Will this be a suitable replacement for my Sta-Right original 1HP MOTOR or should I have my motor rebuilt?
Reply
Hi Allen, If you can provide the model of the Sta-Rite pump you have I can firm if this will be a suitable replacement. You can have your motor rebuilt or replace if you'd like.
Reply
Will this model replace my Hayward1:00HP; 1.25 SF; 1.25 THP Model # SPX3210X15Z1PE?
Reply
Hi Jodi for a Hayward SPX3210X15Z1PE I would suggest the 1 HP PureLine Prime Pump.
Reply
Which pump will replace Hayward C48K2N14381
Reply
Hi Ed, I would not suggest this pump as a replacement to the Hayward C48K2N14381 I would suggest the PureLine Prime 1 HP Pump as a replacement for the Hayward Super Pump.
Reply
Would this replace a Waterways Champs 110 1hp pump?
Reply
I would suggest the PureLine PureWater 1.5 HP Pump as a suitable replacement for the Waterways Champs 110 1hp pump
Reply
I currently had a 1 HP Hayward Pump (can not read the entire old label) and my question is if I can purchase a 1.5 HP pump to replace it and if so what would be the advantage of buying a 1.5 HP over a 1HP. My pol is rather small (15K gallons)and 7 roof solar panels. Also in the features you list that both the 1HP and 1.5 HP can support solar heaters but in your question and answer page you answer someone that it would NOT be suitable for solar heating system. Would you please clarify. Thank You
Reply
Hi Mike, For solar panels on a roof we suggest a high head pump and this pump is a high flow pump so I would suggest something like the PureLine Pure Water 1.5 HP Pump which would do a better pumping water up to the roof.
Reply
your add for this pump says free shipping but when i go to order it says i have to pay tax and shipping.
Reply
Shipping on this item is free. There is a $5.99 handling fee has no relation to the shipping charges. If you reside in the state of Florida, where we operate out of, we are required to charge sales tax. Shipping charges we are not including for a pump with this weight can range anywhere between $25-$50.
Reply
Will this 1 hp pureline pump replace my Hayward 1 hp Super Pump 115/230 v, 15/7.5 amps?
Reply
When replacing your 1 HP Hayward Super Pump, I would recommend the PureLine Prime Pool Pump 1 HP - PL2601.
Reply
purchased the pl1600 pump, the threaded fitting on top of pump has a slight leake, would this have anything to do with low pressure? also are the threads different from standard 11/2 in. threaded fitting. seemed a little loose when tightend did wrap well with tape. thanks FRANK
Reply
Yes any amount of leak is going to affect your pressure.
Reply
looking to replace a Aqua Tools AT2410111 S/N 1M03H 1 hp/ 11 5v/ 3450 RPM.
Looking to replace motor/pump/hair debris basket assembly as 1.
Thank you
Reply
Hi Todd. The Aqua Tools model provided is for an above ground pool pump. You can use the Sta-Rite Dynamo Pump (340197SR) as a replacement.
Reply
I have a Flotec - AT251001-01, 1hp, 13.4/6.7 amp, motor that was flooded with salt water.
Do you have a replacement motor and seal?
Thanks Jim
Reply
The correct replacement motor is part number USQ1102 and the shaft seal for saltwater pools is 35-423-1096.
Reply
I have in ground 25,000 gal pool with a Sta-rite P2R 450-1201 with a one HP motor. Should I stay with the 1HP or move up to the 1.5hp? How does this $200 pump/motor compare quality wise to the present Sta-rite I've listed above.
Reply
Is this a suitable pump if I am looking for one that is a Eco power consumption pump?
Reply
Hello Nick- The 1 H.P. In Ground Pool Pump PL1600 is a standard single speed pump, if you are looking for an Eco-Friendly pump I would suggest the PureLine Prime Variable Speed Pool Pump 1.65 HP - PL2605.
Reply
#PL1600 will this product fit my system MAX-E-PRO 11/2 HP P6RA6F-206L .
