Is the 238P and the 238PEBA interchangeable.. I have the USQ1202 motor and am wondering if the 238P (from old motor) is sufficient
Reply
Hello Ron. Unfortunately they are not interchangeable. The 238P is listed as 3/4 to 1 HP , while the 238PEBA is for a 2. to 2.5 HP. The UST1102 motor is a 2 HP , so please go with the C105-238PEBA
Reply
I just got my UQC1102 motor to replace my original K48K2PA105C1. Which impeller is right -- C105-238P or C105-238PB? What is the difference or could I use either one? Thanks.
Reply
Hi Ed, The UQC1102 is a 1 HP uprated impeller so you would require this C105-238P impeller as it is used for a 1 HP uprated motor.
Reply
have impeller for sta rite part#105-137p eb what impeller do I need either a 1 hp or 11/2hp motor
Reply
Hi Ron, The 1HP Full/1.5HP Max Rate Impeller (C105-137PEB) would be the correct impeller needed.
Reply
Hello I have a Sta-Rite Model P458E-1561L Code: 1F93M pump and motor that motor is bad and looking to replace it. Also have Pump Impeller #C105-238P I understand it is for a 1Hp uprated motor, but not sure just what that means? lol I still don't know witch motor it will require because nothing is showing for Model P458E-151L so not sure motor will work with pump housing and brackets..And it is also looking like may need new impeller as well, so any suggestions on motor and impeller sets?
Reply
Hi Tim C., The USQ1102 will be the correct replacement motor. Up-rate is just a term used for motors that operate at the rated hp. The C105-238P Impeller will also work with the USQ1102 motor, I would also recommend getting the Sta-Rite Max-E-Glas II / DuraGlas II Tune Up Kit.
Reply
I have a Sat-Rite 3/4 hp model # P6E6D-203L pump that has a broken impeller.
How does the impeller come off the motor shaft?
Reply
Hi Gary, Here is a Guide on How to Remove a Pool Pump Impeller which will walk you through the process.
Reply
I am wanting to rebuild my sta-rite max-e-pro p6e6d-205L pump motor, how do I pick the right 3/4 hp motor, impeller, diffuser, o-rings.
Reply
I have a Sta-rite P6RA6G-207L 2HP pump/motor and was replacing the motor when I found the impeller scored. It is stamped C105-238P. I see several with the same number but different letters eg. PB, PEBD. etc. Do you know which impeller is the correct model for my pump/motor. Tks
Reply
Hi, Rod. The correct impeller for your model pump is Part #C105-238PDBA.
Reply
I replaced a Sta-Rite P4E6E-1871 single speed pump with a Century V-Green 1.65 HP VSP ECM16SQU using Go-KIT38. It appears that it has started to melt the plastic on the impeller (see pic) after installing the new shaft seal. I removed a metal sleeve that was part of the old shaft seal on the impeller according to the video instructions on installing the V-Green 165. The impeller is C105-238P. Which new impeller type should I buy and was removing the metal sleeve incorrect?
Hi, Mark D. The correct impeller based on your pump model is P/N C105-238PB - Impeller 1.5 THP.
Reply
I have a 1.5 HP pump motor. The current impeller is marked C105-238P I'm not seeing that combination listed anywhere. (most have another letter with the "P" such as "PB") Will the C105-238P work with a 1.5 hp? Thanks
Reply
I was able to locate that impeller. Please click here to view the C105-238P. If you need a different impeller you will need to confirm the front pump housing wet end model that the motor attaches to and the actual motor model, part or catalog number.
Reply
The motor is a CENTRY 1.5HP ,3450RPM8.0/16.0AMPS ON A 56YFRAME
Reply
Could send a few photos as those are always helpful. If you send photos then take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get any of this information we can make the proper recommendation.
Reply
