What is the warranty on the AO Smith variable speed
Reply
Hi Harvey,The motor is warranted against defects in materials and workmanship for one year from the date of installation or twenty-four months from the date of manufacture, whichever comes first.Thank you,
Reply
We have a Hayward Super II Pump Model# K45N2N104 S/N 8B05, 2hp, 1.55KW, 230 volts, RPM 3450 56J Frame. Can I purchase a ECM27CU for this? It doesn't look like a fit for the round flange. I know it should be the right motor, but I just want to be sure before I purchase it. Can I return it if for some reason it doesn't fit?
Reply
Brad, This 2.7 HP Variable Speed Motor Round Flange P/N ECM27CU can replace your current motor. We also recomend getting a Tune Up Kit which consist of the replacement shaft seal, housing gasket, diffuser gasket and housing lid o-ring.
Reply
Will this fit a Hayward Northstar pump? Do you have a vs motor that would fit a Hayward Northstar?
Reply
No, unfortunately, there are no variable speed motors that we know of that will fit the Hayward Northstar pump. There is a dual-speed motor that will bolt up with that Northstar pump.
Reply
3 questions, I think: 1) Can this motor replace the AO Smith SK1152? (1.5 HP) I don't see a compatibility list, or I missed it while searching. 2) Can you point all of us to a guide to choosing between the 2.7 and 1.65 HP versions--maybe a GPM rating or something of that sort. 3) Do you carry a pump/motor combo that uses this motor? If it doesn't fit my pump, I think I want this motor anyway. Thanks!
Reply
Hi James, This motor will not replace the SK1152 motor because the SK1152 shaft is keyed. The 2.7 motor has higher total hp and an interface with additional features. We have the PureLine PL2606 and the Jacuzzi 94026140 pumps that uses this motor.
Reply
Will this motor fit a Hayward RS 2000 2HP pump?
Reply
Linda, Yes this will fit a Hayward RS2000 pump as long as there are no height restrictions (clearance above the motor/drive). Be sure to replace the shaft seal when replacing the motor.
Reply
I purchased the variable speed motor and understand based on a manufacturer video that the timer controls can be taken off the motor and mounted separately with an adapter kit. Do you sell the adapter?
Reply
Part number 2512723-001 is the Offboard Mounting Kit.
Reply
I have a Hayward Super II pump model # sp3020eeaz with 3hp A.O. smith motor Type CX, PR Y56J (C face round flange). Will this fit?
Reply
Hi
I have a Hayward SP2607X10 with a 1HP motor C48K2N143B1. The motor housing is in bad shape – I can’t decide if I need a replacement motor or motor and pump – the pump appears fine.
I’m clear that I will to move to a variable speed motor for energy saving. I’m not wedded to Hayward. Will switching to a PureLine PL2605 pump provide me with anything different than if I went with the V-Green ECM27CU motor and stayed with the existing pump?
Thanks,
Lee.
Reply
Hello Lee, For a brand new SP2607X10 it would be 419.00, now for the motor would be 129.99, then the seal kit would be 37.95, and the housing would be 189.99 so if you are looking at all vs the whole pump; I would go with full pump. You would be replacing the motor, seals, housing. Still if the housing is the problem then that is just 189.99.
Reply
I have Jandy Stealth Series Model JHP2.0 pump. I may have to replace its single speed 2 HP motor, Century Centurion, A.O. Smith CAT B130. Can ECM27CU be physically connected to the pump body just like B130 motor? Can AquaLink RS control panel and its remote control, AquaLink RS PDA, control ECM27CU? Does ECM27CU have remote control?
Reply
Good morning Ali, Yes, This motor will fit. It has the same frame size and the controller will link with your aqua link system.
Reply
Does this motor come without the VFD & confirm it fits the Hayward Super II pump that currently has the 2 speed motor on it.
Reply
Yes, it fits the Super 2 and you will be able to control the frequency or RPM's.