This is round flange in ground pool, I only need the motor. any help cost wise will be greatly appreciated. thank you
Reply
Hello Michael- No the motor from the PL1600 1 H.P. In Ground Pool Pump - 72743 is a round flange, you Sta-Rite Max-E-Pro 1 1/2 HP Up Rate Std - P6RA6F206L requires a square flange motor. The motor you would need is an A.O. Smith 1 1/2 H.P Square Flange Up Rate Motor - USQ1152.
Reply
Hello, I need to replace a Sta-Rite 3/4 HP PHK2RA6D-101L motor that I currently have on my spa. would this pump be a suitable replacement?
Reply
Hi JJ. This pump would not be a suitable replacement for the PHK2RA6D-101L pump, I would recommend the PureLine Prime Pool Pump 1 HP - PL2601.
Reply
I have a Dura-glass pump with a 3/4 horse motor. model pr2A5D 120L. It sits on a plastic base approximately 4.5 inches off the ground. The input and output ports use a 1 1/2 inch threaded coupler from the pump to 2 inch PVC pipe. All the other measurements seem to line up with your drawing except for the height. I replaced the motor 7 years ago and the pump is going on 20 years old. My pool is a 7000 gal in ground fiberglass shell. How can I make this model work as a replacement
Reply
You can make that one work, but I would recommend the Prime, part number PL2601, over the PL1600. I have had a lot better luck with the Prime as far as performance and durable is concerned.
Reply
will this model 1 H.P. In Ground Pool Pump - 72743 work as a suitable replacement for SuperFlo 1 HP Single Speed Pump - 340038
Reply
The PL1600 will reduce your flow rate by about 20 GPM. If you are okay with that then the PL1600 is fine for a replacement pump.
Reply
will this pump work to replace my Pentair 340038 SuperFlo Standard Efficiency 1HP Single Speed Pool Pump, 115V/230V
thank you for your help
Reply
If you are fine with a 20 GPM reduction to your flow rate then the PL1600 can replace your SuperFlo.
Reply
Emerson pump in my pool is not working. Model number T55CXCHL-1324. The white/black wire is not connected and I can't find schematics to see where goes
Reply
Hi, Paul. The motor should have a field wiring diagram directly on the label that you can follow. In order to assist you, I will need to know if the motor is being wired for 115 or 230 volts.
Reply
Hi, I have a 16,000 gal fiberglass pool with a 2 HP AquaPro pump. "Not sure why the installer gave me such a large pump", It is expensive to run. Anyhow, I want to drop to a 1HP pump and save money. Calculations say this pump should cycle pool in less than 6 hours. Do you suggest this pump as a good replacement "fit a form included"? Thank you.
Reply
That answer will depend on the flow rate. What is the distance from your pump to your skimmers?
Reply
I have a Hayward super pump self priming pump. Would this pump be good for me. 22,000 gal in ground pool.
Reply
Hi, Dwight. You will first need to calculate your pool's Feet of Head in order to find out if this pump will fit your pools needs.
Reply
Are replacement parts available from you for this pump? Do you have wiring instructions available?
Reply
Yes here is the parts diagram for the PL1600, the 110 volt wiring instructions, and the 230 volt wiring instructions.
Reply
I currently have a Hayward Motor model C48L2N134C2/ Serial 13513CH, 115/230 volts, 1HP unit. The motor seems to still be fine but the housing is cracked where the filter is. Would this unit be sufficient as a replacement. I have an approximate 25,000 inground pool with a sand filter (if that makes any difference)...
Reply
Hi Tabbi, You have a 1 HP full rate motor which is a bit stronger than this pump. I would suggest the PL2602 1.5 HP PureLine Prime as a suitable replacement for your C48L2N134C2
Reply
I need to replace a Hayward Super Pump, model (A. O. Smith) C48J2N131B1, SP-1605-Z1-M
Specs: 3/4 HP, 115/230 volts, max/load 11.0/5.5 volts volts, ,55 kw, 3450 rpm.
