If you are capable of wiring at 208-230 Volts you may order the 1.65 HP Variable Speed Pool Pump Motor Square Flange - ECM16SQU Please do not forget to order the Pool Pump Shaft Seal or Go-Kits. It is necessary to replace the pump shaft seal any time you replace the motor or decompress the impeller. How To Replace the Motor on Your Pool Pump
Reply
Will this pump replace a 1 hp hayward superpump motor?
Reply
Hi, Larry. This pump can be used to replace a 1HP Hayward Super Pump, however, the performance of the PureFlow pump is slightly lower.
Reply
What pump do you suggest when replacing a Hayward super pump 2 1 1/5 hp pump rs1500
Reply
Hi Gilbert, We would suggest the PL2602 PureLine Prime 1.5 HP Pump as the suitable replacement for the Hayward Super II RS1500
Reply
Is a 1.5hp pump sufficient to run a 16,500 cal. Pool?
Reply
Hi, Yes, it can. However, it will be based on the Feet of Head of the pool.
Reply
what are your suggestions for replacement of a Hayward sp4007x10ns 1 hp
Reply
Hi, Joe. Here are a few suggestions. Hayward TriStar 1 HP Max Rated Pump - SP3207X10, Hayward Super II Pump 1 HP - SP3007X10AZ, Pentair Whisperflo - WF-24. This Pure Flow - PL1601 will not be a recommended replacement.
Reply
How much HP do you recommend for 50,000 gal. pool
Reply
Hi, Rick. Pumps are sized based on the Total Dynamic Head or the Feet of Head of the pool and its features. If you can get us this info we can help you with sizing a pump for your pool.
Reply
Looking for availability of a "drop in" replacement for Hayward 2 speed SP2810X152 pump and motor. 1 1/2 - 3/4 HP 65 Frame 230 V. 3450/1725 RPM 8.5/2.5 Amp
Reply
Hi. The Hayward Super Pump - SP2610X152 is the closest pump available that can be used as a drop in replacement to the Hayward MaxFlo Pump - SP2810X152. The discharge side port is the only adjustment you'll need to make. The suction side port is the same.
Reply
THIS IS FOR A WATERFALL ONLY!!! What will work to replace a Jandy SHPF/SHPM model?
Reply
Hi Al, A comparable pump to your Jandy Stealth would be the PureLine Prime Pump and that would be the pump we would suggest for a waterfall. Here you may view the PureLine Prime Pumps.
Reply
Sp2610x15 is my pool pump. I would like to have a little more flow and for the pump to be quierqu. Can you make a recommendation?
Reply
Hi Melinda, The pump that would be the direct drop in replacement for your Hayward Super Pump would be the PureLine Prime and if you would like to a little bigger than your 1.5 HP pump then I would suggest the PL2603 2 HP PureLine Prime this pump would work out very well for you.
Reply
Is this a good replacement for Hayward SP2610x15 pool pump? what variable speed pump would be a good replacement for the Hayward mentioned.
Reply
Hi Jessica the best variable speed replacement pump for your Hayward Super Pump would be the 1.65 HP Variable Speed PureLine Prime Pump. This pump is great as it is a drop in replacement for the Hayward Super Pump. The PureLine Prime is also Energy Star Certified meaning it is eligible for any of the Power Company Rebates.
Reply
I have a very small salt water pool (approx 8000 gallons) It has a Pentair Challenger 2HP pump on it now but it seems to be getting noisier over the past couple of years. Which pump would you recommend to replace it?
Reply
The Challenger has two models, it will depend on what model you currently have before a recommendation is able to be provided for single speed pumps. If you would like to invest in a pump that has a return on the investment, it is best to review the IntelliFlo Variable Speed - 011018 It operates up to 3HP, it requires a 230-volt connection, and a minimum of 2" plumbing. Click here to view Pentair's Energy Calculator.
Reply
We have the Hayward SP2610x15 currently, I know this is a drop in model but one of the reviews said the flow connector sizes were not the same for Hayward and this brand. What else needs to be purchased to make pipes that is currently connected to our Hayward compatible for this brand? What plumping connectors would we need to get? Thanks!
Reply
Actually the PL1601 is not a drop in replacement for the SP2610x15. The PL2602 PureLine Prime would be the drop in replacement for your pump. If you currently have 1.5" Plumbing then you would require 2 of these 1.5" to 2" Plumbing Adapters
Reply
Looking to replace my Hayward power-flo matrix pool pump (single speed) for a above ground pool. Looking for quiet and energy efficiency. What do you offer.
thank you
Reply
Hi Gary. I would recommend the PureLine Pure Pro XL AG Pump.
Reply
We have a Hayward 1.5 HP pump for our 40,000 gallon in ground pool. Could you recommend a replacement?
Reply
Hi. We can recommend a replacement if you can provide us with your exist pump model or the TDH or Feet of Head of your pool.
Reply
Is it possible to remove the four thru bolts and rotate the impeller end of the motor so that the water outlet connecting to the filter comes off the side instead of the top and then replace the thru bolts?
Reply
Hi. Unfortunately, this pump does not have that capability.
Reply
I need the parts that joint the pipe to the pump for PL1601
Reply
Hello, here is the part that you are looking for: 1.5" Quick Disconnect Unions
Reply
Does this model have an on off switch?
Reply
Hi Molly, No the PL1601 does not have an on/off switch, you normally would tie this into a timer like the T101 or T104 Intermatic Pool Timers
Reply
I have a 1.5 hp pentair whisperflo pump can I replaced it with this pump pl1601 and use quick connect 1.5 to 2"
Reply
Hi Tony, We would suggest the PL2602 1.5 HP PureLine Prime as a more comparable pump to your Whisperflo pump. The pump curve on the prime is more similar to the Pentair Whisperflo
Reply
need to replace hayward 1.5 hp 220 1 1/2 inch
Reply
Hi Leon, For your pump we would suggest the 1.5 HP PureLine Prime as a comparable replacement.
Reply
Would this be a replacement for a hayward sp4015
Reply
Hi Adrian, No this pump would not be a suitable replacement for the Hayward SP4015 Northstar Pump. The pump we would suggest is the PureLine Prime PL2603 2 HP Pump. The PL2603 has the plumbing ports in a slightly different location then the SP4015 Norhtstar Pump so you will have some minor re-plumbing, but nothing major.
Reply
I am currently using a Hayward 1.5 hp super pump to push water 200' with a 8' rise to a pond. Which pump do you recommend as a replacement.? The current pump is failing after 4 years.
Thanks !
Reply
Hi Ted, For your application, we would suggest the PL2601 1 HP PureLine Prime Pump, the plumbing ports on the Prime are in the same location as your Hayward Super Pump so the installation should be pretty easy.
Reply
Will the model # 72744. Filter a pool of 30,000 gallons. Or will it be to small
Reply
Hi, Janet. It can, however, it will be based on the TDH of pool's circulation system and features. The Total Dynamic Head (TDH) is the is the measurement of resistance working against your pool pump as it pulls water from your basin and pushes it back to the pool. You can reference our How Do I Calculate Feet of Head for My Pool? Blog.
