What is Service Factor?
Reply
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
Reply
Why do I need to purchase a new shaft seal?
Reply
We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
Reply
Why should I purchase a Tune Up Kit?
Reply
A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
Reply
I'm trying to replace the motor on my pool pump but all these numbers and abbreviations on the motor label are really confusing me. What do they mean?
Reply
Replacing a pool pump motor is not as difficult as it seems. You can try looking here. If you need help figuring out what the information on your label means. If you are still having difficulty figuring it out you can call us at our toll free number or you can send us a photo of your motor label here.
Reply
I just finished replacing the shaft seal on my booster pump. As soon as I turned the pump on water was leaking from the shaft seal. Is it defective or am I doing something wrong?
Reply
Depending on the model, the installation of a booster pump shaft seal can be slightly different than a pool pump shaft seal. Some booster pump and pool pump shaft seals require that a silicone sealant be used on the outer areas of the metal seat of the shaft seal. The seal will need to be lightly hammered into the body of the pump. You can use a 1 inch PVC coupling or a piece of 1 1/4 inch PVC pipe and a rubber mallet. This procedure will apply to any pool pump or booster pump using a >PS-1000 style shaft seal.
Reply
I have a 1.5 hp whisperflo single speed pump. The motor is humming loudly and going out. Would using a 2hp motor increase the life of the motor or help with the water movement or does it spin faster thus causing a higher output? Thanks!
Reply
Aaron, Increasing the HP wouldn't necessarily increase the lifespan of the motor. Also keep in mind that the higher HP means higher amps (higher electric bill). Upgrading the HP would also mean needing to upgrade the impeller. You also want to check that your filter can handle the higher HP before making a decision.
Reply
I need to replace (not original motor) an AO Smith B2854 1.5hp motor. This motor only lasted 3-4 yrs. Is there a better replacement out there?
Reply
Hello Dennis - We would recommend a 2-speed motor. Running the motor on the low speed will extend the life of the motor. Model B2982T would be the correct replacement. This is a full rated 1HP motor but it has the same total HP of your motor (1.65).
Reply
I need to replace a pool/spa motor. I replaced another one two years ago and this one is identical. I need at least a 1.5 HP and the serial number was 22612CH0614638 and the model is B2848. I see one in your catalog online but the model # has changed to B2842. What is the difference?
Reply
Does this motor comply with the California Title 20 requirements?
Reply
Terry, California’s Title 20 legislation states that pumps > 1HP (total) must be 2-speed or variable speed, and must have a control to default to low-speed (i.e. timer). We do carry the 2 speed version B2983T.
Reply
Thanks for the response; would the VS model ECM16SQU also be compatible? (I'm not sure about SF x HP) and is there a recommendation for one or the other of these two?
Reply
Yes the Variable Speed Motor ECM16SQU is also be compatible. If your pocket book can support it we would suggest the variable speed motor as it will save you quite a bit on your operational costs. We recently wrote an article on Is a Dual Speed Pump or Variable Speed Pump Right For Me. This article should help out quite a bit on determining which route you would like to go.
Reply
Is this a replacement or fit for a Pentair Super flow Pump 1.5 HP .
Reply
It can be used on the Superflo but we would need the specific pump model to cross reference your exact motor replacement.
Reply
My pentair pump just literally burned out....smoke and all. The part number on the motor is: O-177451-03
Is this a direct replacement part? just take other off....then mount and bolt this one?
Is there a warranty??
Reply
Hi Kris, The A.O. Smith 1.5 HP Motor EE Full Rate (B2842) would be the direct replacement for p/n 0-177451-03. These motors comes with a 1 Year manufacture warranty.
Reply
I want to replace my burned out motor with the energy efficient version. My original pimp motor number is 7-168454-25. Is this the correct high efficiency replacement motor?
Reply
Hello Anthony - The B842 (B2842) is the correct energy efficient replacement motor for your 7-168454-25 (B858).
Reply
What is the expected lifetime and warranty on this pump?
Reply
Hello David, All Century® motors are warranted against defects in materials and workmanship for a period of twelve (12) months. Lifetime of motor will vary depending on elements, location, run time of the unit.
Reply
What is the direct replacement for
7-177451-03 A.O. Smith Century Centurion
Reply
The correct motor replacement for the 7-177451-03 is the B842. Do not forget to purchase a shaft seal or replacement kit to complete the motor installation.
Reply
my polaris' booster pump stopped working. its 11 years old. its a AO Smith Cat B625, Part 8-173840-23 which motor would be best to replace it? Do you have videos of how to swap out the motor?
Reply
What is it about the B2842 that makes it energy efficient? The amps seem similar (or greater) to one that is listed as standard efficiency. Doesn't the formula apply the same in both instances (amps X volts = watts?) Wouldn't both types of motors use the same amount of kilowatts? Thanks!
Reply
Our pool pump burned out and we're trying to match the model. It's a Marathon Electric Mod. 5KC38SN6084AX. 1.25 HP, 115/230v, 3450 rpm, We checked, and this model is no longer manufactured. Any idea what model we should get to replace this motor? Energy efficient is always a plus. Thank you.