Since this pump is 1 hp, would work ok with My filter, which is a Hayward S210T that states max 40 psi 2.7 bar.
There are 3 elbows & about 3 ft of pvc between pump & filter.
Thank you!!!!!
Reply
If the 3/4 horse power was installed there per the builder then I would leave it as such because that may be what is best for the filter due to the flow rate. Now if you really want to step up to the 1 hp then you will need to calculate the feet of head to make sure that the filter can handle the extra flow rate.
Reply
I want to add a booster pump to my system, this pump be ok?
Reply
Hi, Piper2. It depends on what the pump will be used for, this pump will be too big to operate a cleaner which is the main reasons for a booster pump.
Reply
Replacement pump for model _k48L2n104
1 hp
Volts 115/230
Amps 14.6/7.3
Reply
Hi, In order to locate a suitable replacement pump we will need to know the model of the pump that the K48L2N104 motor operates.
Reply
I recently purchased the pl 1600 and I would like to know which fittings to get to connect to the 1 1/2" ports. Pipe size is 1 1/2"
Reply
I would suggest two of these 1.5" x 1.5" Unions
Reply
Can I use this to replace Pool pump with Century Centrum 1 Hp engine B2841V1 ? What accessories do I need to buy?
Reply
If you have a B2841V1 motor then I would suggest the PL2602 PureLine Prime 1.5 HP Replacement Pump as a suitable replacement.
Reply
have a Water Ace RSP 10 pump with a 1hp motor. will this pump be a good replacement for it?
Reply
Hi Stephan, Instead of this pump I would suggest the 1 HP PureLine Prime PL2601 Pump it will be closer in power to your Water Ace RSP 10 pump
Reply
Will this pump replace a p2ra5 120l sta- rit
Reply
Hi Barry, I would suggest the PureLine Prime PL2601 1 HP as a more comparable replacement to your p2ra5 120l sta- rite pump as the output of water produced by the PureLine Prime will be more comparable to your Sta-Rite pump.
Reply
what is the discharge lift for this pump?
Reply
Hi. Unfortunately, the discharge lift is not available. You will have to calculate it. The Formula is PSI (filter pressure, clean) x 2.31 ft of water / PSI.
Reply
I have a Hayward Super II self-priming pump with a 1 horsepower motor. My pool is an inground fiberglass pool and I'm not sure of the gallons. Is this pump suitable to replace what I have? My motor is seized
Reply
Would this replace my Sta Rite P2RA5E-181L, which is connected to my 10,000 gal. in-ground lined pool?
Reply
Good day, the PL1600 would not match your gallons per minute specs on that unit. We would reommend PureLine Prime Pool Pump 1 HP - PL2601
Reply
I have a 1.5 hp Hayward super II for 13000 gal inground pool.. This pump was put in by previous owner. The pressure 22lb in my progrid filter 48 ft de. I destroy grids regularly. I think i need to down grade to a 1.0 hp pump. Would I need a PL1600 or a PL9601 to do this? Thank you for your assistance.
Reply
Hi, Glenn. It's possible, however, I cannot confirm without knowing the TDH or Feet of Head of your pool. If you can provide us with the info outlined in our How To Size a Pool Pump Guide, we'll be able to assist you.
Reply
is this an inground pool pump and can i replace my 3/4 hp hayward pump with this?
Reply
Hi David, Yes this is an inground pool pump and it would be a suitable replacement for a Hayward 3/4 HP pump.
Reply
Hello i have an emerson 1.5hp pump for a 8500 gallon pool. Would this be suitable or comparable?
Reply
Hi, Brian. Unfortunately, you will need to provide us with the pump housing model in order for us to confirm. We're unable to tell by the motor only.
Reply
I have a 4 ft deep in-ground. Is a 1hp sufficient. I have a1.5 currently that I purchased from Inyo a few years ago. It was a good pump and having a problem holding prime.