Reply
I currently have a Hayward sp1510z1xbc and when I check online that pump seems to be for above ground pools. Its very old so I was thinking of switching it to one of these pumps instead. I have an in ground pool approx. 11000 gallons. 3-7 feet in depth and approx. 12x26 feet. You think this will be ok or should I go for the 1HP version?
Reply
Hi, Martin. This pump might be able to be used. I will first recommend that you try to calculate the Total Dynamic Head of your system.
Reply
OK, so as far as I can tell, here are my specs... 3200 gal pool, total FOH = 42, GPM = 62.5, Hayward Perflex DE Filter EC65A (67GPM).
Would the PL1600 or the PL1601 be the proper replacement pump?
thanks
Reply
Hi Scott, From what you have described we would suggest the PL1601 as the correct replacement pump.
Reply
Would this work with a Whisperflo wfe-4 with a Century AO Smith B2841 ?
Reply
So the B841 is the replacement for the original WFE-4 pump but am not sure if you also meant to reference this Pureline complete pump. If so this Pureline is a similar total hp but technically is slightly less in total HP by about .15th of a horsepower.
Reply
I am looking for a replacement for a Sta-Rite SuperMax 1 HP Model PHK2RA6E102L, would this pump be a good idea?
Reply
Hi Jay, Yes the PL1601 PureLine Pure Flow would be a good replacement for a Sta-Rite Super Max 1 HP. The plumbing ports are not in the exact same location for both of these pumps so you will have a little re-plumbing but nothing too bad.
Reply
I have a hayward 3/4 hp sp4007ns would this pump work. I live in California.
Reply
Hi Terry, The PL2602 1.5 HP PureLine Prime Pump would be more of a comparable pump to your SP4007NS Hayward Pump and would be the pump we suggest.
Reply
I currently have a Pinnacle PFII-P1-1 1HP (1.25sf?) in ground pool pump. It has developed fractures in the pump casing and is beginning to leak. Would this be a suitable replacement?
Reply
Hi Mike, Yes this would be a great replacement pump for a Pinnacle PFII-P1-1 1HP pump.
Reply
Is this a acceptable replacement for a Jacuzzi Magnum Force 1.5HP? 12,000 gallon in ground pool.
Reply
We would suggest the PureLine Prime 1 HP Pump as a suitable replacement to your 1.5 HP Magnum as the GPM rating will be similar and the Prime has 2" ports like your Magnum pump
Reply
My Jacuzzi Magnum Force has threaded ports and this one does not.
Will I have to do PVC work as well?
Reply
In replacing an entire pump with another brand you will always need to replumb but these pumps do have internal threaded 1.5-inch ports.
Reply
I'm replacing a Jandy Plus HP 1.5. Will have to do re-plumbing?
Reply
I want to replace sta rite P2RA5F--182L. 1.5hp. Which one do you suggest?
Reply
Hi Ron, I would suggest the PureLine Prime 1.5 HP Pump as a comparable replacement pump to the Sta Rite P2RA5F--182L Dura Glas Pump. The flow rating on the PL2601 will be closer to that of the P2RA5F--182L
Reply
I'm looking to replace a Baker Hydro Aqueduct Series Pump Model #: 19B02502. It has a K53CXEPM-4759 Pool Motor (1081). Please let me know which replacement pump/motors I need to look at for purchase.
Reply
Hi Arnie, We would suggest the PureLine Prime 1.5 HP as a more comparable replacement to the Baker Hydro Aqueduct.
Reply
I have a Hayward SP26007x10 pump for a 30,000 gal unground pool. Would this be a good replacement?
Reply
I filled this question out under the wrong part piece. I want to purchase this pump but read the fittings do not fit my Hayward pump. I have 1 and 1/2 screw in fittings.
Reply
Tony, You can use 1.5" male threaded adapters to thread into the female threads on this pump.
Reply
Would this be a suitable replacement for my jacuzzi Magnum force model 1umf-s?
Reply
If you went with this pump then you would actually be going down approximately a quarter of a horsepower so would recommend not using this model as a replacement.
Reply
My pump just stopped I have a 35000 gallon in ground pool will this be powerful enough for it currently a hayward 1.5 hp. Also whats the decibel level looking for something a little quieter than my Hayward .
Reply
Hi, Bill. To determine if this pump will be a suitable replacement, we will need to know the Total Dynamic Head (TDH) of your pool. You can use the following Inyo guides to help you calculate this number, How To Measure Total Dynamic Head With Gauges, How To Measure Total Dynamic Head With Gauges and How to Size a Pool Pump for Your In-Ground Pool. The decibel rating of pump is not listed in the specifications so I'm unable to confim if it is quieter than your Hayward.
Reply
Hello,
Iam considering this pump as a replacement for my sta-rite 1hp mod.: MPRA6E-147L, please advise if this will work, I assume the difference in horse power will move more water and require the pump work less?
Regards
Reply
Hi, Steve. Comparing the performance curves of both pumps, your model pump MPRA6E-147L will move slightly more water than this Pure Flow 1.5 HP pump. That's because of the design of the pumps. However, this Pure Flow pump will still be able to provide sufficient water flow to meet your pool needs at a lower upfront cost. Use our How To Measure Total Dynamic Head With Gauges guide to calculate the TDH of your pool and the Pure Flow Performance Curve to confirm.
Reply
I have a hayward pump model sp2607x10 will this work to replace it?
Reply
how can i get munela for my pump for my reliant pump it is a 2" pool pump
Reply
Hi, Tom. You can download or view the Pool Pump Owner's Manual using this link.
Reply
I have an Advantage Manufacturing Inc HO 1.5 RPM 3450 Vols 115/230 Amps 18/9 Thermally Protected Pool pump duty mount CODE AE 1205.
Will this be an acceptable replacement?
Thank you
Reply
Hi, GWB. I'm unable to confirm using the limited info provided which is from the motor. To determine if this pump will meet your pool needs, check out our and How to Size an Inground Pool Pump, How To Measure Total Dynamic Head With Gauges, and How To Size a Pool Filter guides.
Reply
I need to replace a Jacuzzi 3/4 HP pump (model 7MF-S) for a water feature (water fall). What do you recommend?
Reply
Does this pump have enough suction to lift the water in the pool up an inline of about 4 feet, into the pump and filter, then return it to the pool ?
Reply
Hi, Tom. This pump has a suction lift up to 6’ above water level. You will need to calculate the Total Dynamic Head (TDH) to confirm with your 4 ft suction lift and current plumbing this pump will be sufficient.
Reply
I am replacing a FloTec AR25001-01. is the PL1601 comparable
?
Reply
Hi, Don. This pump might be able to be used to replace the AT25001-01 model pump depending on the Total Dynamic Head (TDH) of your pool.
Reply
Would this pump be a good replacement for my Jandy Variable Speed Pump see picture attached.
The PL1601 would not be the pump we suggest as a replacement for a Jandy Variable Speed Pump. We would suggest the PureLine Prime PL2606 as a suitable replacement. If you are tieing your Variable Speed Pump into a Jandy AquaLink Automation system then you may want to stay with the Jandy pump as you will get all of the read out of the Jandy pump on the AquaLink, however if you are not using a Jandy AquaLink automation system then the PL2606 would be fine.
Reply
I have a crack/leak in the pump housing and we are leaking water. It is a Hayward Self Priming pump but the model and serial are not visible. Motor is a 1081 Pool Motor EB796, similar to a few people below. I’d like to replace the entire assembly. Can you recommend based on the pictures? Thanks.
