What is Service Factor?
Reply
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
Reply
Why do I need to purchase a new shaft seal?
Reply
We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
Reply
Why should I purchase a Tune Up Kit?
Reply
A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
Reply
Do you have a replacement form1.5 hp part 7 177476 20?
1081 pool pump duty mount horizontal. What
If so what else would I need and how $$?
JR Dobson
Reply
What is the sizing requirement for HP on a motor for a pool of 11-12K gallon size? I was told that they (a company that change owners in the middle of my pool construction) had installed a larger than needed HP motor.
Reply
Joe, Here's a step by step guide on How to Size a Pool Pump for Your In-Ground Pool. Once you have calculated what size pump you need then you can make the necessary changes to your current pump.
Reply
Is this the proper motor for a Pentair WF-28/011774? The motor # on the label is 177476.
Reply
Bob, The B2859 is the correct kit for the pentair WF-28 pump. I would also recommend the Whiperflo tune up kit.
Reply
Please confirm my order for a new motor with reference: A.O. Smith 2 HP, 56Y Frame, Up-Rate Motor 230/115 (B859, B2859), it WILL BE THE REPLACEMENT for my motor part # 7-193987-24 serial # 267073M Type CX FR Y56Y PH 1 Hz 60
Please email me to reconfirm or send me the exact replacement motor, asap
best regards
pedro
Reply
Hi Pedro, The B859 (B2859) would be the direct replacement motor for your 7-193987-24 motor.
Reply
Hello, I need to know the exact specifications for the motor needed for a Jandy PHPM2.0, Serial # R09FH0345. I think this is the correct one, but I need to be absolutely sure.
Thanks.
Reply
Hi, The A.O. Smith 2 HP, 56Y Frame, Up-Rate Motor 230/115 (B859, B2859) would be the correct replacement motor for your Jandy PHpm2.0 Pump. You would also need to replace the OEM Shaft Seal (R0445500).
Reply
I need to replace a motor a A.O. Smith Centurion with following specs:
part 7 -193987 -24 type CX FR Y56Y HZ60 RPM3450 Volts230/115 AMPS SF 11.2/22.4 TIME CONT ENCL DP FORM KJM CODE K Insul Class B AMB 50C
1081 Pool Pump duty mount Horizwith vent holes down
The serial number is 139093M. It is on a Jandy pump. The info on the Jandy label says Rated HP x S.F = Total Motor HP. 1.50 X 1.50 = 2.25
Reply
Hi Tony, The A.O. Smith 2 HP, 56Y Frame, Up-Rate Motor 230/115 (B859) or the A.O. Smith 1.5 HP Standard Motor - Full Rate (B858) would be suitable replacements for the motor you currently have.
Reply
I need the replacement bearings part number(s) for this motor. Can you help me on this?
Reply
Hi Matt, This motor uses (1) 304 Bearing (6304) on the shaft end and (1) 203 Bearing (62032RS) on the opposite shaft end.
Reply
I have a 13 year old century centurion 177476-20 on my spa.
Breaker trips after about 3 minutes of operation.
Would you suggest I rebuild or replace.
Reply
Hi John, With the motor being 13 years old I would recommend replacing it.
Reply
17+ yr old pump motor for waterfall stopped working. Can you pls help me with the exact replacement motor to buy? What other parts do I need? Only info I have: MagneTek Century Centurion Pool and Spa Duty. PART: 7-177476-20
AMPS: 11.2/22.4, FR: Y56Y, RPM: 3450, TYPE: CX, HZ: 60, TIME: CONT, CODE: G, ENCL: DP, PH: 1, SERIAL: BT9-30, INSUL CLASS: B, AMB: 40 C
FORM: KJM,
Reply
Hi Rick, The B859 motor is the correct replacement motor for P/N 7-177476-20.
Reply
I need to replace my A O Smith motor with part no: 7-177803-02. I will also need the pump and the strainer. This was a 105 hp motor. What motor replaces this and how much?
Reply
I have a 7-177476-20 2hp motor and need a capacitor for it. What would be the pn?
Reply
Hi Andrew, can you pull any part #'s or specs. off of your current capacitor? If so could you email those to us as that would help us determine the capacitor you need.
Reply
I have ordered a new a. o. Smith pump motor. Does new motor include a new gasket? Should I order a GOKIT or just order a new gasket. The pump will be attached to PENTAIR pump.