Reply
Hi Jim, Based on your previous purchase I would suggest something like the PureLine Prime 1 HP Pump. If you are looking to go down in HP then you would need a stronger pump the like the PureLine Prime.
Reply
I currently have a P2RA50-180 with a 3/4 HP 3450rpm motor and i need a replacement for that, what do you recommend?
Reply
Hi Jim, we would suggest this PL1600 PureLine Pump as a great replacement for the Sta Rite P2RA5D-180. The plumbing ports are not in the exact same position so you may have some minor re-plumbing, but nothing major.
Reply
First of all, thanks for the quick response to my last question. I have one more, you guys recommended the PL1600 pump for my pool, but I noticed it only has a 1 year warranty. Is this a good pump that will last for years? I definetly don't want to be changing pumps out every couple years. Thanks.
Reply
Hi Jim, Yes the PL1600 is a good pump that will last for years, we think you will be quite happy with it.
Reply
can this pump be wired to 110 v
Reply
Hi, Dale. Yes, this pump can be wired for 115 volts. You reference our PL1600 & PL1601 Wiring Instructions 115V & 230V.
Reply
Would this be a good replacement for WhisperFlo WFE-24 1HP S/N 1-19-L02. The pump is dedicated only for the 2 x waterfalls . Thanks
Reply
We are looking to replace a Duraglass C48H2PA105. Would you be able to tell me if this pump will work as a replacement?
Reply
Unfortunately, no this pump would be more than a quarter of a horsepower weaker than what you currently have. We do not have a single speed Pureline pump that would match the model that you have unless you went to a variable speed that you could set to many rpm's. Maybe look into our PL2605 pump.
Reply
i have a 26000 gal inground pool, and a hayword sp2607x10 pump will this work for a replacement. with the math it came out to 3250gph, 54gpm
Reply
I have a sta-rite model number p2ra5c119l. Will this pump work as a replacement?
Reply
I have a Sta-Rite PR2 pump with a 3/4 hp motor and a Str-Rite 70 cartridge, will this pump be a good replacement? My inground pool has 13,000 gallons and stays clean with 6 hours of filter run time. Will this pump be a good replacement? I have had the original pump for 40 years and have only replaced motors to date.
Reply
Hi, John. This pump does not match the performance of the 3/4 HP P2R pump. To determine if this pump will be sufficient, I will need to know the Total Dynamic Head (TDH) of your pool. You can use our How Do I Calculate Feet of Head for My Pool? or How To Measure Total Dynamic Head With Gauges guides.
Reply
I want to replace the pool system we have now, the motor we have is ST1102. can I replaced with the PL 1600?
Reply
we have pool pump PL2102, will this work as replacement? (115/230v 1.0hp FR48Y)
Reply
Hi, Jessica. The info provided is for the motor, I will need to know the pump housing model or name and the Total Dynamic Head (TDH) of your pool.
Reply
I have a HSQ 125 will this work as a replacement
I would not recommend this pump as a replacement because it actually has about a quarter of a horsepower less than your current model. I would look at something like the model P6RA6E205L.
Reply
on my pump it says a.o. smith corp. In my paper work it says it's a max-e-glass. model number K48L2PA101A1, 1hp, 115/230,48y,SF 1.65, AMPS 16.0/8.0,RPM 3450. would this work for a replacement
Reply
I have an inground pool 14 x 28 6 foot in the deep end the pump motor assembly it has on there now is rusted so I don’t know what size it is can you tell me what size motor pump assembly I would need
Reply
Hi, Jim. I'm unable to confirm what size pump you'll need for your pool. I'll recommend that you use our How to Size a Pool Pump for Your In-Ground Pool.
Reply
I have moved to a new home, with an In ground pool approximately 12,000 gallon.
Is the P1600 1 hp enough for my pool.