Hi Ben based on your photos we believe you have a version of the Leslies Hydormax II Pump and you will require this Leslies Hydromax II Pump Housing
Reply
Hi. I have a pure flow 1600 and it is not working and was wondering, since I need a new one if I can just switch it out for the 1601 model or stay with the 1600? Do they have the same size fittings and parts? Will that make a difference in anything pertaining to the pipes, connections, filter, etc in a negative or destructive way.
If I do purchase either one, does it come with everything I need, o-ring, etc. ready for me to just switch them out and go.
Reply
Hi, Angel. You can replace the PL1600 with the PL1601 if your filtration system is larger enough. It will be a drop-in replacement when it comes to the plumbing connections. The only thing that you might need is new unions depending on how it was plumbed.
Reply
What is the warranty for this pump? I purchased this pump in September of 2018 and it went out today, 2/17/19, it was working fine up until today.
Reply
Hi, Jim. This pump has a 1 year warranty. In order to proceed, we will need pictures of the motor and the nature of the failure.
Reply
Will this replace and work as well as a Pentair SuperFlo 340039 1.5 HP 115 230V Single Speed ?
Is this an energy saver product, and how?
Reply
Hi, CAB. This pump can be used to replace a Pentair SuperFlo Pump model # 340039. This is not an energy efficient model, this pump will use more energy than the SuperFlo pump.
Reply
I want to replace my Hayward 1hp pool pump for this 1.5 hp pump. My pool is 15000 gal. Will this pump be a good fit.
Reply
Hi Rafael, yes this would be a great replacement pump for your 1 HP Hayward Pump.
Reply
Is this pump compatible as a drop in replacement for a Hayward RS1500?
Reply
Hi. This PureFlow pump is not a compatible drop in replacement for the Hayward RS1500 pump, the Hayward Super II Pump - SP3015EEAZ will.
Reply
Do you ship everything with the 1.5 hp pump as shown in the picture? Also, vets get plus 10%? Thx
Reply
Yes, the pump comes as shown in the image on its page. We offer a 10 dollar off coupon for vets. Please call our office and one of us can assist you with that when you place that order.
Reply
I have a AO Smith 2 HP motor ( k48n2pa102a2) and not sure what type of pump it is that is about 15 years old. Motor has failed and for less money than just the motor I can replace the pump and motor with this one. The pump is for a large waterfall and wanted to know if 1/2 hp less would make that much of a difference. I figured might as well replace them both now and wanted to know if this was a good option or if you had other recommendations.
Hi, Bret. A 1/2 hp will make a difference. This PureFlow pump will not be a suitable replacement for the Dyna Glas Pump. I would recommend the Dyna-Pro Pump 2HP Energy Efficient 230v - MPRA6G-207L.
Reply
Hello, my hayward pump intertek 4001333 v/speed motor broke. To replace the motor is quite expensive. I was wondering if I am going to be ok if I install your pump. What would be cons and pros?
Thank you in advance!
Reply
Hi Anya, Could you take a photo of the pump model tag? This would allow us to determine if this pump would work as a suitable replacement for you. Simple click the reply button and then upload your photo.
Reply
I have a small semi inground pool 12 X 18 which had a one and a half horse power pump. It was a regular electrical 110 V plug. Would this be suitable as a replacement? It was not hardwired two electric just a regular plug.
Reply
Hi, AM. There is a good chance that this pump will be able to meet your pools needs. Since not all pumps are designed to perform the same way, we will need to know the Total Dynamic Head (TDH) of your pool or your current pool pump model.
Reply
I have a Hayward Model RS750CA would your MODEL # PL1601 BY PURELINE be a suitable replacement and what power does it use
Reply
Hi, Garry. Unfortunately, this Pure Flow Pump will not be a suitable replacement for an RS750CA model pump. You can use the Super II EE Pump 3/4 HP - SP3007EECA as a direct replacement or provide us with the required info outlined in our How to Size a Pool Pump guide.
Reply
I have a Hayward Model RS750CA would your MODEL # PL1601 BY PURELINE be a suitable replacement and what power does it use
Reply
Hi, Garry. Unfortunately, this Pure Flow Pump will not be a suitable replacement for an RS750CA model pump. You can use the Super II EE Pump 3/4 HP - SP3007EECA as a direct replacement or provide us with the required info outlined in our How to Size a Pool Pump guide.
Reply
I have a Hayward Model RS750CA would your MODEL # PL1601 BY PURELINE be a suitable replacement and what power does it use
Hi, Garry. Unfortunately, this Pure Flow Pump will not be a suitable replacement for an RS750CA model pump. You can use the Super II EE Pump 3/4 HP - SP3007EECA as a direct replacement or provide us with the required info outlined in our How to Size a Pool Pump guide.
Reply
hi i want to replace my Hayward max flo 1 hp with this pump
is this a good fit and will it change my electric bill
can hi put a timer to stop during the night
thanks louis
Reply
Hi Louis, Yes this would be a good replacement for your Hayward Max Flo II and yes you can use a timer like the Intermatic T104 or T101 Timer to help save on your electrical bill. The T104 is used on 230V and T101 timer is used on 115V
Reply
I have to replace my pool pump, it is a Dayton 4TY60 item# 1J08E , I'M looking at the 1.5 hp I think it's the 6001, would this be an upgrade.
Or at the least what would a good replacement be that would be under 200.00 ? Thank you LF
Reply
Hi, Lurriee. This pump will not be a good replacement comparing the two pumps performance curves. We also do not have a suitable replacement under $200.00.
Reply
Aloha currently have a Hayward Max Flo ll 1.5 hp pool pump.
I was told that the bearings are going out this causing it to squeel loudly when it’s on. I was looking to just replace just the motor to save cost being that I replaced the pump about 8 years ago. It’s getting expensive. I would like to maybe buy a new unit that will be cost affective and hopefully last longer and save me money in the long run. I’ve read pros and cons about variable speed pumps vs single speed, please advise, Mahalo
Hi, Vince, you will definitely save on your operational costs by using a variable speed pump and I think the PureLine PL1615 Variable Speed Pump would be a great replacement for your 1.5 HP Max Flo.
Reply
Will I have to change the existing plumbing?
Reply
Hi Vince the plumbing ports are not in the exact same location on these two pumps so you will have some minor re-plumbing but it should be nothing major.
Reply
I need to replace a 1hp motor/pump. Adding photos but I can’t make them out. Can you: 1. Decider what type motor I have? 2. Will this pump be a good replacement?
Thank you!!!!
Reply
Hi Tommy I'm sorry but we did not receive your photos, could you please click on the reply link below and submit your photos. This may take a minute or two depending on how large the file size. Once we get your photos we will be able to make the proper suggestion.
Reply
Tommy I found your photos and have uploaded them on your behalf.
Tommy if your current plumbing size is 1.5" then this pump will work well for you. If your pipe size is 2" then I would suggest the PureLine Prime PL2602 1.5 HP Pump as it the ports on that pump are 2" either way you will have a little bit of re-plumbing to do as the plumbing port locations are not in the exact same spot as your current pump.