Reply
Hi Adalton, The A.O. Smith 1 HP Up Rate EE Motor (B863SE) will be the energy efficient replacement for the 5KC38SN6084AX motor.
Reply
I have a 17 yr old Magnetek Century Centurion B842 (1 1/2 hp) that I'm looking to upgrade to a more energy efficient model, but I need to maintain a certain psi (15 I think) for my Paramount PCC200 floor nozzles to operate correctly.
Do you have a recommendation?
Reply
Hi Frank, The B842 is the is an energy efficient 1.5 hp full rate single speed motor, there is not a more energy efficient simple speed motor.
Reply
I am looking for motor AO Smith Part 7-K56AA23A04-05 or something comparable. 1.5 HP Dual speed. Can you help.
Reply
A direct replacement dual speed motor consistent with model #7-K56AA23A04-05 will be the Pool Motor Square Flange 1.5 HP Full Rate Dual Speed w/ Digital Controller - B2983T.
Reply
Need to replace my MARATHON 5KCR39SN2823AX pool pump and I am wondering which one Energy Efficient will fit (I mean just remove and install a new one) ... My current is HP 1.5 - V 115/230 - RPM 3450 ... Thanks.
Reply
Jorge, There are additional specs we will need to confirm. Please provide the SF and amps of the existing motor. If you are unsure, you can email a picture of the existing motor label.
Reply
My pool motor is howling. She is a Century Centurion AO-Smith E-Plus.
Ser # BX7-01
Part # 7-177451-03
1.5 HP
I am looking for a replacement. She is a single speed motor and willing to look at motors that are a direct fit or another Century Centurion. I am wanting something as good or better.
Thanks.
Bruce.
Reply
Hi, Bruce. The B842 motor is a direct replacement for p/n 7-177451-03 which is also a Century motor. Century is the only manufacturer of motors that we carry.
Reply
Will this model replace a Magnatek motor, MODEL: WFE-6 part: 10-177451-03 SF: 1.47 TYPE: CX VOLTS: 208-230 AMPS: 9.6-8.8 RPM: 3450 FR: Y56Y
Reply
Yes that is the correct motor replacement. The gokit32 would be the seal kit needed and the gokit32salt if you have a salt pool.
Reply
I have a Cat. B842, Part 10-165200-06, FR Y56Y, SF 1.47, HP 1.5, Volts 208-230, Serial BS2-02, 1081 POOL PUMP DUTY MOUNT HORIZ WITH VENT HOLES DOWN. Will your motor replace this one including the vent holes down?
serial1081 Pool Pump Duty Mount Horiz With Vent Holes Down
Reply
Yes, the vent holes are on the bottom of the motor.
Reply
Hello. This has a one year manufacturer's warranty. Since you sell to DIYers how is a warranty issue handled in event of an issue during the 12 month warranty period?
Thank you,
John
Reply
Hi, John. If the motor fails within the 12 month period, you would call us and we will provide you with the information that we will need in order to submit the warranty claim.
Reply
Can this (1.5 HP Motor EE Full Rate (B2842) motor replace my A.OSMITH Cat B855 Part 7 177897-22. TYPE CX FR Y56Y HP 2.0 SF1.10 HZ60 RPM3450 VOLTS 230 AMPS SF 10.0
1081 POOL PUMP DUTY MOUNT HORIZ WITH VENT HOLES DOWN?
I do like to have a EE Motor.
Reply
Hello- Yes, you can replace the A.O. Smith 2 HP, 56Y Frame, Up-Rate Motor - B855 with the 1.5 HP Motor EE Full Rate (B2842).
Reply
hi, i need to replace my old magnetek century motor, part number 8-177451-03. would this be the correct replacement motor
Reply
Hi, Mark. Yes, the B842 motor is the correct replacement for p/n 8-177451-03.
Reply
I need to replace a Pentair 1.5 HP motor on WhisperFlo WF-26 which is 10 years old. Part # is 7-177475-20. Will this pump work?
Reply
Good day, the motor you are going to need for the WF-26 would be 1.5 HP Standard Motor - Full Rate (B2858). If you wanted an Energy Efficient model that would be 1 HP Motor EE - Full Rate (B2841, B2841V1). Keep in mind we recommend to change the seals and gaskets in the pump. Which would be our GOKIT32 or GOKIT32Salt for salt water pools.
Reply
Hi, I need to replace a pentair pool pump 177450 motor. However my pool-man suggested a more powerful motor 1.5 HP. Would this motor work? Please include any suggested parts
Reply
What model of Pentair pump do you have, you will probably have to upgrade your impeller as well if you up the horsepower?
Reply
the pump model no is WFE-4 Does it need to be replaced along with the motor? Please clarify
Reply
If you go from a 1HP motor to a 1.5HP motor you will need to upgrade the impeller as well to part number 5074-27C.
Reply
Hi I need to replace a pump B842 Part 8 -165200- 06 . Is this the right replacement?
Reply
Hello Jim, the B842 and B2842 is the same unit. Yes this is the correct replacement for 8-165200-06.
Reply
I have a 1 year old ecopump with a dual speed century b2983 motor. The motor died. Can i replace it with this motor and simply run on one speed?