Reply
I have 1 1/2 single speed hayward super pump (sp2610x15) will this motor fit my pump
Reply
Hi, Teddy. Yes, the ECM27CU VS motor will fit the Hayward SP2610X15 pump. However, if you're not going to replace your impeller or need the additional HP to match the 2.7 THP of this motor I would recommend the ECM16CU VS motor. I would also recommend getting the Hayward Super Pump Tune Up Kit GOKIT3 or GOKIT3SALT.
Reply
I would like to verify if the "2.7 HP Variable Speed Pool Pump Motor Round Flange" will fit my Super II pump. My current pump has gone out.
Reply
Hi Rich, yes this motor will mount onto a Hayward Super II pump. When replacing your motor we would suggest the Super II Tune Up Kit
Reply
Hi, will this motor fit a Hayward Super Pump Model # SP2615X20 ? Thanks
Reply
Hi John, Yes this motor will fit a Hayward Super Pump Model # SP2615X20. We would also suggest the Hayward Super Pump Seal Kit when replacing your motor.
Reply
I have a Century Variable speed pool pump with integrated timer (2517030 001 030 AD). The timer is no longer displaying information but the pump works fine. Can I get a replacement integrated timer? I only need the part that fits on top, four bolts and pigtail connection.
Reply
Hi, Tyr. The Century V-Green 270 User Interface - 2520652-001 is the part that you will need.
Reply
I plan to replace pool pump Model Hayward K48M2N110 , 1.5 HP motor. what are the choices in single speed or variable speed motor.
Do I need addition parts, replacement , Kits, etc.
can you let me know , thanks
Reply
Hi, Mohsin. The Century ECM27CU VS motor can be used to replace the Hayward K48M2N110 motor. I would recommend getting a tune up kit, bit we will need to know the model or name of the pump housing.
Reply
I have an existing 1.65 THP motor I would like to replace with a variable speed. Should I use the v-green 165 or is their any energy consumption advantage/ disadvantage in using the 270?...thanks, Vic.
Reply
Hi, Vic M. The V-Green 270 would be more efficient using the 1.65 impeller. The 270 motor will not reach the max load working amps.
Reply
what are the program set up requirements for a Goldline control system when you change to a VF drive ECM27CU?
Reply
Hi, Ronnie. To use the ECM27CU motor with the Goldline controller, you will need the V-Green Automation Adapter Kit - 2517501-001. For programming and wiring instructions see the V-Green Automation Adapter Kit Manual.
Reply
I have a Jandy Stealth Series Model JHP2.0 pump controlled by my Jandy Aqualink RS controller.. Will this motor work on my present Aqualink RS controller or do I have to upgrade my Aqualink RS contoller board for this VSP motor to work. My present controller was installed back in 2005. Thank you.
Reply
Hi, Johnny. You will no need to upgrade your Aqualink RS; however, you will need the V-Green Automation Adapter Kit - 2517501-001.
Reply
Helo
Inyo pool
I am going to variable speed from single speed. I need replacement motor . Could please help me this ? Is it work with current equipment . I attach photo for all equipment
I appricate you help
Thanks
Hi, Sanjay. This ECM27CU is the correct motor for your current pump. You will also need to get the Super II Pump Tune Up Kit - GOKIT2 or GOKIT2SALT. You can use the RS-485 Network Connection or purchased the V-Green Automation Adapter Kit - 2517501-001 if you have available relays.
Reply
Hello, I have a Hayward Super II K48N2N104 (SP-1620-Z1-BE) pump and looking to replace with variable speed. I see where you recommend the ECM16CU and also the ECM27CU. Mine is 2hp, is the 1.6 sufficient or do I need to go to 2.7?
Reply
Hi, Dave. This ECM27CU is the correct variable speed replacement option. You will also need to get the Super II Pump Tune Up Kit - GOKIT2 or GOKIT2SALT.
Reply
Did you end up replacing the Super II (SP-1620-Z1-BE) w/ the variable speed 2.7 HP motor - checking what your experience is
Reply
My Hayward single speed pump motor needs to be replaced. I would like to replace it with a variable motor. Can you please confirm which one is the appropriate motor. I am attaching pictures. Also, please let me know what additional parts I would need for this replacement. Finally, do you have any videos, literature that would be of help to me in doing the work. Thanks.
