I am replacing a Jacuzzi 15UMF-S Jacuzzi Magnum Force Pump. The order number matches your part number 94027115. Your pump is a Magnum not a Magnum Force. Is the Magnum Force no longer available?
Reply
Teyy, The Magnum and Magnum Force are the same model pump. The name has changed.
Reply
How to drain the swimming pool?
Reply
Check out our guide on "How to Drain an Inground Pool".
Reply
How to install a new pump?
Reply
Our guide on "How to Replace a Pool Pump" will help explain the installation process.
Reply
Hello I need to replace the strainer pot in Jacuzzi Magnum Force pump built 1/02/03. It has a 9" basket. What part should I order?
Reply
What pump do I need to replace a jacuzzi model S15LR-S
Reply
Hi Dave, The Jacuzzi S15LR-S 1-1/2 Hp 115/230v, No Cord (94027810) will be the correct replacement.
Reply
We have a Jacuzzi Magnum pump with a Magnatek Century Centurion motor with part # 8-184948-21, HP?, Type CX, Volts: 230/115, AMP3: 3?.0/14.0
HZ:60, RPM:3450, TIME: CONT, CODE L, ENCL:DP
FR: X56J. FO?:KJM, PH: 1, SERIAL: BP1-158
1081 POOL PUMP DUTYMOUNT HORIZ WITHVENT HOLES DOWN
We are looking to replace the motor but cannot find information about a comparable one on the internet.
Can you give us any insight as to what specs we need to look for to replace this motor
Reply
Jennifer,The cross reference for motor # 8-184948-21 is part # 5221ax on our site.
Reply
How do you change it to 110 volt?
Reply
If you are wiring for 115V, the three wires to the pool pump will be black, white and green. Attach the white wire to terminal 1 of Line 1 (L1). Attach the black wire to terminal 3 of Line 2 (L2). Attach the green wire under the Ground screw (GND). The black plug is shifted in position so the the black wire is attached to terminal 4 Line 2 (L2) and the white wire is attached to terminal 5. Note: in this position the white arrow on top of the 2 prong black plug is pointing at the 115V label.
Reply
Hi, just bought a house with an in-ground pool. The pump is not working. The model is a Jacuzzi Magnum Plus 1UMP-S order no: 94026770. Do you have a replacement motor or what pump is compatible if I decide to replace the whole unit.
Thanks in advance.
Reply
Hi Michelle, if you would like to replace the motor, you'll need the A.O. Smith 1 HP Round Flange Up Rate Motor (UST1102) and the Jacuzzi Magnum Tune Up Kit (GOKIT14). If you decide to replace the entire pump then the Jacuzzi Magnum Pump 1 HP Pump will be the correct replacement.
Reply
Is the Jacuzzi magnum 1.5hp pump the same as an old jacuzzi magnum plus 1.5hp? what is the difference between the two? Your help is appreciated in the purchasing decision.
Reply
Hi Mike, The difference between the Magnum and the Magnum Plus is that the Magnum Plus uses full rate motors and the Magnum uses Up Rate motors.
Reply
I currently have a 15 year old Jacuzzi 15UMF-S Magnum and I was wondering should i go back with the Jacuzzi Magnum or is it worth the extra money to get the Hayward Super Pump? The only reason I am looking around is because my local Pool Place wants almost 600 dollars for a 1.5hp Hayward Pump and that doesn't include install. Thanks!
Reply
Hello, Mike. When replacing the Swimming Pool Pump you will need to take into consideration the output Flow Rate of the pump and the Filter's capabilities of the Maximum Flow Rate of total Gallons Per Minute. The Jacuzzi Magnum chart indicates the Jacuzzi Magnum Pump 1 1/2 HP Pump PART# 94027115 will perform at 72GPM to 50' Resistance to Flow. I would best recommend replacing the pump with the Jacuzzi Magnum Pump 1 1/2 HP Pump. Both pump manufacturers offer great quality products, as I do not know any other information regarding your filtration system it is best to replace it with the same pump. If you would prefer to send us more information in about your system, please send an email to upload@inyopools.com
Reply
I've been led to believe by many people That Jacuzzi pool supplies are now obsolete! Some sources say it was sold to another provider. How are you able to supply replacements, or were you over stocked?
Is it advisable to go from a 1hp to a 1.5hp
Thanx much
Reply
Hello, The company, Carvin, is the only authorized manufacturer of Jacuzzi products. They are currently operating, supplying parts and products globally. We have an excellent blog post, "Can I Go With A Higher Horsepower Pump?", available on our website that will answer all of your questions on upgrading you current pool pump.
Reply
Hi,
I have a few questions.
1. Does this 'pump' include the motor, pump housing, impeller, basket, etc.?
2. My bad pump has a sticker that says '2004 Magnum Force 15UTMF-S' (not -S2), motor is two speed, 1.5 HP, Order# 94027215
Is this a standard setup? ( I see you have the 94027115 with this setup)
3. Local chain sold my wife just a motor, STS1152R, it looks compatible, but at $400, I'm wondering if you have the entire setup for a similar price and I can take the motor back.