Reply
Yes that would be a suitable replacement single speed motor for you. Please consider replacing the seals as well. You would need to know the model of the front pump housing the motor bolts to in order to cross reference the seal kit.
Reply
I had a whisperflow pump which I thought was 1.5 HP and i see I have a Pentaire pump of.75HP and is a smaller motor. my pool is 15/30 inground. what size motor?
Reply
Hi Ralphj, Could you send us a photo of your motor label as well as a wide shot of the complete pump? You can simply reply to this email with those photos or send them to upload@inyopools.com
Reply
can this go on my 011773 whisperflow...What motors can go on this 01773 whisperflow ?
Reply
I have an AO Smith 7-F56AA12A04-24. Is the B2842 the correct replacement? It looks like it is but I am unsure of the shaft diameter being the same.
Reply
Hi, Randy. The Century B854 Motor is the correct replacement for p/n 7-F56AA12A04-24.
Reply
Will this EE motor replace my current one? It's a Purex Triton Challenger, motor is 1.5HP/SF1.1 56Y. Centurion 168453-24 part 7. Also, which tune up kit do I need and how do I get 72hr shipping as advertised? Thanks!
Reply
Hi Nancy, You will require the B2854 1.5 HP Up Rated Challenger Replacement Motor when replacing your motor we would also suggest this Challenger Seal Kit.
Reply
It looks like it but just making sure it will replace my Century HSQ125. This old one is consuming allot of electricity, its still runs fine.
Reply
Sirs:
I need a replacement motor for a large waterfall feature. The present pump is an A.O. Smith catalog # B842; part # 7-165200-06. Is the B2842 the correct replacement?
Thank You
Reply
Jim, Yes, the B2842 is the correct replacement motor for the B842.
Reply
I have the following and am looking for a replacement....a bearing (or both) are grinding:
Century Centurion, AO Smith
2HP; 1.1SF
Serial - BW 12-18
PN 7-177451-03
60Hz; 3450 rpm; Type CX; FR Y56Y
This then connects to my pool with a threaded spring clamp; it connect to Model 38469800, Serial PF-1-30-A02
I there anything else that I need with the motor to replace?
Reply
Hi, Mike. This Century B2842 Motor can be used as a replacement for Part # 7-177451-03. You will also need the Ultra Flow Tune Up Kit - GOKIT20.
Reply
I purchased a SQ1152 motor back in 6/20/2011 order number 321513. It is overheating now and it seems like there is no air blowing out of the cooling vents located front and back of the motor. I also noticed something white, round with a hole in the middle that would go around the shaft. I was really expecting a longer lifetime for the motor. Is there a higher quality form / fit / function motor that I can order?
Reply
Will this pump, 1.5 HP Motor EE Full Rate (B2842) work as a replacement motor and everything lines up correctly?
I have a 2HP SF HP 2.2
Model 196251
Part 343240
For a Pac Fab pump
Reply
Hi. Yes, this B842 1.5 HP EE Full Rate Motor can be used as an alternate replacement for your Challenger CF 2 HP UR Pump - 343240. You can also use the B855 - 2 HP, 56Y Frame, Up-Rate 230V Motor or the B859 - 2 HP, 56Y Frame, Up-Rate 230/115 Motor.
Reply
Because I'm going from a 2HP motor (B8555) to a 1.5 HP motor (B2842) will it match up correctly? Will I need to change out the propeller? What is the correct seal kit?
Reply
This motor will match correctly and you will not need to change the impeller. In order to cross-reference the correct seal kit, we will need to know the model name or number of the front pump housing that the motor bolts to. You can call in with that info or if you are not sure you can always send a picture of it to upload@inyopools.com.
Reply
Will this replace A.O.Smith part 7-193994-06, 3450, 1.5 hp, 208-230 , 9.6-8.8, 56Y?
Also will I need a seal kit? My pump is a Jandy Stealth Series Model SHPF.
Thank you.
Reply
Hi, Tamra. Yes, this B2842 motor is the correct replacement. There is not a seal kit available for that model pump. The pump shaft seal and other o-ring will have to be purchased separately. The can be found using the Jandy Stealth SHPF & SHPM Parts Diagram.
Reply
I need to replace a 1 1/2 pool pump motor for a hayward model # sp2610x15 , 115/230 volts
Reply
The proper replacement motor for the Hayward SP2610X15 Super Pump is the UST1152 1.5 HP Super Pump Replacement Motor. You will also need a Super Pump Tune Up Kit when you replace your motor. We also have a Video on How to Replace a Pool Pump Motor which you may find handy when you tackle this project.
Reply
A O Smith (#B2842) 1,5 hp AC electric motor for the pool pump. Want to change over to a DC Motor HELP!!! Pump is still good.
Reply
Hi, Peter. Unfortunately, we do not carry DC replacement motors.
Reply
I have a Sp2610X152S pump with a Century Sp-1610-Z2-MSC motor. The bearings are going bad and need to replace the motor only. Can you suggest a replacement?
Reply
Hi, Dan. You can replace the motor only with the STS1102RV1 motor along with Super Pump Tune Up Kit - GOKIT3 or GOKIT3SALT
Reply
I need a replace motor for my Pentair pool pump. It is Century Centurion Part 7 -177451-03 Type CX FR Y56Y Serial: BW9-14 TIME CONT CODE H PENTAIR MODEL WFE - 6 SERIAL #: 11 01 1330 AP. Can I use this motor to replace my current defected motor. Thanks. David
Reply
The B842 is the replacement motor for your model 7 -177451-03.