Hi, P. James. This ECM27CU - V-Green Variable Speed Motor along with the GOKIT2 or GOKIT2SALT are the parts you will need to make the conversion. You can check out our How To Replace the Motor on Your Pool Pump guide.
Reply
You told me this motor will work to replace my current k48m2n110 motor But you didn't say anything about the housing. Do I need to replace the housing too or just get the repair kit? I can't seem to find any numbers except patent number.
Reply
Hello, In order to find the correct seal kit for your pump, we will need to know the model number of the pump. You will only need to change the motor with seals, unless you have a crack in the pump somewhere.
Reply
You told me this motor will work to replace my current k48m2n110 motor But you didn't say anything about the housing. Do I need to replace the housing too or just get the repair kit? I can't seem to find any numbers except patent number.
Hello, You would need to change the seals with the motor. You would want to change any housing pieces only if they are broken. In order to find the correct seals for you, what would be the model number of the entire pump? If you are unsure, you can send a picture of the entire side view of the pump so we can identify it for you.
Reply
Hi,
I have an old Hayward NorthStar SP4010X20NS I took out of service because a) it was screaming when turned on and b) it was an energy hog and I replaced it with a VS pump. But I have this old NorthStar on my workbench and I am considering the VS motor replacement for use as my water feature pump.
Will this motor fit the NorthStar wet end ok? Any issues with doing so? And before I drop $700 on this project, is a wet-end likely to last forever?
Thanks for any insight.
Reply
I have a Jandy Stealth Pro SHPF2.0
Is this the right motor for it? What other components do I need to buy to do the install?
Reply
The variable speed motor replacement is the model ECM27SQU and if you click here you will be directed to the parts diagram for your model pump. Keys 5, 13 and 15 are the most commonly replaced seals with this pump. You will need the pump housing serial number to confirm which shaft seal you will need.
Reply
Can I use a ECM27SQU in place of a ECM27CU?
Reply
Unfortunately no because the SQU has a square flange motor face and the CU model has a round motor face. The model of the front pump housing that the motor bolts to will determine the motor that is compatible.
Reply
I just purchased the ECM27CU as a replacement for my 2 speed 2 THP SP1615ZSC. It is a Hayward Superpump SP2615X202S. I also ordered impeller/diffuser kit 5110-102 and GOKIT3SALT. Are these all the correct parts ? I am attaching photos
Hello - The impeller and diffuser kit, 5110-102, is compatible with the Super II and not for the Hayward Super Pump shown in your pictures.
Reply
Hello, I have a Jandy VS FloPro 2.0. Recently I've been getting messages on our control pad that say "Fault Hardware Limit" and "Fault Low Voltage" and our pump will not power up. Do you know if the problem is only with the motor or the entire pump? If I only need the motor, will this item work with the Jandy VS FloPro 2.0?
I need to replace an A.O. Smith RS1500 motor. I've seen from other questions that this will work. But is it worth 3 times the price in energy savings? And how hard is this ti wire in? Will I need an electrician or can I just replace motors and re-hook up the wires? Thanks for your help.
Reply
Hi, Michael. To determine if the variable speed pump is worth the cost, you will have to calculate the Total Dynamic Head (TDH) of your pool. An electrian is not needed if you know what you're doing. You can use our How To Wire A Pool Pump guide for directions.
Reply
I have a Jandy JHPU2.5 HP single speed pump for a 1.9k Gallon pool + Spa + Cleaner+Pentair 60 DE filter, and the piping is 2". I was told the 2.5 HP is too big for my use, with the SWG system.
Can I use this motor as replacement or should I consider the 1.6 HP VS V-green? I also have a Zodiac Aqualink RS8 automation. Can this motor with the automation system?
Reply
Yes, this motor would be suitable replacement for your application and in order for this motor to communicate with your automation you would need part number 2517501-001.
Reply
Hi I have a Hayward dual speed 2.5HP (SP3020X252AZ) and is looking to upgrade to a variable speed. Is this the right model & if there are other parts that I need to get? Please also recommend a higher HP with variable speed (3HP + parts).
Thank you!
Reply
Hi, David. This ECM27CU along with the Super II Pump Tune Up Kit - GOKIT2 or GOKIT2SALT are the parts you'll need. There is not an option with higher horsepower.