Reply
Hi, The replacement motors do not include any gaskets. We will need to know the model of the Pentair pump in order to get you the correct gokit or seals.
Reply
I have a Century Centurion A.O. Smith Part 7-193994-06 1081 Pool Pump Duty Mount Horiz with vent Holes Down Motor and need a replacement is there new part numbers to purchase by it is a 3450 RPM, 230 Volt, 8.8 amp motor
Reply
I have a AO Smith with Part# O-193987-24 Rated 2.00 X 1.13 = 2.26 HP. Will this fit as a replacement?
Reply
Good afternoon Mike, Yes this will be the correct replacement. If you can let me know what type of Pump this is going onto. Then I can let you know what seal kit you need.
Reply
Originally asked: "I have a AO Smith with Part# O-193987-24 Rated 2.00 X 1.13 = 2.26 HP. Will this fit as a replacement?". Thanks for the quick response, and sorry for the delayed reply. The filter I've got is a Flow Pro FHPM2.0 "Self Priming".
Reply
My motor part number is 0-193987-24, just double checking to make sure this is the correct replacement, it will be running A Jandy Pro Series pump model number PHPM2.0. Do i need any other parts to complete my rebuild?
Reply
That is the correct motor replacement and we advise to replace the shaft seal, back plate o-ring and the diffuser/impeller hardware. You may need the old or new style shaft seal. If the serial number on your front pump housing reads with a Pxxxxx or earlier then you would use the old style part number 5020-086. If not then use the new style part number 5020-087.
Reply
I have an old worn out Pool and Spa Duty motor with the following information:
Part: 7-196256-06
Serial: 011103M
Type: CX FR: Y56Y
HR: 1.5
What would be proper replacement motor and will I need to replace the shaft seals and/or other parts before I can move forward?
Reply
Do you have the model of your pump, not the motor? If not, if you could attach a picture of the complete pump so I can identify what you have to make things easier finding the motor and seals.
Reply
I have a Hayward SPX3215X20Z1PE with a century 7-F56AA13A04-25 2-HP MOTOR. Is this motor a direct replacement for this motor and pump.
Reply
Hi. The SPX3215Z1MR motor is the direct replacement for the SPX3215X20Z1PE.
Reply
Hello I have a Pentair Superflo SF- N1- 2A /340040 with 177476 what is the correct replacement pump and what other parts kit should I order. Thank you
Reply
Hi, Steve. This Century B859 Motor along with the Superflo Tune Up Kit - GOKIT78 are the parts you will need to get your pump running again.
Reply
I cant seem to find a replacement for Century Centurion Part 0-193987-24. Will your part B859 work. =the motor fits into a Jandy pump PHPM2.0 2.00X1.13=2.25
Reply
Ralph, There are several options for a replacement motor. If you are replacing a 56Y frame motor, this will be an exact replacement. If you are replacing a 48Y frame motor, you would need the USQ1202. Please be sure to replace the shaft seal when you replace the motor.
Reply
I need to replace the motor on my Pentair WF-28, 1.1 SF, 2 HP pump. The almond pump does not seem to have the original motor but a black A.O. Smith motor which might have been replaced by the previous owner. The label from the motor is not available. Which motor should I order? B859/B2859 OR B855/2855? What is the difference between the two. What additional seals/kits will I need? This is the first time I am doing it by myself.
Reply
Hi. I would recommend the B859/B2859 since it's a dual voltage motor if you're not sure of the operating voltage. The B855 motor is rated at 230 volts only and the B859 motor is rated at 115/230 volts. You will also need to get the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
I have a Pentair WhisperFLow pump and need a new 2 HP motor. What is the correct motoor for this pump. B855 or B859.
Reply
Hi, Robert. Between the B855 and B859 motor you can use either, the difference is that the B855 is rated for 230 volts only and the B859 is rated for 115/230 volts. Also, confirm the service factor (SF) of your existing motor, both of these motors have an SF of 1.10. I will also recommend that you get the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
Hi. I have a Century Centurion spa pump, that sounds like it's in the early stages of bearing wear. Looking to get a replacement motor to have on standby. What I have:
CAT B2842 Serial 133103M
Part 7-196256-06 Type CX FR Y56Y HP 1.5 SF 1.47 PH 1 HZ 60 RPM 3450 VOLTS 208-230
AMPS SF 9.6- 8.8 TIME CONT ENCL DP FORM KJM CODE H..... Do you have a recommendation? Thanks.