Reply
what will replace challenger high flow pool pump motor 1.5/.25HP 1.10SF part # 8 177144 ( 2 speed )
Reply
I need a replacement motor for WhisperFlo Model WFE-6 pump.
The current motor is A O Smith Century Centurion. serial BZ09-28
Part 7 - 177451 -03. Type - CX. FR- Y56Y. Time - Cont. Encl - DP Form - KJM
Thank you
Reply
Hi, Norm. This B2842 - 1.5 HP EE Full Rate Motor is the correct replacement for the WhisperFlo - WFE-6 Pump. You will also need the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
i have a century centurion A.O. SMITH, serial # BZ04-20, PART 8 -177451 -03, Is this the correct motor replacement and does it come with seal kit? Please advise, Thank you JJAG
Reply
Would this pump be a good replacement for a Pentair 011774? Also with this being an energy efficient model how much of a savings over the 011774 could I see? Last question would if be more economical (energy usage) to go with this motor, or a full-rated 2HP model?
Reply
Hi. This B2842 is an energy efficient replacement for model 011774. You can save approximately 15-20%. This motor will be the most economical option. You will also need the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
I have a Jandy Stealth pool pump model: SHPF1.5
I need to replace my pool pump motor.
My pool motor is A.O. Smith part # 7 193994-06.
Is the B2842 the correct pool pump to replace with?
Also, after reading your blogs I guess I need a tune up kit. Can you help me determine which kit I need?
Yes, this is the correct single speed replacement motor and for cross-referencing the correct seals needed please click here to view the parts diagram for the pump. Most commonly keys 5, 13 and 15 are replaced. You will need the serial number of the pump to confirm which shaft seal that you will need.
Reply
I recently submitted a question and have an additional question. My pool pump is the Jandy Stealth SHPF1.5 (pic attached). The motor on it is an A.o. Smith. The replacement for the motor is the B2842 but based on my pool pump it says the replacement motor for that pump is B2854. Not sure if the motor that is on my pump now is correct. The biggest difference I see is the total horse power. Which replacement motor should I buy?
B2842 is the direct replacement of my motor per previous discussion. Before I place the order, can you confirm that I will be getting unused brand new pump motor with quality inspection blue ink stamp on the face of the motor?
Reply
Hi. The motor you will get is a brand new motor and unused.
Reply
B849 replacement options?
Reply
Can i replace a B2842 motor with B855 motor?
Reply
Hi, Carlos. Yes, you can use the B2855 motor as a replacement for a B2842. FYI, The B2855 motor will use more energy than the B2842 motor leading to a higher operating cost.
Reply
will this pump work with Challenger system? Replacing B855a. Does EE rating have effect on operating capability?
Reply
i need a gasket also ?
Reply
Could you let us know which gasket you need? Also if you could take a photo of your complete pump showing where the plumbing goes in and out of the pump that would help us determine the proper gasket you need. To send photos simply click on the reply link below to upload your photos.
Reply
Would you be able to give me the part number(s) for replacement capacitor(s)? A run and a stop capacitor?
Century Centurion Part 7-193994-06
Part # B842
I think i should try them before replacing the entire pump.
Reply
The motor mfg's do not provide a breakdown list of what motor has what capacitor inside, you will need to look at the capacitor & read the MFD or UF # ( example on run capacitor 40 MFD +- 5% , start capacitor 53 -64 mfd )
Reply
1. Will this motor work with a whisper flo WF-4 pump? Do i need a new gasket kit?
2. My current WF-4, is old and showing signs of wear. Should I replace replace the WF-4 as I replace the motor?
If so do you have the WF-4 /motor combination?
My pond pump motor recently quit and I need to replace it; The nos. are A.O. Smith Part No. 7-196337-20, CATHSQ1152 Serial No. 046103M 1081 Pool Pump Duty.
I have older model Pentair Intelliflo VSP (pre-2011). The drive is apparently going out - won't maintain correct pressure regardless of setting. The drive is no longer available for this older model. I was told that I could replace existing pump motor with this one, thus avoiding cost of new drive. Given the age of the pump, the motor likely does not have much life left either. I have ~24K pool. Will this pump motor work?
Reply
Hi Kevin, Could you let us know which state you are in? If you live in California you now have to go with a VSP. Also could you give us the information off of the motor for your current pump like HP, Amps, Volts, SF, Frame, Model #, etc..To supply this information click the reply link below, also if you could send a few photos those are always helpful as well. If you send photos then take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get any of this information we can make the proper recommendation.
Reply
I live in Houston, Texas, not in CA. I have attached photo of the pump label. Info as follows: Volt: 230, PH 1, KW: 3.2, Amps: 16, SF: 1, Frame: 56; Part No. 353214
Hi Kevin, Thanks for the photo that was quite helpful. You can switch to this motor and you will also need to switch out the following parts 1.) 1.5 HP Whisper Flo Impeller 2.) 1.5 HP Diffuser 3.) Whisperflo Seal Kit
Reply
Hi, l like to replace my Pentair motor part# 7-177451-03, 11/2 HP, 3450 RPM. For Whisper Flo WFE-6 pump.