Reply
Thank you Lennox. Just to be sure & before placing the order, the proposed ECM27CU motor can match up to the existing Hayward mounting plate (SP3020X252AZ)?
Reply
My energy company offers a discount for replacing single speed with variable. They said I can replace just the motor with an Energy Star certified motor on my existing pump. Is this motor Energy Star certified?
Reply
Hi, Jeff. Variable Speed Motors only do not qualify for any energy company rebates, ONLY complete pumps.
Reply
I have a Hayward Super Pump 2610x15. I believe this exact variable speed motor will work with my pump. My question is...do I need to do any upgrades to the diffuser or impeller being that my pump is 1.5hp and this one here is capable of up to 2.7hp?
Reply
You would need to change the impeller and diffuser if you are trying to get the full strength capacity out of the motor however that is a significant increase so more than likely you will not need that.
Reply
Does th ECM27CU come with a base
Reply
John, no, the V-Green 2.7 HP Round Flange 56J Variable Speed Motor - ECM27CU does not come with a base. As long as the FR is the same as your old motor the ECM27CU should fit your existing base.
Reply
Will this motor work on a 3 hp super pump ll SP3025X30LZ
Reply
John, yes, the V-Green 2.7 HP Round Flange 56J Variable Speed Motor - ECM27CU would work as a variable speed replacement motor for your SP3025X30LZ pump.
Reply
I have a hayward super pump 2 sp3025x30az impeller is spx3021c. Is there a different impeller that will give me more flow? Motor is V Green 270. I would like to run at a lower RPM.
Reply
Would this motor replace the motor in my Jandy HHP 2hp x56j? Will the motor work with my Jandy automation system with the added automation adapter?
Reply
Hi, Bob. Yes, this motor is compatible with your pump and Jandy automation system.
Reply
I was referred to this motor as a direct replacement for my Hayward Super Pump motor. Should I also purchase a larger impeller and diffuser?
Hi Ed, To take advantage of the upper Horse Power Range of this motor we would suggest upgrading to this 2.5 HP Impeller this 2.5 HP Diffuser and this 2.5 HP Seal Plate. Also when replacing your motor we suggest this Hayward Super Pump Tune Up Kit We hope this helps, we also have a lot of videos which will walk you through the installation process when you tackle this job.
Reply
At this point, wouldn't it make sense to buy an entire pump and plumb it in? Its a small fortune after add all those items. I have the same super look to upgrade to vs.
Reply
Hi Ed, when the pump housings are still in good condition then most often replacing the motor and parts is still more cost-efficient than replacing the entire pump. However, sometimes its just a preference.
Reply
Would this motor be a suitable replacement for a Pentair Intelliflo VS-3050? The part number of the existing motor is 353014.
Reply
I have a Jandy Pump JHPU 2.5 and a Century motor Cat B130 P/N 0-159988-06, 2.0 HP, Frame X56J, 230 Volts, 10.5 Amps. I calculate at 8 cents per KWH, at 8 hours per day, it costs $556/year to run this motor. Regal Beloit told me the alternative pump to use is ECM27CU which you have on your website for sale. Can you tell me:
1. Is this compatible with my Jandy Pump.
2. Would changing the pump/impeller reduce the noise/reduce cost of elec.
3. Cost to run ECM27CU 8 hrs/day at 8 cents/KWH.
Reply
Hi, Tony. Yes, this ECM27CU motor is compatible with your Jandy pump. Changing the impeller will not reduce the pump noise. Th is motor use 2.4 kW at max RPM's, so it will cost $1.54 to operate at $0.08 / kWh.
Reply
I have seen a recommendation to use the Tune Up Kit Hayward Supper II-GOKIT2 and also the Impeller 2.5 THP-SPX3021C. I believe both are Hayward brands. How is this used with the ECM27CU Century Motor if not a Hayward brand? Lastly, I don't understand how a variable pump saves money. If used at lower RPMs doesn't it take longer for the water to circulate effectively requiring a longer time and hence just as much energy? This may require a phone call, if so, let me know and I will call you.