What size sand filter do I need. I want the side connecting filter
Reply
Hi, Joe. In order to assist you, please review the following guides; How Do I Calculate Feet of Head for My Pool?, How to Size a Pool Pump for Your In-Ground Pool, and How To Size a Pool Filter.
Reply
I need to replace P2R A5E 124L pool pump code # 1091U 1HP 230v Marathon, the inlet is 11 1/2 inches off the ground, what replacement pump will fit, thanks in advance for your help
Reply
Good Afternoon,I can surely help match you with a replacement pump. Do you live in California?
Reply
I am replacing an old Hayward SP 2800X Max Flo from 1991 the current motor is a Weg. The height for the suction on the pump is about 9.5" from the bottom of the frame and the discharge height is about 11'. Is there a 1 hp Pureline with the Century motor that will be close to a drop in fit? If not, any recommendations? Looking for single speed. Thanks.
Reply
Hi, Mark. This Pureflow pump and the Prime pumps are close drop-in replacements but not exact. However, will not perform as good as the MaxFlo pump. We do still have the Hayward Max-Flo Pump 1 HP Single Speed Pump - SP2807X10 which will be a direct replacement.
Reply
Sir, I have sta-rite 1hp pool pump model phk2ra6e-102l , will this pool pump work to replace my pool pump Thanks Jim
Reply
So this pump actually has about a quarter of a horsepower less than your current model assuming the motor on there is or matches the original specs that came with the entire pump. I would advise looking for any in-ground pool pump that matches the total horsepower of 1.25.
Reply
I have a very old US motors pump, would this pump be a good upgrade choice? Thanks
Hi Al, Yes the motor used on the PL1600 would be comparable in power to the U.S motors motor you have shown in your photo. You might even consider upgrading to the PL1601 1.5 HP Pump as it is only $10 more and would give you more output/gallons per minute.
Reply
Hi, I am trying to replace the my Hayward pool pump
hayward max flo xl pump C48D31A04
Will this one work?
Hi, Tony. This PureFlow pump will not be a good replacement for the MaxFlo XL pump comparing the performance curves. However, if you can get the Total Dynamic Head (TDH) of your pool we can confirm if this pump will meet your pool needs.
Reply
Will this pump be a good replacement?
Hi Casey based on your motor specifications we would suggest a pump like the PureLine Prime 1.5 HP the PL1600 will pump considerably less water than your current pump.
Reply
I have an old AO smith USQ1072 which is 115/230 volts and 3/4 hp. Can I replace that with this pump
Reply
If you are looking to replace your entire pump then yes the PL1600 will be equivalent in power to your USQ1072 motor, however, please note you will have a bit of re-plumbing when installing the PL1600 as the plumbing ports will not be in the same location as your pump which uses the USQ1072 motor.
Reply
Would this be able to replace my hayward c48k2n143b1? Thank you in advance
Reply
Hello, We would need to compare the GPMs on your current pump. What would be the brand and the model of the entire pump?
Reply
dyna-tech is the pump on my pool now--its 1hp --volts 115/230 --- will the pure line 1600 work as a replacement --thanks
Reply
Hi Steve, The PL1601 1.5 HP Pump would be more comparable in output to the Dyna-Tech 1 HP and the PL1601 would be a suitable replacement. You may have a little bit of re-plumbing but it should not be too bad.
Reply
Trying to replace AO Smith c48k2n143 Serial 8b95, frame 56j
Reply
Hello,This will be the replacement motor you will need.http://www.inyopools.com/Products/00200017001331.htm
Reply
I need to replace my sta-rite 1 HP maxi II ( 12 years old)...this is for the PCC 2000 jets that clean the bottom of my 18,000 gallon inground pool. The pump/motor is the same HP for the filter/cartridge > 1 HP too. My two questions are:
1) Will this do the job & be a great replacement?
2) Should I keep the HP the same @ 1 HP? Since this is the size they engineered for my pool....or should I install the 1.5 HP....is that too much?