What motor i should use?
Thanks
Reply
Hi Mark, Yes this is the correct replacement motor the motor included in your photo. You will also need a Pentair Whisper Flo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I need to replace my Pentair Motor and can’t match my motor #177450 with your inventory. Please advise which Pentair Motor I should order to replace my current one.
Reply
Please provide a picture of your current motor's label.
Reply
Hi, I have a Century Centurion A.O. Smith 1.5 HP 1.5 SF pump that burned out on me. Is this motor compatible with it (I noticed subtle differences like 1.47 SF instead of 1.5, etc. (see the picture I'm attaching) and wasn't sure if any of them were significant enough for it to not be a match)? And it sounds like I should be replacing the shaft seal (anything else?) too? What part would I want for that? Or is there a different better motor I should be switching to, like 2-speed or something?
I just want to verifiy: I have A.O. Smith motor:
Serial# 181093M
Part#7-193994-06
Pump:
Jandy Stealth
Model#SHPM2.0
SERIAL#R09FH2463
2HP
i just need to know your correct replacement motor and the seal needed to go with it? Thanks
Reply
Hello - the drop-in replacement motor is the A.O. Smith 2 HP Square Flange 56Y Up Rate Motor - B2859. Also, your Jandy SHPM requires the JANDY SHAFT SEAL OEM (NEW STYLE), according to your serial number.
Reply
Is this the correct replacement motor for a Pentair Challenger High Pressure pool pump (345206)?
Reply
Hi, Paul. Yes, this B2842 motor is the correct replacement. You will also need the Challenger (CH Series) Pump Tune Up Kit - GOKIT5 or GOKIT5SALT.
Reply
What is/are the part number(s) for the bearings that fit this motor?
Reply
The B2842 motor uses two of the 203 (62032rs) Bearings.
Reply
Is this the EE choice for CFII-N1-1 1/2A? Or, would a Pentair model be better?
Is this the correct replacement part for pentair177451
Hi. Yes, this B2842 is the correct replacement. You will also need the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT
Reply
I broke the metal tab on the rear motor casting (see pictures) at the electrical service entrance. Can I order this part from you? I cannot locate a schematic that shows this part so I can't provide a part number. I tried to fix it using epoxy but I have no confidence it will hold.
Thanks!
Jim, we apologize for the inconvenience, however, we would not have these parts available. We would only have the whole motor. We suggest contacting the manufacturer directly to see if they can point you in the direction of a supplier for these parts. AO Smith/Century can be reached by calling 866.887.5216.
Reply
This is not a replaceable part.
Reply
We are sorry but that is not a replaceable part on the motor.
Reply
I need to replace my B849 motor and it looks like this is a more energy efficient replacement but just want to be 100% that this would be a direct replacement for the B849 with no problems or changes
Reply
My pool pump has recently become much louder. It sits outside, runs 6 hours a day, and has been in service since 2002. I suspect it may be getting near the end of it's life. It is an A. O. Smith Part # 7-168787-07. Frame Y56Y
3450 RPM Type CX 208-230 volts 9.6-8.8 amps. Do you have a replacement for it? I would be interested in a more energy efficient motor if possible. Thanks, Lewis
Reply
We have a old Magnetok Century Centurion pool motor, the bearings are out, when we run it , it makes a very load
Noise, so we need to replace it. I have taken a picture of the label on the motor to see If the motor listed above will work in place of our old one.
Hi. The B796 or ST1152 motors are suitable replacement.
Reply
Thanks so much for your reply, the pump numbers B796 or ST1152 have round flanges, I need a square flange motor, sorry I should have listed that the first time I sent the email.
I have a pentair pump motor out with burnt bearingslooking for a replacement alternative to a brand name motor. Model number wfds-26. Photo attached.
Hi, Stewart. The B2982 motor along with the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT are the parts you will need.
Reply
This is in response to my post shown here, Per the label shown here my motor is 1.5 hp. The b 2982 is stating it is a 1 hp motor. I’m confused as to this being the correct replacement. Please advise soon as my pool is getting green...UGH!
Reply
The Century 1.0 HP Square Flange 56Y Dual Speed Full Rate Motor - B2982 is the suggested replacement to the Pentair Whisperflo Dual Speed Up Rate 1 1/2 HP Pump - WFDS-26 the total HP on the High of the replacement motor is 1.65HP and low setting is 0.21HP. This meets and exceeds the total HP rating of the current Whisperflo motor on the pump. Please see How To Understand True Pump Horsepower - Up Rated vs Full Rated for the details.
Reply
b2982 motor is a I horse/.13 dual speed correct? the motor I have is a 1.5 horse/.19 dual speed motor. I see there is a 1/2 hp difference here. if I did not want the lower hp dual speed motor and want to go to a single speed would the b2842 be the replacement. Would it bolt up to the pump housing? the motor pictured has been repaired due to burnt out capacitor and only functions as a single speed any way. Stewart
Reply
This motor is no longer a whisper and more like a jet engine. I wanted to make sure that this is the right replacement.