Reply
Tony, Motors can be used on several different pumps, Kits and Impeller are used on specific pumps. Your pump uses the Jandy JHP / JHPU Series Pump Tune Up Kit - GOKIT77. A variable speed pump save energy When the RPM's are reduced water flow is reduced, however, the energy used is less. In some case, the extended run time still will be less.
Reply
Thanks for the response!
Reply
My system is setup for dual phase, does it matter that this is single phase?
Reply
Hi Sean, In the USA there is typically Single-phase and Three-phase electric. Single-phase electrical is normally used in residential applications and Three Phase is used in Commercial Applications. I'm not aware of Dual-Phase. Is it possible you are meaning Daul-Speed meaning your pump runs on a high and low Horse Power? Please click the reply link below to give further clarification, thanks so much!
Reply
I have a Hayward SP3015X20AZ that was installed brand new in September 2019. It is the loudest motor I have ever owned, even louder than the old motor. What parts will I need to replace this with the V-Green 2.7 HP and can I expect it to be quieter than my current motor?
Reply
Hi Dwight, Yes the Variable Speed will be so much quieter. I have one on my pool and when it was first installed I thought it had quit running because I couldn't hear it. You would require 2.7 Variable Speed Motor listed on this page as well as Hayward Super II Seal Kit I would also suggest replacing your 2 HP Impeller with this 2.5 HP Impeller so you can take advantage of the higher HP range of this Variable Speed Motor.
Reply
Did you notice a change in your electricity cost from before and after? Just trying to weigh the pros and cons before making this type of purchase versus a new complete VS pump.
Reply
Yeah I did notice a big decrease in our power bill. Here is an article we wrote which explains the operational cost savings you can expect. Click here Article on How Much Does a Pool Pump Cost to Operate
Reply
Can this motor be wired to work with a Jandy AqualinkRS controller? This controller was installed in 2005 and has not been updated since. Thanks!
You would need to order The V-Green Automation Adapter provides the ability to operate a V-Green motor with a 3rd party automation system such as the Hayward Goldline Pro Logic, Pentair Easytouch, Jandy Aqualink, and Intermatic controls. This will allow the user to control and experience the full variable speed capability of a V-Green product through an existing automation system. V-Green Automation Adapter Kit - 2517501-001.
Reply
I have a Hayward Super II pump, model #SP3015EEAZ, and a newer replacement A.O.Smith/Century motor, model # ST1302V1, 3.0 HP and SF=1.0.
I had upgraded/upsized the impeller, diffuser, and seal plate when the original 1 1/2 HP motor was replaced by the newer 3.0 HP A.O. Smith motor about 5 years ago.
Would I need to change out these components again when I install a new V-Green ECM27CU 2.7HP variable speed motor?
Reply
Hi Anthony, I took a look at your last order and the 3 HP impeller you have would be just a little too strong for this motor. To use this variable speed motor on this page you will need to swap out your 3 HP impeller with this 2.5 HP Super II Impeller Kit also when you replace the motor you will need this Hayward Super II Seal Kit. This variable-speed motor will save you a ton on your operational cost compared to your 3 HP single speed motor.
Reply
Patrick, I see that I had ordered and installed a SPX3025CKIT Impeller Upgrade Kit in 2016 along with my current 3 HP motor. Is this the same kit that is needed for a ECM27CU 2.7 HP pump?
Reply
Anthony, Nice catch I did put in the wrong link, you will need this SPX3020CKIT 2.5 HP Impeller Kit Sorry about sending the wrong link the first time around but super happy you caught that =)
Reply
Thanks, Patrick! I will get the motor and accessories ordered in the next day or two
Reply
I have a Jandy PHPU2.0 would like to get this VS pump but also need a new salt chlorinator I currently have a Jandy AquaPure700 but the electronic control panel is broke. What are my options what will work together what do I need. I have a quote # 69391 for the pump and gaskets and for the V-Green Automation Adapter Kit - 2517501-001, which I do not know what this piece of equipment does. Ive been on chat 5 times to figure this out but keep getting disconnected before my questions are answered.