Reply
I have an AO smith pump SP3215Z2ME, part 7-K56AA24A04-05, y56Y, 2.5 HP, two speed pump i need to replace. Do you have a suitable replacement?
Reply
Hi David. This will be the most suitable replacement for your motor. Motor, 2hp Maxrate 2-speed Tristar 208/230v (, sp3215z2mer) - SPX3215Z2MER and please do not forget to replace the shaft seal. If you need assistance identifying your shaft seal you may contact our office with the full model number of the pump.
Reply
I purchased a replacement motor for my pool pump (P/N B859 replaced the original F56AA13A04). I'd like to rebuild the old one as a back up. Can you tell me what bearing part numbers go with this pump?
Thanks, Mike
Reply
Hi Mike, You would need two 203 Motor Bearings. We do have these two Bearing Videos which should help you out when you tackle this project. Video #1 How to Replace Pool Motor Bearings and Video #2 How to Replace Pool Motor Bearings.
Reply
which pump and capacitor would replace a Century O-193987-24? Thnx.
Reply
Hi, Doug. You can use this B859 motor as a replacement. The replacement Capacitor is p/n 628318-308.
Reply
I need to replace a Century Centurion motor part 7-193987-24, type CX, Frame Y56Y, PH-1, HZ 60, RPM 3450, Volts 230/115 , AMPS SF 11.2/22.4, Time -Cont, ENCL- DP, Form KJM, Code K, INSUL Class B, AMB 50. What is replacement motor info?
Reply
Is this the best replacement for a "Century, part :7-F56AA13A04-25, Serial : 31213J2, FR: Y56Y, Type: CX, HP: 2.00, SF: 1.1, CODE: G, RPM: 3450, VOLTS: 230/115, HZ: 60, INSU CLASS: F, PH: 1, ENCL: ODP, AMPS: 10.5/21.0, AMB: 50 C, TIME : CONT, FORM: KJM"?
Thanks
Reply
What's the warranty conditions for this pump?
Reply
Hi, Dan J. To view the warranty terms and conditions, see the Motor Warranty Video.
Reply
I am in California and have a Century Centurion CAT B859 Part 7 -177217 - 25 2 HP. Is there an alternative drop in replacement?
Reply
Peter, If you live in California, you will need to replace your single speed motor with a 2-speed motor in order to be in compliance with your local laws. You can replace your B859 with the B985. Please note that the B985 motor will only operate on 230v. You will either need a 2-speed switch or a 2-speed timer to operate the high and low speed. Also, be sure to change your shaft seal when you replace the motor.
Reply
Hello: I need to replace my current pump that is a square flange 1.5HP Century C48D43A04. I wanted to try to get an upgraded replacement as I wasn't happy with the performance of my current one that has gone bad in just over 3 years. Would this (A.O. Smith 2 HP, 56Y Frame, Up-Rate Motor 230/115 (B859, B2859) pump be compatible with my current pump? Thanks very much! Rich G.
Reply
Good morning, based on the number provided C48D43A04 the A.O. Smith 2 HP, 56Y Frame, Up-Rate Motor 230/115 (B859, B2859) would be the correct motor. One thing to always keep in mind is changing the shaft seal and or the seal plate of the pump.
Reply
Is this the right replacement for 7-177452-03?
Hello, This will be the replacement you will need.http://www.inyopools.com/Products/00200017039449.htm
Reply
Have AO Smith 177476 motor which has sadly expired. What will the California idiots allow me to replace this with?
Thanx - Steve
Reply
You can use either a dual speed motor part number B983 which can use a toggle switch which is listed in the product details or you can use a dual speed timer for it being part number T106R. Lastly, you can also use a variable speed motor part number ECM27SQU which will not any toggle switch or secondary timer.
Reply
I have Century Centurium 2HP Motor that I was replacing and busted the white plate that the wires attach to. The motor works perfectly but I can't seem to find a replacement part to fix this problem. I would like to keep the motor for a backup. The Pump Serial# 31615CH. Part # 177897 Frame # Y56Y
I think what I broke is called the Terminal Board Switch????
Reply
Hello, Unfortunately, we would not carry that part on our website. We recommend contacting the manufacturer to get a part number on that piece. You can reach them at 937-667-2431.
Reply
Hi: can you let me know any less expensive replacements for the B2859 motor? I live in Fl. Also, any reasonably priced pumps that would fit this motor? My PHPM2.0 pump needs replacement too. Thanks
Reply
Unfortunately, we do not have any other cheaper single speed motors for a replacement and I would consider the Pentair Superflo series pump for another complete pump option that can use that motor.