Hi, Joanie. Yes, this B2842 is the correct replacement. You will also need the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
Hi Joanie, I have the exact same pump to replace, did you run into any issues?
Reply
We offer How To Replace the Motor on Your Pool Pump The Whisperflo uses the PSR-1000 pump seals that require a thin layer of RTV Sealant between the metal backing of the pump shaft seal and Seal Plate You may use another guide generic to the Whisperflo pump that shows how to replace this style seal http://www.inyopools.com/HowToPage/how_to_change_the_shaft_seal_on_a_polaris_pb4_60_booster_pump.aspx and other How To Guides http://www.inyopools.com/how_to_guides.aspx
Reply
need a replacement motor for a whisper flo spa pump. motor part # 8-177451-02. I think it is a 1 1/2 hp. the frame is Y56Y form KJM 3450 rpm. volts 208-230 amps 9.6--8.8 S/N BM7-181.Type CX Century E Plus Pool & Spa Duty. Also the part # for the seal kit thanks.
Reply
Hi, David. This B2842 motor along with the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT are the parts you will need for your pump.
Reply
I need a new motor for my pool pump system (STA-RITE P6E6F-207L). Old motor K48M2PA105. What would be the part nuber of the motor and install kitt? Nevada
Reply
Hi Hardy, This is NOT the correct replacement motor for the pump you referenced. You will require this SQ1152 1.5 HP Replacement Motor Based on your pump information you will also need this Sta-Rite Max E Pro Seal Kit. Please note that for Sta-Rite Max-E-Pro models February 2015-Current you will also have to purchase the Seal Plate Gasket - 357099Z if your pump is from before Feb. 2015 then this is not needed. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Is there a dual speed motor with the timer on top available for the same type of replacement? Thank you
Reply
The labels on my Pentaire Pump 1.5HP WhisperFlow has faded and cannot tell the part number. Is the B2842 compatible with my system? I would like to look at other options better then the existing one. I want some energy efficient type but yet not too expensive. My motor is running very low now. I think it is about to die soon. Please tell me what other options that may work better than what I have now. Also, would it hurt for me to go to a 2.0 HP instead? See attached photos.
Hi Mak, The B842 motor on this page is an exact match replacement to the motor in your photo. The most energy-efficient motor will be this 2.7 HP Variable Speed Replacement Motor. Here is an article we wrote on the Energy Savings of a Single Speed Pool Pump Vs. a Variable Speed Pool Pump. If you wanted to take advantage of the higher speeds of the Variable Speed motor then I would suggest upgrading to a 2-1/2 HP Whisperflo Impeller. With either motor you will require this Whisperflo Seal Kit
Reply
I need to replace my Century Centurion pump. The label does not list the HP. I have attached a photo of the label. Can you tell which is the correct replacemnt
Hi Suzi, yes this is the correct single speed replacement motor for your motor included in the photo. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
We are having trouble removing the impeller off the old motor is there a replacement impeller part in case my husband breaks the old one?
Reply
Yes there is a replacement impeller available.
Reply
what # is the replacement impeller
Reply
Hi Carlos, for us to suggest the proper impeller could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? Once we get this photo we can make the proper recommendation for the impeller.
Reply
I am looking to replace my original motor on a Whisperflow Pump, model 7-177451-03 and the B2842 is what comes back, but is only a 1.5 HP motor, whereas the original is a 2 HP. What would the correct 2 HP version be. Also, to confirm, wiring pattern would remain the same. L1 from old motor = L1 from new motor.
Hi Brian, this is the correct replacement motor for motor part number 177451. You will also need a Pentair Whisperflo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project. Also, for 230 voltage each hot lead will go to L1 and L2. Here is a guide for "How to Wire WhisperFlo and Similar Pumps For 115V" and also one that better explains why this motor is labeled 1.5 hp but actually is a 2 hp. It is called "How To Understand True Pump Horsepower - Up Rated vs Full Rated".
Reply
My pump has a round clamp that attaches the pump to plumbing. Is a square flange correct replacement for US Motors #K63CXDFV-5158? Do I need anything else to replace the pump?? Thanks. Brian.
Reply
Hi Brian, Yes this B842 motor is the correct replacement motor for the US Motors #K63CXDFV-5158. When replacing your motor you will need a seal kit. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
here are photos of the connection
Based on the year your pump was manufactured You will need this Sta-Rite Seal Kit Pre 1998 or this Sta-Rite Seal Kit 1998 and After. If you are not sure if your pump is from before or after 1998, then we put together this Video on How to Determine if your Sta-Rite Pump is Before or After 1998.
Reply
Will this motor replace the one in the picture? If yes do I need any additional parts?
Hi Denis, yes this is the correct replacement motor for your motor included in the picture. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
afternoon.
looking to replace pump 7-193994-06, will this work ?
Thank you
Dwayne
Reply
Yes this motor is the correct replacement motor for your motor. When replacing your motor you will need a seal kit. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
Hi, is this a good replacement for my current motor?
Hi Alexandra, yes this is the correct single-speed replacement motor for your motor part number 177451. It is also recommended replacing the seals and gaskets when replacing the motor. In order to locate the correct ones, we will just need the front pump wet end housing model name or number that the motor is attached to. You can also upload photos in a reply to this if you need to.