Reply
Hi Bob, Thanks for the question and sorry about getting disconnected from chat. Do you have an automated control system which controls all of your pool equipment something like the Jandy Aqua Link which has an indoor controller? This will be important for us to know so we can suggest the proper items.
Reply
Hi, No I do not have an automated control system just a Intermatic dial timer that turns the pump on/off.
Reply
Thanks for the updated 69391 estimate. Is it possible for me to automate the system if yes then what would i need to do that?
Reply
Hi Robert, On board controller on the motor will allow you to automate the pump. For example you set when the pump comes on and off and you can automate at what speeds the pump runs at during different times of the day. If you want full automation where you would control things like your pool lights, valves, heater, spa, spa blower, etc.. from inside your house then that does get quite a bit more expensive. To quote we would need to know if you have a pool only or pool and spa combo. And which equipment you would like to control.
Reply
I have a Jandy JHP 1.5 in a salt pool what do I need to install this motor part wise??
Hi Joe, you will also need the Jandy JHP pump seal kit when replacing the motor
Reply
what is the spec on the bolts to connect the the motor mounting bracket to the motor. My old ones dont fit and I need to buy 4 new ones.
Thanks
Reply
Hi Michael, for us to suggest the proper bolts could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo or quickest provide them using our live online chat feature. Once we get this photo we can make the proper recommendation for the bolts.
Reply
I would like to replace this with your V-Green 2.7 Round Flange motor. Can you supply me with all the part numbers I will need to upgrade this original 1994 1.5hp pump? I have a water feature in this pool and the 1.5hp just barely cuts it, however I'm sure I'll need more than just the motor. Thank You
Hello, yes, this is the correct replacement motor for the motor included in your photo. You will also need a Hayward Super II seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I am thinking about replacing my older motor for my pool will this motor work with the CareTaker cleaning system?
And is it compatible with my pump?
Hi Mike, yes, this is the correct replacement variable speed motor for the motor included in your photo. You will also need a Hayward Max Flo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Hi!
Currently, I have a Hayward Super Pump that runs on 220V model C48L2N134B1 SP-1610-Z1-M 1.5HP. After doing some research, I should be able to swap my old motor with this Round Flange 56J ECM27CU. I was told my direct replacement was ECM16CU but I would rather use this one because of the user interface and power. Will that be ok?
Btw, thank you for your YouTube video. That video actually brought me here to his site.
Thank you,
Noel
Reply
Hi Noel, yes going with a stronger variable speed motor is okay as you can always dial down the RPM setting to match your application needs.
Reply
Does this motor's timer support different schedules on the weekend versus during the week?
I have a Hayward Super II pump. Will this motor fit that without any extra parts?
Attached is a pic with my current motor's specs? Is the V-Green motor compatible with HP and Frame?
Yes, this is the correct variable speed replacement motor for the motor included in your photo. You will also need a Hayward Super II seal kit when you replace your motor. You can set up the schedules in 24 hr intervals. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Is this the correct pump to replace A.O.Smith SP3215Z1BE / 1.5HP / Y56YFrame
Reply
Hello Bill, yes this motor would replace your Motor, 1-1/2hp Full Tristar 115/208-230v (SPX3215Z1BER, HSQ1152, SP3215Z1BE, SPX3215Z1MR, SP3215Z1MR since your motor has a total HP of 2.4 THP.
Reply
I have a Hayward Super II pump, model SP3015X20AZ, and a Century motor, model SP1615Z1MBK / C48M2N111A3. Judging by the other responses, I think I can use this motor, with the GOKIT2SALT Hayward Super II Saltwater Tune Up Kit (I have a saltwater pool) and the SPX3021C 2.5 HP Impeller. Did I get that right? Thanks for all the help!
Hi John, yes this variable speed motor, seal kit, and impeller are correct for your application.
Reply
Will this motor mount directly on a Whisper Flo WFE 6 pump? Is 48Y>56Y spacer included with motor?
Reply
Hello Ken, yes the ECM27CU would be the replacement motor for the WFE 6. It does come with the base spacer for the install.
Reply
Will this fit a a 2hp Pentair Whisperflo
Reply
Hi Frank, Yes this will fit a 2hp Pentair Whisperflo. Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can let you know if your impeller would need to be changed.
