What are the dimensions of PR266AEP?
Reply
The raypak PR266AEP is 23"W, 28" L, 38" H. The electrical connections are at 32-11/16", the gas connnection is at 13-1/4", and the water connections are at 26-5/8".
Reply
How quick could this be delivered to Lakeville MN?
Reply
Steve- The Raypak Heater 266000 BTU LP ELE 009225 will ship Via truckline which take about 5-7 business days to arrive. There is no way for this to be expedited.
Reply
What is the average life span of a RayPack 266000 Btu Ele Unit with proper care and maintenance?
Reply
There's a lot of variables, but I've seen people that have had their RayPak heaters from 10-20 years so there's a lot of different variables. I'm not able to say that it's going to last you a specific amount of years.
Reply
does this heater have the nickel - brass heat ex. ? If not which one does?
Reply
Hi, Kurt. This unit has a copper heat exchanger, the unit with the cupro-nickel heat exchanger is PR266AEPX - 014951.
Reply
Will this Raypac 266 BTU heater work off a 100 lb. cylinder? I have six full ones right now and hope I can use them on this heater.
Reply
I do not know what you are talking about when you say if it will work off a 100-pound cylinder. Please elaborate a little more.
Reply
Does this unit come with water hook ups on the left or right side when facing it. This is the unit I have, buy my water connections are on the left side and this model looks like it on the right sidr, same side as the electrcal hookups.
Reply
Facing the control read out, the water connections are on the right side of the unit.
Reply
Will this heater work with a salt water pool ?
My model # shows P-M266A-EP-X
Reply
Hi, Don. Since you have a saltwater pool and based on the model of your existing unit I would recommend the Raypak Heater 266,000 BTU's LP ELE W/ Cupro-Nickel - 014951.
Reply
I'm looking to purchase the Raypak Digital Propane Gas Pool Heater 266k BTU | Electronic Ignition my above ground pool is currently chlorine and possibly switching to Salt in a year or two. Should I be getting the other unit that is nickel inside and will it be fine if im running chlorine for the time being and if I didn't switch?
Reply
Hi, Dennis. I would recommend getting the Raypak Heater 266000 BTU NG EE (cupro-nickel) - 014939 unit which is can be used with chlorine and or a salt water chlorine generator.
Reply
I'm looking to purchase the Raypak Digital Propane Gas Pool Heater 266k BTU | Electronic Ignition my above ground pool is currently chlorine and possibly switching to Salt in a year or two. Should I be getting the other unit that is nickel inside and will it be fine if im running chlorine for the time being and if I didn't switch?
Also what if I need the water output to be when looking at the control panel to the LEFT SIDE?
Reply
Hi, Dennis. I would recommend getting the Raypak Heater 266000 BTU NG EE (cupro-nickel) - 014939 unit which is okay to use with chlorine for the time being. The water connection can be switch by an authorized installer.
Reply
I just sent you a email Im looking to purchase a Raypak 009225 Propane heater with Water inlets on the left side
I need to know delivery date to 19020
Thanks
Rich
Reply
Hi, Rich. These unit are manufactured with the water connections on the right side. An authorized installer can switch the water connection to the left side during the installation of the unit. Delivery can take 5-6 business days.
Reply
I have a 21' round I'm converting to salt system, would this be the correct size heater. Our Hayward heater took a long time to heat the pool. We utilize propane. Thank you,
Reply
this heater is going to be intalled at a height of 900 meters above sea level I want to know if it is the one indicated for that height
Reply
Good day, that unit would be maxed at 2,000 feet. You would need to go with the Universal H-Series Low NOx Heater 250K BTU - LP - H250FDP.
Reply
will this heater work for a 14000gal inground pool @ 4400 Feet?
Reply
Hi. This heat can heat a 14000 gallon pool, however, will not operate at 4400 feet. You will need Part # 009233 which is rated at 3000-5000 feet.
Reply
I a. Looking to buy a propane pool heater for a small 18 ft round 4 ft deep above ground pool. What would you recommend ?