Reply
Sounds good. I'll check the pipe size as soon as I get home and order. I see that the 2601 has 2" inlets and is a 1hp motor. Should I replace with a 1.5hp or will the 1hp be ok? Thanks
Reply
Thanks Tommy! If you go with the Pure Flow then I would suggest going up the 1.5 HP PL1601 and if you go with the PureLine Prime then the 1 HP PL2601 would be sufficient. The Pure Flow PL1601 1.5 HP would have a comparable output to your Sta-Rite pump where the PureLine PL2601 1 HP would also have a comparable output to your Sta-Rite.
Reply
I need a replacement motor for my inground pool pump that was here when we moved in 20 yrs ago. I believe it says Sta Rite which I think is pentar. I am including photos. Could you please tell me what motor I need. Thank you.
Hi Margaret, If you are just needing to replace your motor then you will need the SQ1102 Replacement Motor and a tune-up kit. If your pump is before 1998 then you will need this Tune Up Kit for Sta-Rite Dura Glas Pumps Before 1998 and if your pump is after 1998 then you will need this Tune Up Kit for Sta-Rite Dura Glas Pumps After 1998. If you are not sure if your pump is from before or after 1998 then we put together this Video on How to Determine if your Sta-Rite Dura Glas Pump is from Before or After 1998. Also when you tackle this project we put together a Video on How to Replace a Pool Pump Motor which you may find helpful.
Reply
What is the voltage on this pump motor?
Reply
Hi, Dennis. This pump can be wired for 115 or 230 volts. You can review our PL1600 & PL1601 Wiring Instructions 115V & 230V guide for more info.
Reply
My pool is 18x36 20,000 to 30,000 gal. will this pool work on it
Reply
Hi Hays, Do you know the make, model and HP of your current pump? Or could you post a few photos by clicking on the reply link below? This will help us determine if this will work for your pool.
Reply
PL1601 says 1.5 inch port. I know inside threads are 1.5 inch, what are the outside threads.
Reply
Hi, Bill. The outside threads are not standard like the inside threads. We do not currently have unions that will work with the outside threads at this time.
Reply
Are you the only company that sells the pureline? How about giving me a contact with the manufacrurer.
Reply
Bill, Pureline can only be purchased at InyoPools.com.
Reply
I need to replace my pump. Would this work? Here’s my old one.
Hi, the motor on the PureLine Pure Flow will be as powerful as your USQ1102 motor. Most like you will have a little re-plumbing as the plumbing ports on this pump will be in a different location than your current pump.
Reply
How does this compare to a Pentair Super Flo 1.5 HP. and a Pentair Tristar 1HP.
Do you have performance curve charts?
Reply
Hi, Dave. The quality is comparable, however, the performance isn't depending on the total dynamic head of your pool. There is a pump curve is the product details.
Reply
Thanks for the reply. I am now planning on buying a new pump. I have been told that the 1 HP TriStar is bigger than I need. I have a 22,000 gal in ground pool, a 60 GPM sand filter, a heater, one skimmer, one drain, two returns, about eight 90s, and about 312 feet of 1 1/2" pipe. I come up with 78 for total head. Could you give me a list of pumps that would work for my pool? Thanks ?
Reply
Hi David, Thank you for that information it is quite helpful. Could you let us know the make, model and HP of your current pump? Did that pump seem to be pumping adequately when it was working properly? Once we hear back from you on this we will be able to make the proper suggestion.
Reply
i have an astralpool pump bx c1000 less than two years old, it is making a god awful noise. do you recommend replacing the whole system or just trouble shoot the issue?
Reply
Hugh, we do not have any information on the bxc1000 in order to get a relative cost on this for you. But, the noise is likely being caused by bad motor bearings. In this instance, we would usually suggest just replacing the motor, which in most cases range from about $130 - $200. But, at the price point that the PL1601 is at, it might be more cost effective to get the whole pump. We could better assist if we had more information on this pump. Please send a photo of your pump to upload@inyopools.com.
Reply
I buy a pool pump from you a week ago a 6201 in ground I'm have bubble trouble I 've try all your tips. I do not like the lid on this unit. If buy your unions will this fix the trouble
Reply
Hi, Hayes. It's hard to say if the unions will resolve the issue. Bubbles in the lid can also be caused by cavitation.
Reply
My pool has around 10,000 to 15,000 gallons, would this pump work?
Reply
Hello, We would need to know the model number of your filter and the total dynamic feet of head on your pool. Here are some great articles that explain on how to calculate the total feet of head on the pool. http://www.inyopools.com/Blog/how-do-i-calculate-feet-of-head-for-my-pool/
Reply
I am replacing a Hayward model sp2607x10. Would using your pump require replumbing the connections to the filter?
Thanks
Joe
Reply
This pump should match your current plumbing application or be very close.
Reply
Looking to replace a HEYWARD SUPER PUMP 1HP single speed SP2607x10. I had to get the info from the impeller which read spx2607C. Is this a good replacement or any other recommended replacement. Thanks
Reply
Would this replace my current motor/pump. Warn labels hard to tell.
Hi, Andrew. This Pure Flow Pump is not a suitable replacement. You will either need to provide us with the Total Dynamic Head (TDH) in order to determine if this pump will meet your pool needs.
Reply
replacing an AquaTool Model AT2515000, 1.5 hp 3450 rpm 220/110v pump. What would you reccomend?
Reply
Hi Ellsworth, Yes this PL1601 would be a great replacement for the AquaTool Model AT2515000 pool pump.
Reply
Is this pump quite?
Reply
Will this replace Hayward 1.5 Hp super pump
Reply
This pump will not have as much power output as the Hayward Super Pump 1.5 HP. We would suggest the PL2602 PureLine Prime 1.5 HP Pump as a drop-in replacement for the Hayward Super Pump. The only difference on the PureLine Prime and the Super Pump is the PureLine Prime has 2" Ports where the Hayward Super Pump has 1.5" ports, however, a simple 1.5" x 2" plumbing adapter will allow for 1.5" pipe.
Reply
I would use this pump as a portable vacuum. I have an inground pool approx. 16000 gal 8 ft at deep end.
I recently purchased a hayward 1 hp above ground pump but can't get it to prime and pump water.
Can this pump be equipped with a plug in cord.
any suggestions would be appreciated.
Thanks
Reply
Hi, Don. This pump can be used with a filter as a portable vacuum system. Above ground pool pumps can't be used because they are gravity fed. This pump can be wired for 115 volts but not equipped with a power cord.
Reply
I am looking for the same type pump that I am taking out. it is AO Smith Serial no. 14512ch it says part no. O-193968-24. I cannot find it in your system can you help me?
Reply
Hi, Could you give us the information off of the motor for your current pump like HP, Amps, Volts, SF, Frame, Model #, etc.. Also could you give us the pump make and model information, common pump names would be Pentair Whisperflo, Pentair Challenger, Jandy Stealth, etc.. To supply this information click the reply link below, also if you could send a few photos those are always helpful as well. If you send photos then take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get any of this information we can make the proper recommendation.
Reply
I have a pump with the same part number from AO Smith. Its for a 15,000 gallon inground pool. Here's the image. Please consider the wiring diagram Will this work for me?