Reply
Looking to replace a Century B230SE. Would this one work with a Hayward SP0320X252AZ pump or would I have to swap that out, as well?
Thank you for contacting Inyo Pool, V-Green 2.7 HP Round Flange 56J Variable Speed Motor - ECM27CU will work. You do not need to replace the housing.
Reply
Hello, could I wire this without the automation adapter even though I have the jandy aqualink and RS4 indoor controller from 2004. Just have it always turn on full speed, then I can adjust it at the pump if I need to slow it for filtering.
Hello Dennis. The Century Motors V-Green 2.7 HP Variable Speed Motor ECM27CU can be wired through the Jandy AquaLink with constant power being provided to the ECM27CU allowing the internal timer to operate per the programming set in the control module, independent of the automation.
Reply
Running the M48AA69A01U/ECM27CU pump with Super II. LCD lights on controller but no characters display. Pump is is still working well in terms of on/off per schedule. Is the controller for this unit available?
Thanks,
Hi Charles, this V-Green 270 User Interface - 2520652-001 will replace your non-working display. It is not currently in stock but we hope to have it again soon.
Reply
Will ECM27CU 2.7 HP VS motor be a replacement for Hayward pump SP2615x20 with single speed Century 2 HP motor K48M2N110C2 for not to big fiber glass pool with solar system (on top of 2 floor roof) ? Thanks
Hello Sunny. The Century Motors V-Green 2.7 HP Variable Speed Motor ECM27CU is a compatible replacement for the Hayward Super Pump SP2615X20. The flexible programming options of the ECM27CU will allow you to tailor a running schedule to address the two-story solar usage and decrease RPMs to conserve energy in times when solar activation is not desired. The fact that you have a 2.0 HP motor currently installed indicates a minimum horsepower required to send water through the two-story solar panels. It is recommended that the motor shaft seal, seal plate gasket, and diffuser o-ring be replaced concurrent with the new motor. The GOKIT3 contains the necessary parts to complete this project. Tune Up Kit Hayward Super Pump - GOKIT3
Reply
My current motor has a 56Y frame (square). Will this fit, knowing that it has a 56J (round) frame?
Hi Jean, this will not replace your 2.4 total horsepower SP3215Z1BE motor. You would need the V-Green 2.7 HP Square Flange Variable Speed Motor - ECM27SQU. The variable-speed motors have a smaller (48) frame but include a spacer to add to the motor mount to make up the difference in size.
Reply
Would like your input to make sure I order the correct variable speed motor?
See enclosed photo of exciting motor currently in use.
I should order V-Green 2.7HP - Round Flange 56J -ECM27CU?
Pump itself is Haward Super Pump 2.
I have new complete seal kit for the new motor installation.
Line voltage 240 Volts (no load)
Max amps = 10.8
Pool cleaning system Caretaker 5 Port w/ 1 1/2" supply lines
Average GPM per circuit = 60 +/- 1-2 gallons
Your thoughts please thank you.
Hello Scott. The Century Motors V-Green 2.7 HP Variable Speed Motor model ECM27CU is the correct model for the Hayward Super II Pool Pump. Your current motor has a total horsepower of 2.5. The ECM27CU total horsepower is 2.7. Attached please find an exploded parts diagram for the Hayward Super II. Please be sure that you have all the seals and gaskets contained in the GOKIT2 when replacing the motor. All parts contained in the GOKIT2 are available individually. Hayward Super II GOKIT2
Reply
Sorry to ask a question that might have been answered already, but I need to replace the motor for my Hayward SP2615X20. I was looking at the single speed replacement (UST1202?). Can you confirm if this is a replacement option and tell me if a larger impeller is also required? And would the additional cost be offset by lower electrical consumption? Thanks
Hello Bill. The Century 2.0 HP Round Flange 56J Up Rate Motor - UST1202 is a compatible replacement motor for the Hayward motor K48M2N111. The rated total horsepower of the 2 motors is almost identical, no impeller change is required. The Tune Up Kit Hayward Super Pump - GOKIT3 contains the necessary seals and gaskets to complete the motor change.
Reply