Reply
Hi, would tthis be a good replacement for my pump.
Hi Alexandra, yes this is the correct single speed replacement motor for your motor part number 177451 included in the photo. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
hi im looking to replace the motor for the attached photo. is this the current unit? also is there a proper seal kit you suggest?
Hi Noman, yes this is the correct replacement motor for your motor part number 177451. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? Please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I have a Century UST 1152 motor that's about to crap out what do you consider a better than average replacement
Reply
Hi Mike, A better than the average motor that will replace this UST1152 would be the ECM16CU. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Will this replace my Magnetek Century Centurion pump number 177451-03 1.5HP? Attaches to a Purex Trtiton Whisper Flo pump. Thank you.
Reply
Hi Brian, yes, this is the correct replacement motor for the motor you have referenced. You will also need a Pentair Whisperflo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I currently have one of these units (Centurion B 2842) in operation and am experiencing a buzzing or loud humming noise coming from the pump housing. To me it sounds like a bad bearing noise. I've ordered a new replacement pump but would like to repair the old unit for an emergency spare. Are there bearings inside the pump housing that can be replaced? If so, do you sell them? Thanks.
Reply
Is this the proper motor to replace this Century 1.5hp Y56Y? See attached picture for more details.
Hello Tim, yes based on your model number 196337 the Century 1.5 HP Square Flange 56Y Full Rate EE Motor - B2842 would be the correct motor.
Reply
Would this be the correct motor replacement? I have included pictures of motor and pump. Thank you!
Hi Mike, yes, this is the correct single speed replacement motor for the motor included in your photo. You will also need a Pentair WhisperFlo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Hi, I have a Pentair Whisperflo WFE-6 1.5 hp pump that may be in the ballpark of 10 years old. If I want to replace the motor, is this the correct one or is there another you'd recommend?
Reply
Hi Rodney, Yes, this is the correct replacement motor for the motor included in your photo. You will also need a Pentair Whisperflo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Is this the proper replacement for the century I have?
Hi, yes this is the correct replacement motor for your motor. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Is this the right placement for me?
Hello. The Century Motors 1.5HP Full Rate Motor model B842 is a compatible replacement for Pentair Motor model 177451. It is recommended that the motor shaft seal, seal plate gasket, and diffuser o-ring be replaced at the same time. The GOKIT32 contains the necessary parts to complete this project. Tune Up Kit Pentair/Purex Whisperflo - GOKIT32 The GOKIT32 SALT is recommended if you have a sat pool. Tune Up Kit Pentair/Purex Whisperflo Saltwater - GOKIT32SALT
Reply
Hello! I would like to replace 8-177451-03 motor. Could you explain how to get access to the motor shaft on the back to be able to fix it to remove the impeller? (The back cover is different from other motors - please see attached photo). Thanks!
Thank you for contacting Inyo Pools, On the back of the motor on the very end of the rigid plastic cap is a metal cap that comes off. Your going to need a very thin flat head screw driver.
Reply
I need to replace my pentair whisperflo WFE-6 motor. I assume I can replace it with a B2842. I would like to replace with either a B2843 or B2844. Would that be a problem?
Jim
Reply
Hello James. The Century Motor model B2842 closely resembles the Whisperflo WFE-6 original motor specification. The Century Motors model B2843 has a slightly higher total horsepower (THP) rating but is not as energy efficient as the B2842- still a compatible replacement. The Century Motors model B2844 has a THP of 3.45 and an even greater energy draw. Technically, the B2844 is a compatible replacement but what is the goal of such a large increase in THP? It is recommended that the shaft seal and gaskets be replaced concurrent with the new motor. The GOKIT32 contains the necessary parts. Tune Up Kit Pentair/Purex Whisperflo - GOKIT32
Reply
Will this pump replace the motor below on a jandy, what is shaft diameter
Hi Steven, the B2842 motor will be a perfect replacement for your old 0-193994-06 motor. The motor shaft diameter is 5/8" but the shaft seal is specific to the pump and not the motor. Let us know what the model of the pump is that the motor attaches to so we can help you choose a new motor shaft seal or Tune-Up Kit to ensure a leak-free installation.
Reply
Pic attached
If the motor will be installed in California, you will need a compliant motor, the B2842 is not. The V-Green 2.7 HP Square Flange 48Y Variable Speed Motor - ECM27SQU or Century 1.5 HP Square Flange 48Y Dual Speed Full Rate Motor - SQS1152R w/manual toggle for high/low 1011431-001 The serial# N07FL3273 confirms Pump Shaft Seal 3/4" - R0445500 all other o-rings are located here on the Jandy Stealth SHPF & SHPM Series Pump parts page https://www.inyopools.com/parts_jandy_stealth_2006_current_shpf_shpm.aspx
Reply
Will this pump be a good replacement for fool motor 1081 model number c55cxkls-5006. Do I need to change the pump shaft seal?