Reply
Hi Greg, The PureLine Pure Flow series pumps a little less water than the comparable HP in the Sta-Rite Maxi II. Our suggestion would be to go with the PureLine Prime 1 HP as that will be more comparable to the output of your Sta-Rite Pump. Since this is powering the floor jets you want to make sure you have enough power to pop those up, so you may even consider the PureLine Prime 1.5 HP PL2602
Reply
My pump still runs but isnt pushing water. I talked to a couple folks that think it could be a clogged impeller, does that sound right?
Everyone here is replacing the entire pump, just trying to save time... check impeller? Or replace entire pump?
Reply
Hi Robert, I would check the impeller first by following our Video on How to Unclog an Impeller. If that doesn't work then I would replace the entire pump.
Reply
trying to find out the gallons per minute before i add a salt system to my pool
thank you
Reply
Hi. To determine the flow rate of this pump, you will need to calculate the Total Dynamic Head (TDH) of your pool. Once that is calculated, use the PureFlow Performance Curve to see the GPM.
Reply
Would this pump be a good replacement for a Centurion 1 hp 1081?
Reply
H MPrice, Could you send us a few photos of your pump? One being a wide shot of the pump showing where the plumbing goes in and out of the pump and a second showing the motor label that shows the amps, volts, hp, etc.. To upload your photos simply click on the reply link below. Once we get these photos we can confirm if this pump will work for you.
Reply
I currently have a hst110 pool pump. No longer functioning. What would be the best replacement for it? Thanks
Reply
Hi, Johnny. HST110 is the motor model which is different from the pump. You will need to provide us with the model number or name in order to locate a suitable replacement.
Reply
Looking to replace a Hayward super ll pool pump what do you suggest
Hi Todd, We would suggest the PL2601 PureLine Prime 1 HP Pump as it will have a similar gallons per minute output as your Hayward Super II 1 HP.
Reply
How about the plumbing?
Reply
Todd, The plumbing will have to be redone to match the Prime pump.
Reply
Still no answer on what pump to order
Reply
Todd, The PL2601 - PureLine Prime 1 HP Pump was suggested as a Pureline brand replacement.
Reply
I have a 1mfs 94026100 jacuzzi pump .what would replace this
Reply
Hi Mike, this pump would be underpowered compared to your Jacuzzi 1MFS Magnum Pump. Our suggestion would be the PL2602 PureLine Prime 1.5 HP Pool Pump the plumbing ports on the PureLine Prime will not be in the exact same position as your Jacuzzi Magnum so you will have a little re-plumbing but it should be nothing major.
Reply
can you show me a picture on how to wire a pl1600 for 110 volts please
Reply
Hi Howard, Here is both a written guide and Video on How to Wire the PL1600 on 115V this should help out quite a bit.
Reply
thank you i found the answer on google which led me here.not trying to be a pain but the search feature here is not very helpful i do appreciate your help thank you again
Reply
Thanks Howard I hope you get the pump up and running, if you have any issues feel free to reach out to us and we would be happy to help.
Reply
thank you and yes i got it running fine now i had the white and black wires crossed causing the motor to over heat and shut off and after a few minutes it would start back up
Reply
Howard Thanks for the update I'm glad you were able to get it up and running.
Reply
Looking for a replacement for my Hayward 1hp super pump model c48k2n143b1. And if the plumbing will be the same.
Thanks
Reply
We have the Pureline Prime model PL2601 which is a near identical design to that Hayward Super Pump. It has 2 inch ports which can always be reduced to 1.5 inch with reducer fittings and also uses a Century A.O. Smith motor. It also come with unions and if you have a saltwater swimming pool then you can use the model PL2621 model which has a heavy duty shaft seal.
Reply
I just ordered the PL-1600 pool pump. Please confirm a standard 1 1/2 PVC pipe thread will screw into the pump's inlet and outlet connections. Thank you.
Reply
Yes these ports are standard 1.5 inch female internal threads.
