Revived impeller #C105238PB and it says 1 1/2 HP Impeller? This parts list says 1 HP and that's what I need. SEE previous question request for addition comments on this part and order. I have requested a return and I really need an impeller please
Reply
Hi, Doug. The C105-238PB impeller is rated for a 1HP Full Rate or 1-1/2HP Up Rate motor.
Reply
I am replacing the motor on my sta-rite P6RA6G-207L with a 1 1/2 HP uprated Century USQ1152 motor. The original impeller is a C105-238P and is a "bolt on" style. The shaft on the new motor is a "spin on" style. Is this the correct impeller to replace it in my pump housing? Will it fit?
Thanks for taking my question.
Reply
Hi, Bob. To convert the pump from 2 hp to 1-1/2 hp you will need this Impeller - C105-238PB, Diffuser - C1-271P1 and the Tune Up Kit - GOKIT79.
Reply
In changing my motor how do I remove and replace the impeller? How is it attached to the motor?
Reply
Hi, Stan. You will have to lock the motor shaft, remove the impeller screw and then remove the impeller. You can see how this is done in our How To Replace a Sta-Rite Max-E-Pro Pump Impeller guide.
Reply
we have a Sta-Rite pool pump 1 HP, model P4E6E-151L, Code 1C95E (old style (pre-1998)
The impeller is screwed onto the shaft and we are looking for a new one. From the details I've seen this is not detailed, can you help answer this issue.
Thanks
Reply
Hi, John. The correct impeller is Part # C105-238PB.
Reply
I have a impeller that was touching the inner part of the diffuser that had corroded: any readon for corrosion? I put acid in small quantity pump down.
I need to change impeller and diffuser: which references please. Motor indicates: P6RA6E 205L. thank you
Reply
Hi, Sebastien. The Impeller - C105-238P and Diffuser - C1-271P1 are the parts needed for the P6RA6E-205L pump.
Reply
Does this impeller fit for STA-RITE MAX-E-GLAS II P4E AND P4E62 series pump 1 1/2 HP
Reply
Hi, Jimmy. This impeller can be used with the following models that is close to the partial number provided, P4E62E-187L or P4E62E-151L. I will need the complete model number of your pump in order to confirm.
Reply
I would like to rebuild my P4EA6F-187L, replace motor, all seals o-rings, and impeller. Is this the correct parts?
- GOKIT38 seals
- SQ1152 motor or USQ1152 motor?
- 5055-11A
Reply
Hi Steven, Yes this is the correct parts list. For the motor, you can go with either the USQ1152 1.5 HP Uprated Standard Efficiency Motor or the UQC1152 1.5 HP Up Rated Energy Efficient Motor. The Energy Efficient Motor will cost about 20% less to operate.
Reply
I noticed these are all 48Y frame motors. The Sta-Rite pump has a 56Y frame motor. Do the 48Y frame motors ship with a conversion pad?
Reply
Hi Steven, Yes the 48Y motors do come with a rubber spacer pad.
Reply
I have an HSQ125 motor which is 1.25 HP 1.00 SF. What impeller and diffuser I have to add to the cart?
Reply
Hello, What is the brand and the model of the entire pump so we can look into this for you.
Reply
I have a Sta-Rite Model P4E6E-187L Need Impeller 1.6hp of the elect motor Do I order the impeller for 1 to 1.5 hp Impeller;
I will also need a seal assy
Would you have information on haw to install the seal assy
Reply
The impeller I have is C105-92P. Will the impeller your company put forward to me work?
Reply
Hello Ty. The Sta-Rite Impeller model C105-238PB is NOT the correct impeller replacement. At one time your impeller contained the additional identification mark of "R" or "S". Sometimes the R or S was handwritten with a grease pen. The key in proper impeller identification is the motor Horsepower (HP) and Service Factor (SF) identified on the motor's label. If your motor is a .75HP, the C105-92PS impeller is correct. If your motor is a .5HP with a SF of 1.3 or greater, the C105-92PS is correct. If your motor is a .5HP with a SF of 1.25 or less, the C105-92PR is correct. Dura-Glas Impeller For .75 Up rate (.5 Full Rate) C105-92PS DURA-GLAS 1/2HP UP RATED IMPELLER - C105-92PR
Reply
My impeller has part #C105-238PB on it but doesn’t exactly match your picture of that part. Mine has a metal part attached to the shaft with two bumps in it that mate with the shaft seal. Will yours work or do I need a different impeller. I attached a picture of mine. Thanks for your help.
Hello Alvie. The Sta-Rite Impeller C105-238PB is the direct replacement for the impeller identified in the photo provided. The metal part that you reference is a part of the old shaft seal, underneath is a rubber ring, also a part of the old shaft seal. These items are not a part of the impeller construction. When replacing the impeller it is recommended that the motor shaft seal, seal plate O-ring, and diffuser O-ring be replaced at the same time. The GOKIT38 contains the parts necessary to complete this project. Tune Up Kit Sta-Rite P4E & P4EA Max-E-Glas II / DuraGlas II - GOKIT38
Reply
I have a Sta-Rite Pump Model No: SNC-L. Motor Model: C48H2EC11C3. 1/2 HP 115/230 volts. I need to replace the impeller. Is this the correct impeller and if it is, are there additional items I will need when replacing the pump.
Reply
Hello Lisa. The Sta-Rite Impeller C105-238PB is installed on the Sta-Rite Max-E-Pro Pool Pump. The Sta-Rite Pump Model SNC-L cross-references to a Sta-Rite Shallow Well Jet Pump. Please verify this is the correct pump in your query. The following parts would be specific to the Sta-Rite Pump model SNC-L. Impeller - Impeller, J105-40p (j105-40p) Shaft Seal - Pump Shaft Seal 5/8" PSR-100 Seal Plate Gasket - Gasket, Seal Plate, All Hi- Head (stn20-35) It is recommended that the motor shaft seal and seal plate gasket be replaced concurrent with the new impeller.
Reply