Thanks
Reply
I'm replacing a Jacuzzi 2UMF-S Magnum Force pump with a 1 1/2 HP motor (looks like a replacement motor ((UST 1152)). Would your 1 1/2 Magnum Force pump be the ticket? Thank you.
Reply
Hi Jim, the 2UMF-S is the 2 HP Magnum Force Pump if you want to step down to 1-1/2 HP then this pump here is the correct pump.
Reply
Sorry, that Magnum Force order number is 94027120. Thanks again. Jim
Reply
Jim, Yes the Jacuzzi 94027120 is the 2 HP Magnum Pump if you want the 1-1/2 HP version then the pump here i the pump you are looking for.
Reply
Hi! I currently have a jacuzzi magnum force 1 1/ hp 3phase for the jets on my hot tub. If i would like to convert it to single phase, what would be the best option so I can still have the same force I am getting from my jets?
Reply
Hi Joe, This Jacuzzi Magnum Force Pump is the single phase option for the 1-1/2 Hp 3 Phase Jacuzzi Magnum Force pump with the same performance.
Reply
I have 13 y/o jacuzzi magnum force 94026115. Would a current Carvin jacuzzi be an exact replacement including the quick connect connectors? What is the model number to order from you?. I live in Carlsbad CA? Will your diy video help me in install. It seems like it would be easy as I do a lot around the house. I have experience with in ground sprinkler install and repair and this seems like it would be similar.
Reply
Bob, There is two other body style that are a little different. You should still be able to use it but confirm here.Jacuzzi Magnum Parts
Reply
I have a magnum force jacuzzi 15umfs unit installed in 2001 when then the pool was built. I was told that a different type of pool pump like a 2phase Pentair is lower cost electricity and higher efficiency what do you think about updating it?Pentair IntelliFlo 3 HP Variable Speed Swimming Pool Pump 4x160 VS-3050 011018 is what I was considering. but I think that is a 3hp unit vs the old 1.5
Reply
Hi, Neil. If you do not want to get a 3 HP pump because it's more pump that you need, then you have several different options. The Raypak Variable Speed Pool Pump - PS165VSP is the best replacement we have available. You can view other variable speed pumps via this link > Variable Speed Pumps.
Reply
I have a 20,000 gal. in ground - my Jacuzzi Magnum Force pump lasted 15 years. Pool is run on salt chlorine generator. Numbers on pump are 1UMF-5 &94027110. Not sure of horsepower. Want to buy new pump from you. Will my current piping connections work with the new pumps? What horsepower do you recommend & which pump? I have a 200 pound sand filter - pool is not heated. Am running 230 volts Thanks
Reply
Hi, Stuart. You currently have a 1 HP Magnum Force Pump. Since that pump has worked for 15 years a would recommend replacing it with the same Magnum Force Pump 1 HP Pump - 94027110.
Reply
The pump motor has died on my Magnum Force Pump 1 1/2 HP Pump - 94027115 unit. Please recommend a replacement motor. Thanks.
Reply
Hi, Randy. You can use the UST1152 standard motor or UCT1152 high efficiency motor as a replacement for your Magnum Force Pump. I would also recommend getting the Magnum Tune Up Kit - GOKIT14.
Reply
Is the housing for magnum the same for all horsepower motors. I would like to downgrade from 1.5 to 3/4 horse power. Thanks
Reply
Hi, Frank. The housing is the same on all the different hp. To downsize the pump from 1.5 to 3/4 you'll need to replace the motor, impeller, diffuser, eye seal, and the pump seal and o-rings. Replacing the complete pump model # 94027107 may be cheaper.
Reply
My pool pump & motor ran for nearly six hours with multiport valve on closed. I found the motor still running with no water in pump skimmer basket. I opened the lid and water rushed in from pool side. I Set multiflow to filter & turned back on. water began blowing out the band clamp between pump and motor with no pressure register to the filter tank gauge. I lost 3inches of water from pool. Is my pump shot or can it be repaired? What Parts do I get to systematically check out the pump function
Reply
John. I would consider the pump shot because it will be expensive to repair. You may have to replace the drive end which is the parts from the diffuser to the seal housing depending on what went bad.
Reply
What gauge wiring would you recommend for the 1.5 HP pump, with the 16/8 Amps ? Would this wiring work for 1.5 HP with a 18.6/9.3 Amps.?
Reply
Hi Bob for 230V wiring we suggest 14 gauge wire up to 50', 12 gauge wire up to 100', 10 gauge wire up to 150' and 8 gauge wire up to 200'.
Reply
i need to replace a pool motor plus pump.
The motor is a Century Centurion and the pump is a Jacuzzi - Magnum Force.
The manufactures label for the motor shows 2.0 HP, but there is also a label that shows Total HP = 2.4.
Question - what actual HP do i need? Thanks
Reply
Yes if you have a 2hp motor with a higher Service Factor then you would go with this unit. You can also go with Magnum Force V Series 2.7HP Variable Speed Pump (VMF-S2) - 94026140
Reply
part# 7-184949-22
hp 1.0 (1.65sf)
what is replacement pump?
Reply
where can I find the motor support? Motor Support (12112405r000) Is this the correct one?