Hi Justin, Based on the specifications of your motor, the PureLine Prime 1.5 HP Pump would be more comparable to power output and gallons per minute output to your current motor. We would suggest the PureLine Prime 1.5 HP Pump The plumbing ports on these new pumps are not in the exact same spot as your current pump so you will have a little re-plumbing. One last thing could you send us a wide shot showing the complete pump to include where the pipes go in and out of the pump, as this could give us a little more info. to see if the PL1601 can work for you. Just click the reply link below to add additional photos
Reply
Hi,
I want to replace an AO . Smith set up. 1HP 3450 rpm Type B it's a USQ1102. Is this set up with the right voltage?
Thanks,
Jack
Reply
This pump has the same voltage as the USQ1102 and will have comparable output.
Reply
I have a 1.5 HP Sta Rite Max Pool pump currently. Would the Pureline 1.5 HP handle my 18x36 inground pool with about 25,000 gallons.
Reply
In order to confirm that the PureLine 1.5 H.P In Ground Pool Pump would replace your current pump, we will need to know the specific model number of the pump. Please send that information to upload@inyopools.com along with a photo of the pump.
Reply
Trying to understand GPM on the 1 1/2 hp pump. I’m putting in a electric heater they says it has a flow switch that goes from 20 to 80 GPM. Does the pump go higher than that? Would that stop the heater from working?
Reply
Kenneth, GPM is a factor of horsepower and the total dynamic feet of the head of your pool. In order to accurately measure the flow rate of this pump you first need to determine the total feet of head for your pool. You can learn how to calculate this value by reading our article "How Do I Calculate Feet of Head for My Pool?".
Reply
i have a hayward pool pump.1 1/5 hp 115 volts 15 amps. the one iam looking at has the same except yours has 18 amps. does that matter?
Reply
Hi Ann, No that will not matter and this would work as a fine replacement for your Hayward pump. Please note that the plumbing ports are not in the exact same location so you will have a little replumbing but nothing major.
Reply
I bought and installed a PL-1601 last june. I had it drained and dry all winter, this year it leaks where the pump meets the motor. I am guessing the pump shaft seal dried out and needs replacing. any other thoughts? What is the part # so I can get a new one?
Reply
Hi, John. The Pump Shaft Seal is what will need to be replaced if the pump body if free from any cracks. That part is listed on the Pureline PL16 Series Pump Parts Diagram page.
Reply
Is this compatible?
Hi Doug, Yes this pump uses a motor with a comparable power output as the motor in your photo. The plumbing ports on the PureLine are not in the exact same spot as your current pump so you will have a little re-plumbing.
Reply
Will this direct replace a Reliant Model 72748 Pool Pump?
Reply
Daniel, the PureLine 1.5 H.P In Ground Pool Pump will not be a direct replacement. The Reliant Model 72748 Pool Pump is a 2" ported pump, the PureLine 1.5 H.P In Ground Pool Pump is a 1.5" ported pump. They will move different amounts of water through your system every minute.
Reply
Will this be a direct replace for my current pump?
Hello - that motor label only identifies the motor and not the whole pump. To determine if this pump is a proper fit, we will need to identify your pump housing.
Reply
I have an above ground pool that is partially in the ground. My current pump doesn't stay completely filled with water. Will the pump resolve that problem.
Reply
Barry, there could be many reasons that your pump is failing to prime and they do not all have to do with the pump itself. Some issues may exist beyond the pump. We suggest reading our article "How To Determine Why a Pool Pump Won't Prime" to help isolate the issue. This guide discusses the common problems involved with a motor that won't prime. Most priming problems involve leaks in the suction side of the pump (between the pump and the pool) or clogged baskets.
Reply
Would this pump replace our existing pump?
Hi Ashley, Yes it will but most likely you will need to cut off your current unions and replace those with these PureLine Pump Unions
Reply
What pump with an Anthony vertical filter repack. The pump on it now is a AO Smith Corp. 1 hp Mod. C48L2n131 ser# 8B06 115/230 volts. 1081 design. Sk1102
Reply
Yes, this pump will have about the same total horsepower however, you may need to adjust the plumbing arrangements as they may differ from your older model pump port locations.
Reply
I want to replace a Hayward Self Priming Pump SP 1811 X 15 2. This pump is being used for a hot tub.
What Purline product should I get?
Good afternoon, based on you having a Hayward MaxFlo series pump and using it for a Hot Tub the PL1601 would be a good replacement.
Reply
Will the PL1601 match up with my older current system for replacement. Photos attached.
Thanks in advance!
This would be a great replacement pump for your current pump, the plumbing ports on this pump are not in the exact same spot as your current Sta-Rite pump so you will have some re-plumbing.
Reply
How and where do you cut current unions and replace with PureLine Pump Unions? What materials will we need to do it? Thanks
Reply
Hi. You will need to cut the pvc where you have at least 6" of straight pipe to reattach new pvc to the old. You will need Unions, PVC primer and glue, tape measure, hack saw etc.
Reply
Will the PL2601 pool pump be a good replacement for a Hayward SP3007x10AZ
Reply
When replacing a Hayward Super II with a Pureline Prime, it would be best to go up one notch in horsepower. The pump the Prime is modeled after, the Hayward Super Pump is like the little brother of the Super II so too accommodate for more flow the higher HP is necessary.
Reply
Would this pump be a replacement for the attached photo Jandy. If so how quiet is this pump
Hi, Rob. This Pure Flow 1.5 HP Pump - PL1601 is not a suitable replacement for your JHP1.5 Pump. Your current pump is designed to move three times the amount of water than this pump. This pump will operate quietly when installed using the manufacturer instructions.
Reply
Would this pump be a replacement for my current one? It's only a 3/4 hp. I have a 4,000 gallon fiberglass inground pool with solar panels
I have a 1.5 HP 1.33 SF 2.00 will this replace it?
Reply
Hello - in order to provide an accurate comparison of two pool pumps we would need to know the model number and/or the make and model of your current pump.
Reply
I have a Centurion pool pump and from what I can tell, the part number is 168451-24. It doesn't appear that there is a hp rating on the tag. Would this be a suitable replacement for my current unit?
Reply
This would be a great replacement pump for your current pump, the plumbing ports on this pump are not in the exact same spot as your current pump so you will have a little re-plumbing, but it should be nothing major.
Reply
Will this pump replace my Century SQ1152 pump? My pool is around 25K gallons. Both are 1.5HP but I am not finding the water volume on either.
Thanks to anyone who can help me.
This would NOT be the proper replacement pump for your pump. I would suggest the 2 HP PureLine Prime as great replacement pump, the plumbing ports on the PureLine Prime are not in the exact same spot as your current pump so you will have a little re-plumbing.
Reply
Thanks for the response. No trying to seem harsh, but why would you recommend the 2hp vs 1.5hp ( Other than the obvious additional 1/2 hp. Water volume variance? Just trying to understand. Thanks
Reply
Hi Dan, Thanks for the follow-up question and that is a great question. I was looking at matching you up with a pump which would have similar output to your current motor. Your current motor is a full rate motor which has a True HP (THP) similar to that of a 2 HP Up Rate Motor. Here some math which will explain this better. SQ1152 1.5 HP Full Rate - 1.5 HP x 1.47 Service Factor (SF) = 2.2 True HP. PL2603 2 HP Up Rate - 2 HP x 1.1 Service Factor (SF) = 2.2 True HP.
