How do I change the shaft seal on my pool pump?
Reply
Changing the shaft seal is quite simple. Here's How To Replace a Pool Motor Shaft Seal.
Reply
Which side goes where when I replace this 201 shaft seal?
Reply
When replacing this 201 shaft seal as well as others you need to put the spring side on or against the impeller with the dark ceramic side out and then the other half of the seal inside the pump seal plate with the white ceramic side facing out. Please be advised not to touch, wet, or dirty any of the ceramic parts for it very well may compromise the seal.
Reply
IIs this the correct seal for purex aquatron pump?
Reply
Hi Fred, No this not the correct seal for the Purex Aquatron Pump, you would need this Purex Aquatron Pump Seal.
Reply
I bought this along with a motor. I have setup watching your diff videos. It is a JWPA Sta-Rite pump. After hooking everything up and turning it on, there is water coming from the backside of the impeller so the seal is failing. I did have a VERY hard time getting the seal onto the impeller and I'm not sure the spring is actually able to move properly. Should I lubricate the impeller to help slide on the seal, and if so, with what (not the seal itself, but the impeller to help slide on).
Reply
Brian, Lubricating the shaft/inside of the impeller with a silicone lubricant where the shaft seal goes will make it easier to install the seal. You may need to install a new shaft seal since its leaking.
Reply
How to get pump separated from motor, I have a motor model s48874a03 and pump model jwpas5f-2a4
Reply
While this video and instructions are not for your exact pump, it still covers all the steps needed to remove a motor. Please click "How to Replace the Motor on Your Pool Pump"
Reply
The shaft is leaking on my above ground pump. The parts tag on the pump shows the following: A.O. Smith HP: 1.0 SPL part # 7-187609-21, serial number BW6-22, SP W48Y. 60HZ, RPM 3450. The wet end has the following tag: Jacuzzi model S1kG9-3, order no. 94027976NB0X, Date 15 Jun 01. I did not install the pool so I do not have any information about it. What shaft seal part should I purchase?
Reply
Hi, The Jacuzzi S1KG9-3 uses a Pump Seal 200 (PSR200).
Reply
Does it met for ITT Marlow pump SDA75?
Reply
The number you provided does not allow me to pull anything up. If you are looking to replace the shaft seal on your pump please attach a picture of your pump so I can identify what you have.
Reply
have ust 1152 pump motor need ceramic seal pump seal 201 will that work on mine
Reply
Bruce, The shaft seal is dependent on the pump housing not the motor. Please provide the make and model of the pool pump.
Reply
I have a Hayward pump model SP3110X152GH, had the seal replaced a year ago. they installed PSR Seal 201V... it lasted less than a year, the rubber split that's part of the compression spring.. this is the second time, Is leslies pool using the correct seal?? Fred
Reply
Hi, Fred. The Hayward SP3110X152GH pump uses a PSR-201 Pump Seal.
Reply
I have an AO Smith UST1072. I bought a PS-201 seal that doesn't fit the shaft. The original seal on the shaft had notches for two metal pieces extruding from the bottom of the shaft. Is the PSR-201 the correct seal for this shaft instead?
Reply
Hi, Tony. You will need to remove that metal piece in order to get the new pump seal to fit onto the impeller shaft.
Reply
How do I install PSR Seal for pool pump motor?
Reply
Hi, Lonnie. You can use our How To Replace a Pool Motor Shaft Seal guide for installation steps.
Reply
I have a A.O Smith replacement - Century pump 1081/1563.... Part 7-184821-04 Need to replace the shaft seal...
What part number is this?
thanks,
Reply
Hello Deryk, the part 7-184821-04 cross-references to 3 HP 2 Speed 230V Low Amps Thru Bolt Motor (3421821) - BN62. If you need shaft seal, we would need to know the pump model number in order to assist you with finding your correct seals.
Reply
I need a new motor and shaft seal or seal kit for my Pearl whirlpool, but I can't find the seal on your site. The motor is MagneTek .7 HP (1.0 SF) 7-177954-23 which I believe your BN24 will replace. The pump label does not list a brand name. It reads: 7JCM-TL-3-BULK, model 94216710, date 30OCT98. Can you please verify that I selected the right motor and tell me which seal will fit. Thanks, Danial
Reply
I'm looking for the replacement shaft seal for a Hayward #07713chcl030281077. That's the number I got off the pump motor. The number off the housing is sp2810x15. Can you help find the right seal?
Reply
Hello, With the model number provided this the tune-up kit you will need,http://www.inyopools.com/Products/00500022000633.htm
Reply
I HAVE A JACUZZI MAGNUM FORCE PUMP. THE SEAL IS LEAKING WHERE THE MOTOR JOINS THE PUMP. I NEED TO KNOW WHICH SEAL TO GET
Reply
I have 3/4 hp booster pump, [magnetek], for swim pool. I have leak where pump shaft enters impeller. I found cracked/dried out rubber washer I think was the seal or part of seal. Not sure?? I'm having trouble finding what type seal I should use. I will send photo of motor name plate. Motor is working fine.
For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply your photos simply click the reply link below and upload your photos. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
What shaft seal kit do I need for Pentair Superflo VS pump? Apparently not the same one as the regular Superflo.
Hello Troy. Pentair recommends the OEM shaft seal, Pentair part number - 354545s, or an alternative shaft seal, part number PSR - 200. Pentair Shaft Seal 5/8" PSR-200 - 354545S
Reply