Reply
Hi, Mason. The Motor Support - 12112405R000 is the correct for the Magnum Force Pump. We do have them available.
Reply
Hey, I picked up a used Jacuzzi - 15UMF-5 / 94027115 date 23JUN00. I do not know if the motor is wired for 240 or 120 vac. How can I tell which one it is?
Reply
Hi, Rick. You can use the motor wiring diagram located on the motor to determine how to wire the motor based on your breaker. It can be wired for either 115 or 230 volts.
Reply
I have Jacuzzi Magnum Force pump 1UMF-Spump with 7-184948-22 1HP motor. I am planning on adding solar collectors on my 2 story roof for heating the pool water, and they are recommending a 1.5 HP pump. Your recommendations for pump/motor replacement?
Reply
Hi, Greg. You will definitely need a larger pump. However, the size of the pump will be based on the number of panels, plumbing size, etc. You can use this Magnum Force Pump 1 1/2 HP Pump if they confirmed it will be sufficient.
Reply
What pumps do yoU sell for my 300000 gal I ground that will run on 110 volt
Reply
Hi, Edward. We do have a few pumps that you can uses, however, we will first need to know the Total Dynamic Head (TDH) and the turnover rate. To calculate the TDH of your pool, use the info provided in these Inyo guides How To Measure Total Dynamic Head With Gauges and How Do I Calculate Feet of Head for My Pool?
Reply
I have a jacuzzi magnum force 1.5 HP pump for inground pool. What pumps are a direct replacement for same hookup with inlet and outlets?
Reply
Hi Mark. The Carvin Magnum Force Pump will be a direct replacement. You will need to confirm the service factor of your pump to make sure you get the correct 1.5 hp model pump.
Reply
Is this a dual or var. pump? When I hit details it gives me Pure line info. Is this pump still available? Is it Calif. compliant?
Reply
Hi, Bill. This is a single speed pool pump, we do not have a dual speed version of this pump. However, their is a variable speed version that can be special ordered, the Magnum Force V Series 1.65HP Variable Speed Pump (15VMF-S) - 94026117. The PureLine Prime 2.7 HP Variable Speed Pool Pump - PL2606 is also a suitable option.
Reply
I have a 20 year old jacuzzi 1mf-s pump. I also have a 75 gpm hayward sand filter. The pump I have has a 1 hp motor that is shot.
My question is, would this 1 1/2 hp pump be to strong or could I just drop this one in?
Reply
If that pump was the original pump that was installed when that filter was also installed then I would recommend keeping it the same. If you want to calculate to see if you can go up in horsepower then you would need to calculate the feet of head of the pool. Please click here to be directed to a guide that may assist you with that.
Reply
how much pressure should I see, after my filter with, with a Jacuzzi Magnum pump with 11/2 hp motor? sand filter
Reply
Hi. The pressure filter will vary based on several factors including TDH, flow rate, filter size, plumbing size etc.
Reply
What exactly is the purpose of the Strainer Basket Air Bleed Tube? Should it remain in the strainer basket submerged at all times and does it help reduce air in the pump somehow?
I have been running without it but always noticed a pocket of air at the top of the strainer basket and wonder if this would help?
Reply
The air bleed tube does not remain completely submerged, the top of the tube will actually sit right at the underside of the trap lid where you describe having air bubbles. It is not a critical part of the pump operation. If you are getting air trapped in your strainer housing look for any leaks ion the front of the pump or at the lid when you shut the pump off. You may have a small suction side leak that is pulling air into the trap.
Reply
hi i need to replace the capacitor for my Caravin magnum force 1.5 hp pool pump . Would you know the model or size . thank you
Reply
Hello, I can find the right one for you. Can you please send a picture of the motor label?
Reply
I have a carvin pool pump item no. 94027115. It’s about 25 ft. From my pool. I need to match a pool filter. The ingrown day pool is only about 18000 gallons. Can you give me some ideas? I currently have a jacuzzi de filter ew-100. Please advise.
Reply
Hi Rich, The Jacuzzi EW-100 is no longer available and if you are looking to stay with a DE Filter then I would suggest this Hayward DE4820 DE Filter and this Hayward DE4820 2" Multiport Valve. If you want to switch to cartridge then I would suggest this Waterway 150 Sq. Ft. Filter no valve is required with this cartridge filter.
Reply
I have a jacuzzi magnum force pump model 15UMF-S i need a replacement motor for it is that still possible?
Reply
Hi Yes this is possible and the correct replacement motor for your pump is this Jacuzzi Magnum 1.5 HP Replacement Motor. You will also need a Jacuzzi Magnum Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I need to replace my Jacuzzi magnum force pool pump, Jacuzzi now made by Carvin? The number on my pump is 94027115 and I see this one is 94026115 is it the same pump?
Reply
Hi Ginger, Yes this is the correct replacement pump for your pump.
Reply
What is the "Flow Rate" for the 1.5 hpp Magnum Force Pool Pump
Reply
Hello David. Attached is the Magnum Force Pump 1 1/2 HP Pump - 94027115 product page. Included on this page is performance data (Flow Rate in Gallons per Minute) at various feet of head.
Reply
