should I use an adhesive compound to hold gasket hwsp 1600-s in place?
Reply
Negative. Do not use an adhesive on this gasket. Just standard o-ring lubricant. One type is magic lube.
Reply
If I order this product, do I also need gasket cement and if so what do you recommend ?
Thanks
Reply
Hi. You will only need to use a little Magic Lube O-ring Lubricant - 630 when installing this o-ring.
Reply
I need a new gasket for Hayward super pool pump. SP 2607X10. I bought what I thought was correct a year ago, it doesn't fit. I find SP's but not the SP 2607X10.
Reply
Hello, the pump that you have is the SP2607X10. For the gaskets, you can either go with the GOKIT3 or the GOKIT3SALT.
Reply
I ordered this gasket and it is about 1/2 inch to large, I've looked and can't seem to find the correct one. I had ordered a kit that was for Hayward super pump series 1600,2600,2600x and I thought based on the measurements the one I ordered which was item number 5110-04 was supposed to be smaller than the first one but they are both the same size and both are slightly too large to seal. Is there one smaller than this one?
Reply
Karen, It sounds like you have the correct gasket for the Hayward Super Pump. The gasket is slightly larger so it has to be worked into place for a tight seal.
Reply
How do I get the cover?
Reply
Hi. This Strainer Cover Gasket - HWSP1600-S works with the Hayward Strainer Cover - SPX1600D.
Reply
will this fit on Sp2615X20?
Reply
I have a Hayward Super Self-priming pump 1hp which is an older model and I need a gasket for the pump lid. I believe the Model number is CASK27143B1. which gasket do I need so I can order it from you
Reply
This is the correct lid gasket for the Hayward Super Pump.
Reply
I have a hayward super pump model sp2602vsp, I need a gasket for the see thru lid. I tried a spx1600s gasket but that seems a little to big, wont fit in channel right. Is this the right one? thanks
Reply
Hi Ronald, yes for the model Hayward Super Pump sp2602vsp pool pump this would be the correct lid gasket.
Reply
I have a Hayward SP-1608 x 10 super pump. Will this super pump lid gasket fit the 1608 x 10 model?
Thanks
Reply
Yes, the gasket part number SPX1600S is the correct lid o-ring for the Hayward Super Pump SP1600 & SP2600 Series.
Reply
Is this the right gasket for the Hayward super pump 1 hp model #C48k2n143b?
Reply
Hello Maureen. Yes, this is the correct pump lid gasket for the Hayward Super Pump. If you are looking for additional seals and gaskets, the GOKIT3 contains a Motor Shaft Seal, Diffuser Gasket, Pump Lid o-ring, Housing Gasket, and lubricant. Please see attached. Tune Up Kit Hayward Super Pump - GOKIT3
Reply
Is this lid gasket (o-177)(spx1600s) able to fit the super pump 2600zlg
Reply
Hello Deborah. The Super Pump lid gasket 0-177 SPX1600s is compatible with the Hayward Super Pump 2600 Series Pumps.
Reply
Will this fit a hayward sp2615x202s? This pump is barely a year old and it seems too new to need a gasket already but water came out of it when the pump lost it's prime and I put the lid back on after priming. It has lost it's prime repeatedly in the last week.
Reply
Hi Deborah, this will fit your Hayward Super Pump SP1600 Series pump. Be sure to put a little lubricant on the gasket to help it seal. And check out our article on How to test for suction side air leaks if your pump continues to lose its prime. The motor shaft seal can become damaged if the pump runs without water in it, so that could be a leak source as well.
Reply
sp2615x202s is the model number. Wouldn't this be a 2600 model? I don't want to order the wrong part. Thanks.
-(SPX1600S).jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-(SPX1600S).jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Hayward Super Pump Strainer Lid Cover Gasket O-177 - SPX1600S")
The gasket/O-Rings and pump seal interchange for the SP1600 and SP2600 Series. Click to view the parts page https://www.inyopools.com/pool_parts_pumps_hayward_super_pump.aspx If the seal plate, motor mounting plate, impeller, or diffuser are for the SP1600 series the Drive Train Upgrade kit would be required as those parts are different. You are okay to place the order for the model sp2615x202s
Reply
Wouldn't this model number be a 2600 series instead of 1600? sp2615x202s
Reply
Disney this a 2600 series? I want to make sure I get the correct gasket.
Does listed gasket O-177 fit strainer lid cover on Hayward Model SP-2607x10 ?
Pump was purchased approx 1998.
Thanks
Reply
Hello John, yes this lid gasket is compatible with your Hayward Super Pump model SP2607x10. I have also emailed you an estimate that you can convert to an order if you would like. Item is currently in stock and ready to ship.
Reply
My Hayward Super Pump needs a new gasket and its model number is C48J2N131B1…..is this gasket the correct one?
Reply