Reply
I am looking for a replacement motor for a Pentair Pump CF II N1 2A / 343240 with a motor # of 168454. Can you tell me which one you sell? Also, what seals, etc. should I replace when replacing a motor?
Hello, This will be the motor you will need,http://www.inyopools.com/Products/00200017046291.htmThis will be the seal kit you will need, http://www.inyopools.com/Products/00500000040110.htm
Reply
I currently have this motor (well, its equivalent - Mod# 193987) installed on my pump, but it died. This is my second dead motor in 6 years. Our original one was a variable speed and I'm thinking it might make more sense to go back to that kind, but I'm not sure what the variable speed equivalent is for this. Can you suggest something?
Reply
I have an AO Smith motor part O-193987-24 Serial 18910CH that died.
What motor do I need to buy to replace it? Can I buy a 2 speed motor instead?
I have a Century Centurion, A.O. Smith 2HP motor, part # O-193987-24 which I believe is the same as a B2859. The bearings are getting loud and I would like to replace them. I have not been able to find the part number for these bearings, can you help out?
Reply
Hello, is there a CAT number on your motor? This is the only number I can use to locate the bearings. If none is available, I cannot provide the proper bearings for your motor.
Reply
do you have this pool pump motor
AO Smith Part # 0-193987-24
Reply
Yes, we have this motor in stock and ready to ship. Motor orders are guaranteed to be delivered in three business days in the continental US. Holidays and weekends not included. The B859 is the correct single speed motor replacement for your model.
Reply
I have a 2hp Pentair whisperflo 9 years old and the motor has begun to get loud and squeal but still works. I have seen where people replace the motor bearing and then all the seals at put it back together. Do you have the bearing for the motor (Pentair model 177476) as well as all the seals ? Also if you recommend replacing the motor can you send me your part numbers for the motor and all the seals ? Thanks
G
Reply
Hi, Gord. The replacement bearings for your motor are P/N 62032RS (OSE) and 6304 (SE). This B859 is the correct replacement motor if you choose to replace it. Whichever option you decide to go with, you will also need the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
Is there a bearing kit that I can buy to replace the motor bearings or would it be easier to buy a new pump motor? If buying new, which motor would be the best replacement?
I currently have a 7-77476 century motor on my pentair whisperflo WF-28 pump that's getting loud from bearing noise. I've can you tell me what bearings fit in this motor and if they are different sizes which one goes on front verses the rear of the motor? Additionally, what would be a suitable replacement?
Thanks
G
Reply
what is the correct shaft and diffuser seal for jandy pro series plus HP serial V16FA0205. Model PHPF1.5 motor is b2859. What seals are recommended when changing out a motor?
Reply
Hi Bill, You will require this Jandy PHPF Plus HP Shaft Seal and this Jandy PHPF Diffuser O-Ring Kit
Reply
hello, my pool pump motor is squealing and probably needs to replaced. it is a centurion 7-193994-06 for a jandy stealth pump. What motor should i get and what other parts are necessary to replace it? I appreciate your help. thanks!
Reply
Hi James, yes this is the correct replacement motor for your motor part number 193994. When replacing a pool motor we do suggest a seal kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. We will also need the serial number. To supply photos simply click the reply link below and upload your photos or quickest using our live online chat feature. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Hi,
I walked out to my 3 year old pool pump today to see that the breaker had tripped. When I reset it and the pump tried to start it just made a loud menacing buzz so I shut it off quickly. The motor housing is very hot. I believe this motor is the correct replacement but I would like to confirm before ordering. Please see attached pics. Also, I was thinking I might want to test the motor by detaching the pump section to see if maybe the pump is the problem.
Hi Rob, yes this is the correct replacement motor for your motor included in the photo. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or provide them quickest using our online chat feature. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Is this the correct replacement for my seized Century motor on a Jandy? Also what other seal kit would be required? Thanks!
Yes, the Century 2.0 HP Square Flange 56Y Up Rate Motor - B2859 is correct for replacing the motor in the image with part number 7-193987-24. The pump model on the labels also confirms PHPM2.0 this pump offers different shaft seals, you will need to verify the serial number on the wet-end of the housing to select the correct shaft seal shown here http://www.inyopools.com/pool_parts_jandy_plus_hp_2006_current.aspx The Backplate O-Ring R0446300 and Diffuser/Impeller Hardware - R0446500 should be replaced too.