Reply
will this be OK to replace a 3/4 hp motor? I have a 4,000 gallon fiberglass pool with solar panels. Just wondering if 1.5 hp is too much
Hi Chris, looking at the pump flow curves this 1.5 HP pump would be comparable to your 3/4 HP Full Rate pump. This PL1601 would be a good replacement for you. The plumbing ports are not in the exact same spot with the new pump and old pump so you will have a little re-plumbing.
Reply
One more question, Are parts readily available if needed once warranty expires?
Reply
Yes Parts can be found through this link PureLine Pure Flow PL1601 Replacement Parts
Reply
Will this be ok to replace
SP2810X15 - Hayward MaxFlo Pool Pump
Or should I look at another pump?
Reply
This PureLine PL1601 Pure Flow would be a great replacement pump for your Hayward MaxFlo, the plumbing ports on this pump are not in the exact same spot as your current pump so you will have a little re-plumbing, but it should be nothing major.
Reply
My 1.5 hp model K48M2N110 impellor RS 1500 will this replace that
Reply
Hello - the PureFlow would not be a good replacement for your RS Series. The RS is a higher head pump than the PureFlow, meaning it flows more water if you match the horsepowers. For a closer flow output, you would need to go with the PureLine Prime Pool Pump 1.5 HP - PL2602 or the PureLine Prime Pool Pump 2 HP - PL2603.
Reply
Will this motor replace the one in the photo
This would be a great replacement pump for your current pump, the plumbing ports on this pump are not in the exact same spot as your current pump so you will have a little re-plumbing.
Reply
Would this be a good replacement?
So the PL1600 would be a better match but it is currently not in stock and may not be for another week or two. However, you can also use the model PL2601 as well.
Reply
So this model, pl1601, wouldn’t be a good fit?
Reply
So this model, pl1601, wouldn’t be a good fit?
Reply
Will this pump replace my UST1072 Hayward 3/4 HP for inground pool? Does it come with wiring or do I need to order a cord separately?
This would be a good replacement pump for your current pump, albeit a bit more powerful. The plumbing ports on this pump are not in the exact same spot as your current pump so you will have a little re-plumbing, but it should be nothing major. The pump does not come with a cord, if you would like a cord then you can use this 115V 6' Pool Pump Cord
Reply
Would this product be a good replacement for this equipment?
Sorry... I forgot to include one more picture... I really appreciate if you can help me confirm that this model can be used as replacement. This motor is for the water slide which has the water output ~8 ft above ground level
Curious if this pump combined with a Hayward 18 inch filter with Aqualoon would be an interesting option to simply do pool vacuuming (suction with 40 hose). We believe we might have a leak underground related to the skimmer/vac ports and trying to find a reasonable solution to still vacuum the pool without having to turn on the skimmer pump for long periods of time. We have a robot that moves a good amount of water for chemicals. More concerned about larger debris mitigation.
Reply
Yes, it is a great fit for the application if you hose sections up 40'.
Reply
Hi, I'm looking to replace the STA-RITE pump, model MPFA6F-147L, HP 1.5, SF 1.0, RPM 3450, VOLTS 115/230, AMPS 15.3/7.6. Please advise if this is a replacement model for my pump.
Reply
This pump would be a suitable replacement matching the motor specifications however you may need to adjust the plumbing for the port locations may differ.
Reply
I have a Magnum pump with a 1 HP motor. The filter is a Hayward 2420. Will this pump work as a replacement to what I have? Should I go with 1 1/2 HP or stick with 1 HP. I have a Baracuda X3 cleaner and looks like it needs more to move it properly.
Hello, We recommend staying with the 1hp for your unit. Your filter is very small and going up in size can damage your filter.
Reply
Hi,
Is this pump a goog replacement for my current pump?
Hi Guillaume, This would be a great replacement pump for your current pump, the plumbing ports on this pump are not in the exact same spot as your current pump so you will have a little re-plumbing.
Reply
Hi, I just received the pump ordered 3 days ago. Very fast shipping ! The connectors are exactly at the same place. I will have to do some plumbing as the in/out port connectors screw thread are different with my STA-RITE pump. The port size looks good (1 1/2 in) but do you have the specifications of the screw threads for the port connectors so I can replace the one I have ? Regards, Guillaume
Reply
Hi, You will need two of these PL1643 PureLine Unions for your pump.
Reply
Can you use this one to replace a Flotek 1hp pump. This pump is only for the waterfall feature, not the primary filter pump.
Reply
Hi Mark, This would be a good replacement pump for your current Flo-Tec pump, the plumbing ports on this pump are not in the exact same spot as your current pump so you will have a little re-plumbing.
Reply
My 1.5hp Hayward Power-Flo pump went out. I was going to buy the ProLine pump PL-1502, but now the website says that it’s no longer available. What pump would be a good choice? Another Hayward pump is roughly $250, while the PL-1502 would have saved me $100. Please advise....
Could you let us know the size of your above ground pool? Simply click the reply link below to provide that information and then we can make some suggestions.
Reply
My pool is approx 18x36 that’s goes from 4ft to 8 ft. I currently have the Hayward self priming super pump 1hp. Would this be a good replacement since mine is locked up
Reply
This would be a good replacement pump for your 1 HP Hayward Super pump, the plumbing ports on this pump are not in the exact same spot as your current pump so you will have a little re-plumbing. If you wanted a drop-in replacement for your Hayward Super Pump which means not re-plumbing then I would suggest the 1 HP PureLine Prime PL2601
Reply
I currently have the Purex triton- Whisper Flo WF-26C with 1.5hp Century 230/115v motor. Will the PL1601 be a suitable replacement for this? Thank you.
Reply
Hi, Kevin. This PL1601 pump is not a suitable replacement because the WF-26 is design to move more water.
Reply
Which motor do you recommend to replace the WF-26C I currently have? If I decide to just replace the motor, do you have a motor you would recommend for the WF-26c? Thanks
Reply
Hi Kevin, If you wanted to go with a complete pump then I would suggest the PureLine Prime PL2602 1.5 HP as a suitable replacement. the plumbing ports on the PureLine Prime are not in the exact same spot as your current pump so you will have a little re-plumbing if you go that route. If you just want to replace your motor than you will need this B2854 Replacement Motor and this Whisperflo Tune Up Kit
Reply
I have a Magnum pump and I am looking to replace with a new one. Will this pump work as a replacement to mine pictured below? Should I upgrade to a 1 1/2 hp, since my 1 hp barely moves the Baracuda G 3 I have.
Hi, Bob. This PL1601 pump is a medium head pump, yours is a high head pump so it's not a suitable replacement. In order to locate a suitable replacement, you will need to provide us with the Total Dynamic Head (TDH) of your pool.
Reply
My motor is overheating and shutting down. Think it's on its last leg. Which pump would you recommend to replace my A.O. Smith C48K2PA105? Thanks in advance!
Hi, Tim. In order to recommend a suitable replacement pump, you will need to provide the pump housing model. As for the picture provided, it's of the motor which the USQ1102 or PL2102.
Reply
It looks as though you sell the pump and motor assembly as one unit. I was just curious to know which assembly would be recommended to be comparable to the motor that is failing. I figured I would buy a new pump/motor assembly than just buy the motor and gasket kit. Thank you for your response to my initial question.