Reply
Hi I have an A.O. Smith C48K2PA105, 1HP motor and it needs replaced. I'd like to replace the full pump to use with my 30in diameter sand filter for a 35,000 gal in ground pool. Will this unit work to turn the water with an in pool my size? If so does this come fully assembled with all the seals and simply needs plummed and wired?
thanks,
-Jonathan
Reply
Hi, Jonathan. Unfortunately, with the info provided, I'm unable to confirm if this pump will be able to meet your pools needs. You will need to provide us with the model or name of the pump housing or the Total Dynamic Head (TDH) of your pool.
Reply
Thank you for the reply, it says Sta-Rite Duraglas on the motor casing. The same build as shown here: http://www.inyopools.com/pool_parts_sta_rite_dura_glas_and_max_e_glas.aspx.
Reply
Hi Jonathan, Based on the information you supplied we would suggest the 1 HP PureLine Prime Pump as a suitable replacement for your Sta Rite Duraglas C48K2PA105. This pump does does come fully assembled with all the seals and simply needs plumbed and wired.
Reply
Need a replacement with minimal work
Hi Jeff, This PureLine PL1600 Pure Flow would be a great option as a replacement for your Hayward Max Flo. The plumbing ports on the PureLine Pure Flow are not in the exact same spot as your Hayward Max Flo so you will have a little re-plumbing but it should be nothing major.
Reply
Will this pump replace my 1hp Aqua Flow brass pump for a 10,000 gallon pool with 24” sand media filter?
Reply
Hi Chris, We would actually suggest the PL1601 1.5 HP PureLine Pure Flow as a suitable replacement for your Aqua Flow brass pump. You will require a little bit of re-plumbing as the plumbing ports on this pump are not in the exact same spot as your Aqua Flo pump.
Reply
HI. I'm replacing a Century Centurion B129 pump that (I think) runs my dedicated vacuum suction line. Will this pump be a good replacement?
Reply
Hi Rich, The PureLine Prime PL2603 2 HP uses a motor which is more comparable in power to your B129 motor. Our suggestion would be the PureLine Prime PL2603
Reply
Will this replace a pentair challenger 1.5 hp pump and motor with 2 inch ports
Reply
This pump would have less flow than a 1.5 HP Pentair Challenger. I would suggest the 1.5 HP PureLine Prime as great replacement pump, the plumbing ports on the PureLine Prime are not in the exact same spot as your current pump so you will have a little re-plumbing
Reply
Looking for a compatible model Jandy FHPM1.0 Jandy FHPM 1.0 FloPro 1HP Single Speed Swimming Pool Pump
Reply
Will this replace a star rite MPRA6E-205L (1HP SELF PRIMING) or do you recommend something else thanks in advance
Reply
Hello - the PL1600 would not be a suitable replacement for your 1-HP Sta-Rite Dyna-Glas. I suggest using the Pureline Prime 1 HP - PL2601, as it will provide the closest flowrate output to your Dyna-Glas.
Reply
We are buying a rockwood semi /in ground 24 foot round pool kit. It holds about 12500 gallons. Q1. Should we get this one (will it work ok with this pool?) . Q2. Would this be more energy efficient, or do you recommend a 1.5 and if so, which model? Q3. What filter to you recommend to go with this pump? (or if you suggest the 1.5 pump-what filter should we get)?. Q4. Thanks!
Reply
Hi, Rachel. We're unable to provide you with the answers to your question without knowing the Total Dynamic Head (TDH) of the pool.
Reply
Is this a good replacement for my 32 year old Sta-Rite Max e Glas 1 HP jacuzzi air pump?
Hi, Larry. This Pump can be used as a replacement based on the Total Dynamic Head (TDH) and the required flow rate that is needed to meet your pools need. You can use our How to Size a Pool Pump and How To Understand High Head vs Med Head Pumps guides for more info.