Reply
I have a O-193987-24
TYPE CX
FRAME Y56Y
What is a replacement that will fit? Do i need to replace anything else at the same time?
Reply
Hi Michael, this is the correct single speed replacement motor for your motor part number 193987. It is also recommended to replace the seals when replacing a motor. We would just need to know the model name or number of the front pump wet end housing the motor attaches to in order to locate those for you. You can also upload images of that in a reply here if you need.
Reply
Would this be the correct replacement pump motor? What would be the correct bearings to replace in my current pump? What’s the correct seal kit, I have a salt water system? Thank you.
You are correct; the B859 is the replacement motor for your part number 196240, which is mounted to the WhisperFlo WF28.
Reply
Hello. I am looking for the bearings and GOKIT for my Century 5P3215Z1M pool motor (1081 pool pump duty). This is part number: 7-56AA13A04-25
HO 2.00
SF 1.10
FR Y56Y
VOLTS 230/115
I notice the motor making a loud noise so we would.like to replace the bearings and since there is a leak we need the shaft seal and gaskets. Do you sell these parts? Which ones are the correct part number please? Thank you
Reply
Hi Adriana, the 6304 (front) and the 6203 (rear) are the replacement bearings for that motor part number f56AA13A04. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I need to replace a 2HP pentair 177476-20 pump motor. Y56 square frame. 3450 rpm 230/115v 11.2/22.4a. It may be a 20 years old.
All the specs seem to align with the B859 except they all say the 2 HP has a service factor of 1.0.
BUT The label on my motor says the service factor is 1.15. So a 2hp x 1.15 = 2.25 HP. I think I need to upsize the replacement to meet the 2.25 effective HP. The 2.5 HP replacement its only the 230/240v not duel voltage.
Do I go with the B859 or upsize?
hello, based on the information we would recommend staying and going with the Century 2.0 HP Square Flange 56Y Up Rate Motor - B2859. It will be the unit that is closest to the 2.25 THP.
Reply
What is the difference between replacement Century A.O. Smith B859 and B855 Square Flange 2 HP Up-Rated 56Y Pool Motor?
Reply
Hello Barbara, the Century 2.0 HP Square Flange 56Y Up Rate Motor - B855 would only be wired at 230 the Century 2.0 HP Square Flange 56Y Up Rate Motor - B2859 could be wired either 230 or 115.
Reply
What replacement bearings and seals kit do l need?
The B859; You would need two 203 Motor Bearings. We do have these two Bearing Videos which should help you out when you tackle this project. Video #1 How to Replace Pool Motor Bearings and Video #2 How to Replace Pool Motor Bearings. The Pump Shaft Seal 5/8" - PS-1000 or PS-3865 Heavy Duty for Saltwater Pools. Frequently Bought with this Shaft SealClear RTV Silicone 6558-0 (For gluing shaft seal into the seal plate)
Reply
What replacement bearings and seal kit for a Century 2.0 HP Square Flange 56Y Up Rate Motor.
Thanks
Barb
Reply
Hi Barbara, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
Hi I need a motor, impeller, assembly kit for this pump.
Hi Arturo, You will require this WF-28 Whisperflo 2 HP Replacement Impeller and this Whisperflo Seal Kit
Reply
Hello! Is this the correct replacement motor that I need? My current motor looks like it could be older everyone else that have posted so far because I cannot find an exact match to what I have, but a few have posted very similar motors to what I have. Any help would be very appreciated.
3 pics included
1. Pentair Label containing Part # and specs
2. Small Label showing HP, SF and SFHP
3. A.O. Smith / Century Label
Hello. The Century Motor Single Speed model B2859 is NOT a replacement for your Century Dual Speed 1.65 SFHP motor. The Century Motors 1.0HP (1.65 SFHP) Dual Speed Full Rate Motor model B2982 is a compatible replacement. It is recommended that the motor shaft seal, seal plate gasket, and diffuser O-ring be replaced at the same time. If your current Pentair pump is a Whisperflo, the GOKIT32 contains these parts. If your Pentair pump is a Superflo, the GOKIT78 contains these parts. Century 1.0 HP Square Flange 56Y Dual Speed Full Rate Motor - B2982 Tune Up Kit Pentair/Purex Whisperflo - GOKIT32 Tune Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78
Reply
Hello. Is this the correct motor I would need for a replacement? Also would I need anything else? Thanks
Is this the right replacement motor for this Pentair SuperFlo #196240
Yes, the Century 2.0 HP Up Rate Motor - B2859 is a perfect replacement for the motor on your Pentair SuperFlo pump. Be sure to get this Tune Up Kit Pentair SuperFlo - GOKIT78 which contains all of the o-rings you will need as well as a new motor shaft seal to ensure a leak-free installation.