Reply
Hi Tim, if you are looking for the complete assembly then yes this PL1601 Pure Flow Pump would be a great option. The plumbing ports on the PureLine Pure Flow are not in the exact same spot as your current pump so you will have a little re-plumbing.
Reply
Hello...
I have Jacuzzi J-P150 Pool pump. The housing is broke. I would like replace pump and put something new. Is this pump works instead of my old one?
This pump would be a comparable replacement pump but you may need to adjust the plumbing as the port arrangements my differ.
Reply
I have an Emerson pool pump. HP1.5 230/115 V Cat#EB129 Mod:K63cxerk-4777
Amp 9.0 . What would be the best to replace it. It is humming. Tried the banging with the hammer, tried the reset the breaker box.
Reply
Is this pump big enough for a 30000 gallon inground pool? Also could a person put this on a timer so it isnt running nonstop maybe run for a half hour off for an hour type thing?
Reply
Hi, Kevin. This PL1601 pump can be used to on a 30,000 gallon pool, only if your Total Dynamic Head (TDH) is within its operational range. Check out our How Do I Calculate Feet of Head for My Pool? and or our How to Size a Pool Pump for Your In-Ground Pool guide for more info.
Reply
Is this a good replacement for my current setup?
This would be a great replacement pump for your current pump, the plumbing ports on this pump are not in the exact same spot as your current pump so you will have a little re-plumbing.
Reply
Will this pump be a good replacement for my Hayward 1600 1HP Series Super Pump? Our pool is a 16000 gallon inground. (Cant make out the pump s/n but the motor is an Emerson EB654.) The inlet and outlet pipe connections look to be roughly in the same spot as this pump.
Thanks!
Reply
I need to replace a jacuzzi j-p150 is this a good replacement?
Reply
Hi, Finley. This PL1601 pump is NOT a suitable replacement, you can use the Champion 1.5 HP Max Rate 1-SPD Pump - CHAMPS-115
Reply
is this pump a good replacement for flotec?
Hello, This would be a good replacement for your unit. http://www.inyopools.com/Products/00100018074613.htm
Reply
Hello,
Is this the exact pump you are selling here so I can use it as a replacement?
Can you tell what year my pump was? It is getting louder and I think the bearings are starting to wear out. Thank you for your help.
Hi, Steve. The pump you have has been discontinued. The motor was manufactured in 2017, however, I'm unable to tell you the age of the pump. The Sta-Rite Max-E-Pro 1 HP Up Rate Standard - P6RA6E-205L is the direct replacement to your existing pump. This PL1601 is not a suitable replacement.
Reply
I need an Inground pool pump that runs about 23 gpm I dont want overkill. Any suggestio? Thanks!
Reply
Hi. You will need to provide us with the Total Dynamic Head (TDH) of the pool in order for us to find a pump that will meet your needs.
Reply
Is this a suitable replacement for the aquatron ii
Hi, Larry. This Pure Flow pump is NOT a suitable replacement for the Aquatron II pump. I recommend the Pentair WhisperFlo Pump or Hayward Super II Pump.
Reply
Need to replace my pump, (see attached) would this be a good choice? Will plumbing be close?
Hi, Benjamin. This pump can be used as a replacement depending on the Total Dynamic Head (TDH) of your pool. This pump suction port is almost 3" lower than your existing pump.
Reply
Need to replace my pump, (see attached) would this be a good choice? Will plumbing be close?
Hi, Benjamin. This pump can be used as a replacement depending on the Total Dynamic Head (TDH) of your pool. This pump suction port is almost 3" lower than your existing pump.
Reply
I need a pump with more HP. My pool is about 30,000 gallons (salt water). Is this a suitable upgrade?
Hi there, I am looking to upgrade our current in ground pool pump to a 1.5 HP. I am including a picture of our current pump and would like to ask which pump you would recommend we purchase from you. Also, do you sell the hoses for hook up? Thank you for your help.
Hi, Cindy. Based on your current setup, increasing the pump size may not be a good thing. Your filter and plumbing must be adequate to handle the increased water flow. We will need to know the Total Dynamic Head (TDH) of the circulation system.
Reply
I need a new pump will this be suitable for my pool my old pump is in pic sending along with this question .
Thank you
Hi, Nancy. We will need additional info like the motor model and or the Total Dynamic Head (TDH) in order to locate a suitable replacement.
Reply
Hi can this pump be a replacement for a Max-E-Glas 2 pump?
Hi, Joel. Unfortunately, it will NOT. The performance scale of the Max-E-Glass II Pump is higher, I recommend the Max-E-Pro Pump.
Reply
I have an 1/2 hp 240 volt pool pump thats a old magnetek hayward pool product part #10 182261 04 volts 208-230/115 its continuous flow rpm 3450 amp 50'c time cont what can this be replaced with?
Reply
And what is (TDH)Total Dynamic Flow sorry for being so lame but the pool shop wants a lot of money to replace and aim 60 years old on a fixed income and confused on what to do, my hubby thinks any 1/2 hp pool pump will work but dam not sure can you help us please?
Reply
Hi, Isabelle. The TDH is the measurement of resistance working against your pool pump as it pulls water from your basin and pushes it back to the pool.
Reply
do you sell the pumps, without the motor? I have a 2 HP pumps, with a round flange?, not square... can I just by the pump and hookup my motor?
Reply
Hi, Rob. Unfortunately, we do not have complete pump without a motor available.
Reply
My pump has failed and need a replacement. From the photos what do you recommend. Also do I need additional parts to complete the installation
Hi Chris. yes the PL1601 1.5 H.P In-Ground Pool Pump would be a good fit for a switch out. For install you will also need to order 1.5" Male Threaded Union x 1.5" Slip Union - PL1643.
Reply
Want to change out my current pump, this is what it currently has. Will this be a direct replacement?
Hi, RMSI. In order to confirm if this pump can be used as a replacement, you will need to provide us with the pump housing model or the Total Dynamic Head (TDH) of your pool.
Reply
HI I was wonder if this model would be a great replacement for my Magnetek motor. Thank you.
I am replacing my pool pump. I can’t make out much on the nameplate besides 1.5 HP and 230v. Would you recommend the Pureline 1601 as a suitable replacement. It’s an inground pool and I also run the polaris from this same pump.
My pump is shot. Based on these pictures would this pump be a good replacement?
I was wondering if this pool pump would be a good replacement for my water feature pump. my current pump is 1 hp and use to work fine as far as water flow. would i need any additional parts? do you have in stock? Thanks
What info do you need to reccomend a great replacement. I took more photos to see if that helps. Thank you.
We would need the actual motor model, part or catalog number in order to confirm a good replacement motor for you. The image of the motor label was not quite close enough to read.
Reply
Hi I wanted to replace my pool motor and needed advice if this would be a great replacement. Everything matches except the amps. This pureline has a slightly higher amp count.
Hi. Comparing these pumps side by side, this PL1601 performs slightly lower than your existing pump at the same Total Dynamic Head (TDH). The Prime 1.5 HP Pump - PL2602 will be a more suitable replacement.
Reply
Looking to replace my pool pump would this work?
Hi, Debra. This PL1601 pump will NOT be a suitable replacement comparing the pump side-by-side. However, if the Total Dynamic Head (TDH) of your pool is within the range of this pump to provide the desired flow, you can use this pump.