Reply
Hello. The Century Motors 1.0 HP Up Rate Motor model USQ1102 is the direct replacement for the motor model C55CXKLS-5006. USQ1102 The total horsepower of both the USQ1102 and the C55CXKLS-5006 is 1.25 HP. The total horsepower of the B2842 is 2.21 HP. Technically the motor B2842 is a replacement option but not necessary. It is recommended that the motor shaft seal, seal plate gasket, and diffuser o-ring be replaced concurrent with a new motor. These parts are specific to the manufacturer/model of the pump and not the motor. Please provide manufacture/model number information and a recommendation can be made.
Reply
My Pool Pump Motor went out and i need a replacement motor, I am needing a replacement here is the info on the motor that I need to replace. Century E-Plus Part # 7-193994-06 - Frame Y56Y - HZ 60 - Volts 208-230 - Amps 9.6-8.8 - RPM 3450
I believe i am needing a B2842 replacement motor but i am not 100% sure
Please let me know what motor i am needing to get
Thank You
Brian
Reply
Hi Brian, you are correct. The Century 1.5 HP Square Flange 56Y Full Rate EE Motor - B2842 is the perfect replacement for your old 7-193994-06 motor. Let us know what the model of the pump is that the motor attaches to so we can recommend a new motor shaft seal or tune-up kit for a leak-free installation.
Reply
Is this variable speed? If not what similar model of this company has a variable speed pump and at what price?
Reply
Hi Paul, the total horsepower of the B2842 motor is 2.21, so the variable-speed version of this motor is the V-Green 2.7 HP Motor - ECM27SQU. You can really save a lot on your electric bill when you set it up properly. Let us know what the model of the pump is that the motor attaches to so we can recommend a new motor shaft seal or tune-up kit for a leak-free installation.
Reply
Hi. I need to replace my Pentair pool pump motor. 7-177451-03.
1.5 HP. 208-230 volts. SF Y56Y.
Which of your products will work? Thanks.
Reply
Hello Rick. The Century Motors 1.5 HP Full Rate Motor Energy Efficient Motor model B2842 is a compatible replacement for the motor model 7-177451-03.
Reply
Hi - I need to replace my pool motor; photos of motor info and the pump model are attached.
Please provide recommended motor & seal kit.
Thanks.
Hello Alan. The Hayward Pool Products 1.5 Hp Max Rate Dual Speed Motor SP3210Z2MER is the correct replacement motor for the Hayward TriStar Pool Pump Model SP3210X152. Motor, 1.5 HP Maxrate Dual Speed Tristar 208/230v The Tune Up Kit Hayward TriStar/EcoStar - GOKIT81 contains the parts necessary for the successful completion of this project.
Reply
Hi, I have a Jandy MAX HP, Model # MHPM1.5 with a Century Centurion, A.O. Smith Pool and Spa Duty motor. I would like to know if you have the capacitor for this motor. This motor also states that it's a Centurion Switchless Motor, No Switch & No Governor. I have sent photos also. The capacitor is a two prong, 3 inches long and 1 3/4 inches in diameter and silver in color. Thank you!
Hello Mike. The RUN CAPACITOR, 30 MFD (5VR0303) (2444) is the replacement capacitor matching Voltage and Microfarad (uF) specifications of the capacitor in the attached photo.
Reply
Would this be the correct motor to replace my Pentair 011519, PMP WFE 28-208 230V 2HP (Century Centurion 7-177451-03)?
I'm a little concerned because the pump says 2HP in a few spots. Thank you.
Hello Jim. The Century 2.0 HP Square Flange 56Y Up Rate Motor - B2855 is the correct motor replacement for the Century Motors model 7-177451-03 installed on the Pentair Whisperflo WFE-28 model 011519. The Tune Up Kit Pentair/Purex Whisperflo - GOKIT32 contains the seals and gaskets necessary to complete the motor replacement. Attached please find the Pentair Whisperflo Pump exploded parts diagram for further reference.
Reply
I have a pool pump A.O Smith part 7-177451-03 I need to replace. It has an FR- Y56Y - 2,0 HP 1,1 SF - I attached pictures for reference - I would also need the gaskets and any other misc parts which may be needed
Hello. The Century 2.0 HP Square Flange 56Y Up Rate Motor - B2855 is a compatible replacement motor for the A. O. Smith 2.0 HP motor model 7-177451-03. The Tune Up Kit Pentair/Purex Whisperflo - GOKIT32 contains the necessary seals and gaskets to complete the new motor installation. Attached please find the Pentair Whisperflo Pump exploded parts diagram for additional reference.
Reply
I am ordering the Century 1.5 HP Square Flange 56Y Full Rate EE Motor - B2842. What is the correct Tune Up Kit for the Pentair/Purex Whisperflo pump
Reply
Hello Francisco, please click here to view both the standard and saltwater tune up/seal kits for the Pentair WhisperFlo pump series.
Reply
Need an exact replacement for this pump including necessary gaskets and seals. I am unsure if the B2842 is the right one!
Hello, based on the image provided the direct replacement pool pump motor is the B842. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that should assist you with that as well.
Reply
Hi, I need to replace the motor in the attached pictures. Is this the correct part?
Hello Sandra, the correct single speed replacement motor for your motor part number 177451 is the B842. When replacing a pool pump motor we also recommend replacing the seals and gaskets. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that we put together which should assist you with that.
Reply