Reply
what rpm's is this pump
Reply
Matthew, the PL1600 PureLine 1 H.P. In Ground Pool Pump motor runs at 3450 RPM.
Reply
Does this pump also come with the wire need to power/connect the motor? Or does that need to be purchased separately?
Reply
Hi, John. This unit will have to be hardwired, the electrical whip will have to be purchased separately.
Reply
I am replacing a pentiar 1 hp superflow 340038 pump would this do the job..? rectangular inground 16x32 3ft shallow 8 ft deep roughly 25000 gallon with a jaccuzzi sand filter with60gpm capacity
Reply
Hello, Yes, this pump would be a good alternative option.
Reply
Hello, my in ground pool pump is old and I want to replace the whole thing. Attached are 2 pics. Can I use the PL 1600 ? You can also call me. 239 600 1616
Thank you
Bernd
Hi, Bernd. This PL1600 model pump does not have the same performance. In order to confirm if this model pump can be used, we will need to know the Total Dynamic Head (TDH) of your pool.
Reply
What is the warranty for this pimp
Reply
John, the PureLine 1 H.P. In Ground Pool Pump comes with a 1-year warranty from the date of purchase.
Reply
will this pump replace an old Hayward, model SP-1607-Z1-M
Need a seal kit for the motor, is it sold separately? Thanks
Reply
Seal kits are sold separately from motors however, this is a complete pump so you would not need a seal kit when purchasing this.
Reply
Hi, I have AO Smith pump motor with the model number 7-177474-01. It is attached to pump model number 38448322.
Will this motor/pump have same size plumbing connections? And is it a suitable replacement?
Hi, I am looking to replace AO Smith pump motor with the model number 7-177474-01 and a pump model number 38448322.
Will this motor/pump work?
Plumbing connections same?
Reply
Will this be a good replacement for my Hayward model C48D31AO4 (SP2707Z1M) pump #SP2707X10?
My motor is going out,the pump is OK but is 8 years old and I think it would be wise to replace both as a drop in unit if I could afford the cost.What would you recommend ? Thanks
Reply
What is the GPM on this pump?
Reply
Hi, Jeff. The actual flow rate will be based on the Total Dynamic Head (TDH) of your pool.
Reply
Hi will this product (1 H.P. In Ground Pool Pump - PL1600) work as a replacement for the Hayward 1HP (C48K2N143B3 / SP1607Z1MBK) ?
Thx
Reply
Hi, Sally. Unfortunately, with the info provided, I'm unable to confirm if this pump will be a suitable replacement. You will need to provide us with the model or name of the pump housing or the Total Dynamic Head (TDH) of your pool.
Reply
I’m replacing a Centurion B852 Model Number 8-177214-24 would this be a suitable replacement?
Reply
Hello, I can look into this for you. What is the brand and the model of the entire pump you have?
Reply
I have a Hayward SP-2807 X 10 pump. The PL-1600 is said in FAQ to be a direct replacement for it. However, when I check flow rates, the Hayward pumps 75 GPM at 30 ft of head; while the PL-1600 specs show only 40 GPM for 30 ft of head.
Won't I be moving roughly only half the amount of water for the same time and energy cost with the PL-1600?
Reply
I am look for pool motor Hayward 1 Hp FR 78Y or some different model but with same qualification?
Hello Hildy. The Century Motors 1.0 HP Motor model USQ1102 is a compatible replacement for the Hayward motor model C48D31A04. Century 1.0 HP Square Flange 48Y Up Rate Motor - USQ1102 It is recommended that the motor shaft seal, backplate o-ring, and diffuser o-ring be replaced concurrent with the motor. Pump Shaft Seal 5/8" - - SPX2700SA PSR-200 Valve To Filter O-ring Id 6-3/4", Od 7-1/8" (gmx600f) O-263 Bulkhead O-ring - SX220Z2 Attached please find an exploded parts diagram for the Hayward MaxFlo XL Pump Series. Hayward MaxFlo XL SP2300X Series
Reply