Reply
Need to replace my pump(not working) and upgrade to 1.5hp from 1.hp. would the PL1601 be a good replacement?
I haven't got the Pump name but have attached the following photos.
Hi, Cliff. Unfortunately, we will need to know the pump housing model. We cannot make a pump recommendation using a just the motor.
Reply
I did the calculations on your u tube video for determining a pump for my in ground pool. the data is: 20,000 gallon pool. average feet of head is 32.5 (2 draw lines at 65 feet). salt filter is 50 gpm flow rate. the inlet pipe is 1.5 inches. will this pump work for me. I would like to run it 10-12 hours per day.
Reply
Paul, yes, based on the information you provided about your pool the PureLine 1.5 H.P In Ground Pool Pump would be a sufficient replacement.
Reply
My 1081 Pool Motor Cat. No. ESQ1152 bit the dust. Could this replace all of it?
Hi, Nick. Unfortunately, this PL1601 pump will NOT be a suitable replacement for your Pac-Fab Challenger Pump. The Pentair Challenger CF 1-1/2 HP 115/230V UR Pump - CFII-N1-1-1/2A will be the direct replacement.
Reply
Would this be a good replacement for my Hayward SP2610X15 Super Pump 1.5 HP Pool Pump? I have a 23,000 gallon in ground pool. My Hayward Pump was a little over a year old and the motor blew already so I want to stay away from that brand. Thank you!
Would this be a good rep,acement for my Jacuzzi J-P150 inground pool pump?
Reply
My pump on my 18000 gallon pool has give out on me and I need to get a new one. I cannot quite read the sticker on it but I have included some pictures of it. Will this pump work for my application and if not what would be recommended to replace it. They tell me that they think it is a 1 1/2 HP but I am not sure. Also would going up to a 2HP be recommended to up the pressure to help run my Zodiac MX-8 Elite cleaner better? Thank you for any help that you can give me at this time
Hi, Dewayne. We're unable to identify the pump you have so we're unable to confirm if this pump can be used as a suitable replacement. We will need to know the Total Dynamic Head (TDH) and the desired turn over rate in order to make a new pump recommendation.
Reply
This is the pump I currently have. I’d like to have another just like it. I can’t find anything online that matches it. Do yo have one? Is it affordable?
I replaced I believe a Hayward SP2810X15 just over a year ago with the PL1601. It is still pumping but is making a tremendous amount of noise.I was considering replacing it again, but see that the PL1601 is temporarily unavailable. Is there another suggested model?
Reply
Your PL1601 is out of stock for the season? The season is just starting! Any alternative models or another source/site I can obtain one from?
Reply
What pump/motor is this? I need to replace.
Due to the condition of this motor, you will also need to get the impeller part number and likely another image of the entire pump including the housing.
Reply
Follow up from earlier message.
Hi George, Can you remove the impeller from the pump and give us the part # off of the impeller. Here are instructions on How to Remove your Impeller
Reply
Impeller SP 3007-0
Reply
Thanks George that is the info. we needed. You will require the UST1102 Replacement Motor and this Hayward Super II Seal Kit
Reply
I've got a Pureline Model Pure Flow PL1611 pump can you tell me what shaft seal it would need ?
Reply
Wiring diagram for the PL1601?
Reply
Pete,Here is a link to the wiring diagram for the Pureline 1.5 HP In Ground Pool Pump
Reply
I need a direct replacement for this pump motor and replace the old pacfab 700. It’s 1 1/2 hp.
Hi, You will require this SK1152 Replacement Motor and this Pac Fab 700 Seal Kit
Reply
Hi, I would like to know if this pump would replace the one I have. I attached a picture of it. Thank you
We will need an image of the pump wet-end too. The image only confirms the Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 that interchanges into many different model pumps. How to Size a Pool Pump for Your In-Ground Pool https://www.inyopools.com/HowToPage/how_to_size_a_pool_pump_for_your_in_ground_pool_.aspx
Reply
is the PL1601 a replacement for the PL2602? and do you have one in stock
Reply
Hello Mark. The Pureline 1.5 HP Pool Pump model PL1601 is a replacement for the Pureline Pool Pump model PL2602. Currently, the Pureline PL1601 is in stock. The installation will require adjustments to the intake and discharge plumbing.
Reply
is that's fit to my existing pump model hayward C48L2N134B1 and is it come with the gasket and if not , please let me know the type to add it my order , thanks
Reply
Hello Edward, yes this would be a good pump replacement for the Hayward Super Pump 1.5 hp.
Reply
can this pump be shipped to California?
Reply
What is a good replacement for a Jandy Model No. FHPM2.0 pump?
Do you have 2hp pumps?
Reply
Hello Don. The Hayward TriStar 1.0 (1.85THP) HP Energy Efficient Full Rated Pump model W3SP3210EE is a compatible single speed replacement for the Jandy FloPro 2.0 HP (2.0THP) model FHPM 2.0 pool pump. The pump performance data is almost identical for both of these pumps making them interchangeable. Hayward TriStar 1 HP, Energy Efficient, Full Rated Pump - W3SP3210EE The Hayward TriStar 1.5 HP VS Pump model W3SP3202VSP is a compatible variable speed replacement to the Jandy FloPro 2.0 HP (2.0THP) model FHPM 2.0 pool pump. The pump performance data is almost identical for this pump as well. Hayward TriStar VS Pump - W3SP3202VSP
Reply
Do you have only the pump strainer gasket
Pureline PL1601
Hello Fabio. The PureLine Pool Pump Lid O-ring part number PL1586 is available as an individual item. Pool Pump Lid O-ring - PL1586 Attached please find an exploded parts diagram for the PureLine PL1601. This diagram will detail all available parts for the PL1601. PureLine PL1601
Reply
I have a pureline pump PL1601. the pump died and replacement motor is out of stock. What motor is compatible.
Reply
Hi Seth, a compatible replacement motor for this motor is the BN35V1. When replacing a motor we recommend also replacing the motor shaft seal. The PSR-200 Shaft Seal is recommended for freshwater pools and the Heavy Duty - PS-3867 shaft seal is recommended for saltwater pools.
Reply
I have a Waterway SVL56S-110 pool pump that needs replacement, will this pump be a good replacement?
Reply
Hi Alexander. We would recommend the Waterway Champion 1.0 HP Full Rate EE Pool Pump - CHAMPE-110 to replace your SVL56S-110. The PL1601 is a great pump but it does not have the same operating specifications as your old pump.
Reply
I am needing to replace this pump, will this work as a good replacement?
Thank you for contacting Inyo Pools, I would replace it with Hayward Super II Pump 1.5 HP Single Speed - SP3010X15AZ - W3SP3010X15AZ
Reply
Is there anything in a lower price range that we could replace with? Really not wanting to go above the $400.00 mark…
Reply
The Waterway Champion 1.0 HP Full Rate EE Pool Pump - CHAMPE-110 is not under $400.00 but is the only other pump we can recommend for replacing the current at a more economical price.
Reply
does it come with the connection fittings?
Reply
Thank you for contacting Inyo Pools, The PL1601 does not come with connection fittings. 1.5" Male Threaded Pool Pump Union x 1.5" Slip Union - PL1643 is sold separately.
Reply