Reply
Hi, Polly. You can use a 100K BTU or higher heater depending on how fast you want the pool heater and the desired temperature.
Reply
What size heater do you recommend for an in ground containing 24,000 gal. of water? I am looking at the 266AEP model, would that be sufficient?
Reply
Hi. Heaters are sized using the pool's surface area, not the volume. If you can get me the surface area of your pool I can confirm what size heater will be best.
Reply
I need to replace a 250.000 BTU propane pool heater. Can the inlet/outlet be moved to the left side of the unit? Is this factory handled?
Reply
Hi, Juan. You are able to reverse the heat exchanger which is only done in the field. Instructions are available in the Raypak Owners/Instructions Manual page 25.
Reply
I have a 14 X 30 in ground sport pool which is 5 feet in the middle and then slopes up at the ends. Will a Ray PAC 266 BTU propane heater efficiently heat this pool. Also what size propane tank would you advise having installed.
Reply
Hi, Bill. Yes, this size heater will be sufficient to heat your size pool. The size tank will be based on how often the unit will run. It will use approximately 2.6 gallons of propane an hour.
Reply
possibly looking to replace our existing heater model PR266AEPC S/N 0611180780, would this be a direct replacement
Reply
Want to give customer two options 1) replacing unit 2) replacing heat exchanger and pilot assembly
M/N C-R266A-EP-X ASME
S/N 1607426977
Reply
Hi, Bob. The replacement unit is P/N 010211/C-R266A-EP-X-ASME - RP2100 266A LP IID ASME. As for the Complete Heat Exchanger - 010361F, Tune Bundle - 010369F and Pilot Assembly - 002003F are all compatible with that model and serial number.
Reply
Is this heater a millivolt system?
Reply
Hi, Rod. This unit is electric, the P-R266A-MP is the millivolt version.
Reply
how is the electric hooked up
Reply
Hi. The electrical info can be found on pages 26-27 of the Raypak Owners/Instructions Manual.
Reply
Does the unit come with the outdoor hood
Reply
Hi, Michael. The Top - 010335 is included with this unit which is not shown in the product images.
Reply
After the heater runs for a while it goes to #2 fault. What is this and how do we prevent this
Reply
Hello Len- The Fault you are getting sounds like it's the High Limit 2 Fault. This means one of your high limit switches on the heat exchanger is going bad. Raypak states an erratic high limit is often characteristic of an internal heat exchanger problem, e.g. scale build-up, defective bypass. You may need to call a tech for them to be able to identify exactly which one is bad.
Reply
How many BTUs and is this model ideal for an in ground 20,000 vinyl pool?
Reply
Hi, Julie B. This unit input BTU is 266,000 and is ideal for an in-ground that is 20,000 based on your desired temperature increase per hour.
Reply
Are there any fast shipping options? If I order 6/25/20?
Reply
Hi Jenny, unfortunately, heaters do not have any other expedited shipping options. The average delivery timeline is approximately 3-6 business days for these units.
Reply
Hi, forgot to ask...is it true that Raypak will not offer support or warranty unless heater is installed by a Raypak certified specialist? If so, where are you supposed to fine one when located on the northeast coast?
Reply
Hello Nikki, with Raypak there is a 90-day warranty if you do a self-install. If you have a licensed gas and or plumber do the install then there would be a full warranty. After install be sure to register the product on their website. If you were to need service you can contact them through their warranty portal and Raypak will reach out to a center in your area.
Reply
How big of a pool heater do we need to heat a 16,000 gallon inground pool in South Louisiana?
Hello Kearn, to heat a large pool we would recommend the RP2100 Digital Heater - R406A - Cupro-Nickel - Propane - P-R406A-EP-X #58. Here is a guide for Sizing Your Pool Heater.
Reply
Need to remove pin as it was entered inadvertently and I don't know what it is.
Reply
To access the program screen, press the Mode button until the display reads OFF. Remove the four screws holding the control cover on. Swing control panel down so the back side of the board is visible (see page 30). Locate the Program Mode button as shown in the figure on pg. 32. Press the program button (5-7 seconds) until SETdef appears on the
Reply