Reply
I need to replace the motor on my Jandy FloPro 2HP single speed pump. Is this the correct part?
Hello Kevin. The Century Motors 2.0 HP Up Rate Motor model B2859 is the correct replacement motor for the Century Motors model 193987 installed on your Jandy FloPro Pool Pump FHPM Series. It is recommended that the motor shaft seal Pump Seal Backplate O-ring and Diffuser O-ring be replaced concurrent with the new motor. Diffuser & Impeller Hardware
Reply
PHPM Hello, I'm looking for replacement bearings for my motor pump Part- 0-196159-06 / Frame Y56Y / rpm 3450 / volt 230 /serial 18910CH
also, what seal kit do you recommend for pump model PHPM2.0 / serial R09F_0736 (best I could read)
Pic. Attached
Thanks in advance
Hello Cesar. Attached please find an exploded parts diagram for the Jandy PlusHP PHPM Pool Pump Series. Jandy PlusHP PHPM The motor shaft seal, Key #5, R0479400 is the correct seal for pumps with a serial number P08FF0001 & After. Jandy Pump Shaft Seal It is recommended that the Backplate O-Ring be replaced concurrent with the new shaft seal. Backplate O-Ring, Bearing information for the motor 0-196159-06 is not published by the manufacturer. This information is available from the manufacturer. Attached please find a link to Regal Rexnord, manufacturer of A. O. Smith/Century Motors Regal Rexnord
Reply
My motor runs for a few minutes and then shuts off. It does this all day long, on for 5 mins, off for a few mins. I changed the mechanical timer, no difference. I changed the motor capacitor, no difference. Do I need to replace the motor or are there other parts that might be causing this? If so, is this the correct replacement for the motor? And what seals, etc. do I need to complete the swap? Thanks!
Hello Andrew. The circumstances described are typical of a motor overheating and engaging the Thermal Overload. Attached please find a brief tutorial Troubleshoot Pool Motors Please note section - Protector (Thermal Overload) The compatible motor replacement for the Pentair motor 196251 is the Century 2.0 HP Square Flange 56Y Up Rate Motor - B2859 The GOKIT5 contains the parts necessary to install the new motor on the Pentair Challenger model CHII N1 2A.
Reply
Hi, would this replace an older A.O. Smith Centurion Switchless Motor part # 7-193987-24, 56y, 2HP, 230/115 volts, 11.2/22.4 amps? I can’t make out the actual model number on the motor. This one says 10.5 amps so not sure if it’s suitable? I’ve attached some photos w rhe specs of iur current motor. Thxs!
Hello Shane. The Century 2.0 HP Square Flange 56Y Up Rate Motor - B2859 is a compatible replacement motor for the Centurion Motor model 7-193987-24. The Jandy Pump Shaft Seal and Backplate O-ring should be replaced concurrent with the new motor. Attached please find the Jandy FloPro FHPM Series Pump exploded parts diagram for the model FHPM2.0.
Reply
My pump is completely dead. Can you tell me which pump motor and seals I need to replace my current one? I can’t find the SF number on any label. Thanks.
Hello Justin. The Century 2.0 HP Square Flange 56Y Up Rate Motor - B2859 is a compatible replacement motor for the Pentair motor 7-177476-20 (2.0 HP, 1.1 SF) installed on the Pentair WhisperFlow WF-28, 011774. The Tune Up Kit Pentair/Purex Whisperflo - GOKIT32 contains the seals and gaskets necessary for the new motor installation. Attached please find the Pentair Whisperflo Pump exploded parts diagram for reference.
Reply
Good Afternoon,
Is this a direct replacement for the pump shown in the picture. If so what other pieces are needed IE gasket kits.
Thanks in advance,
Dan
Hello Dan, yes this is a compatible replacement motor for your motor model 177476. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Your seal kit would be the GOKIT78. Here is a general guide we put together called "How To Replace Pool Pump Gaskets" that also may offer some guidance for this job.
Reply
