Is this pump available with 2" plumbing ports?
Reply
The Hayward Super Pump does not come with 2" plumbing ports, however the Hayward Super II Pump here does have 2" plumbing ports >http://www.inyopools.com/Products/02201157001155.htm
Reply
How many hours per day should I run my pump?
Reply
There are many factors to consider; bather load, gallons of water, pump horsepower, type and size of filter just to name a few. A good guideline is 8-10 hours a day. On the cooler days and early and late season, you can cut the run time down to 4-6 hours because there is usually less swimmers and cooler water requires less chemicals. In peak season, when it is the hottest, raising the run time to 10-12 hours per day will help to keep the pool clean and circulating during it’s time of heaviest use.
Reply
Hi, can this pump be used with a salt water chlorinator [generator] made in South Africa by Justchlor which requires a salt level of 6000ppm by weight, yes I know most USA systems call for 3500ppm. After 27 months my pump motor bearing is whining badly and I presume the shaft seal has gone, I see Hayward has a kit with a salt shaft seal, do you stock this pump "salt ready" if this is what I need?
Reply
The SP2610X15 is a 1.5HP 230/115v single speed pump that can be used with salt water pools. The main issue with a higher salt ppm level is that the salt will corrode the rubber seals and any metals that it comes in contact with at a quicker rate. Unfortunately the pump does not come "salt ready". You would have to purchase a salt water tune up kit separately. I recommend changing the shaft seal every season with a salt water pool to prevent shaft seal failure.
Reply
The water pressure seems to be week as it exits into the pool. Does the motor lose efficiency over time or maybe the empeler needs to be replaced.
Reply
Motors will run full speed until the day they freeze up and stop. The most likely culprit is the filter. Trying this : if you have a sand or DE filter - put the multiport on re-circulate. If you have a cartridge, remove the element from the tank. Then turn the system on. If this returns the system to its usual power , you know you have to clean, or get new filter media. If that does not help, there could also be debris wrapped around the impeller. You can try to reach it by removing the basket and putting your hand in, or you have to separate the motor from the housing to really get at it.
Reply
My present model is SP2610X15 with a I I/2 HP motor. The PVC is I I/2 ". Can I use a 1 HP motor and if so what is the model number ? Can the complete unit come with salt water seals?
Reply
Neal, You can go down in horsepower to the UST1102 A.O. Smith 1 HP Round Flange Up Rate Motor, but you would also need to replace your impleller with a sp2607-c (spx2607c) part number 5110-10ca.The pump itself will not come with a saltwater seal, so if you decide to reaplce the motor I would suggest getting the salt water tune-up kit GOKIT3SALTSaltwater Tune Up Kit Hayward Super Pump.
Reply
I am using a superpump as a jet pupil for a 700 gallon in ground hour tub. It is feeding six jets and is approximately 75 feet from body of water. I only have descent flow from two of the jets a and very little from the other four. What is the possibility that this pump is not powerful enough to provide pressure to all six jets?
Reply
Hi Dan, Giving the distance the pump is from the body of water this pump would not provide the water flow needed to properly operate the jets on your hot tub. You will need a high performance pump like the Hayward Super II Pump or Tri-Star Pump.
Reply
Can you buy the Haward Super Pump housing without the motor? I need the pump without the motor.
Reply
The Hayward Super Pump has many parts available. If you are in reference to the Housing Strainer there is a 1.5" and a 2" option. The 1 1/2" Housing, Strainer Super Pump is PART# 5110-07A and the Housing, 2" Strainer, Super Pump is PART# 5110-07B. Please click here to view all parts available for the Hayward Super Pump.
Reply
Hi , I life in Curacao. here we have the powernet with 50Hz, can you provide a Hayward Super Pomp 1,5 HP in 50Hz version?
thank you in advance.
Regards Anthonius.
Reply
Hi Anthonius, The "SP2610X1551" is the 50Hz 220 volt model.
Reply
My Hayward Super Pump 1 1/2 HP is now extremely LOUD and seems like air is in the lines. What is the potential problem. Is the noise the bearings ?
Reply
Hi Robert, The noise could be the bearing or could be because you have a suction leak cause the pump to draw air into the lines. You will have to first resolve the air leak issue, we have a How To: Identify and Correct Air Leaks guide.
Reply
I need a Hayward 1.5 HP single speed super pump with 2 inch ports.
Do you have this unit ?
Reply
Hello John, We do not retail a 1.5HP Super Pump with 2" connections. You can purchase a Housing with a 2" ports, Super Pump is PART# 5110-07B. Please click here to view all parts available for the Hayward Super Pump.
Reply
my strainer housing has a leak model number hayward 2610X15. can I just buy the strainer housing
Reply
Depending on the size of the plumbing, you can purchase just the pump Housing, 1 1/2" Strainer Super Pump (spx1600aa) or the Housing, 2" Strainer, Super Pump (spx1620aa). Please not that the housing is just the housing and does not include any additional parts like o-rings or locking knobs.
Reply
Hayward Super pump. The motor on pump is getting hot, I don't think it will last long. I don't need the basket, just the motor?, the gold part? Where can I find that? thank,
Reply
Hello Bill, Here is a link to the Hayward Super Pump Parts page. This page lists all the parts, including motors available for the Super Pump.
Reply
My in ground pool of 30,000 gallons currently uses a Hayward C48L2N134B3 Series SE02 pump. Can I replace it with the Super pump SP2610X15 you offer with the strainer housing? If so what is improved over my old pump and what size is the pvc from the pool to the pump as well as from the strainer basket to the filter? What other options are available and what are the advantages of each over what I have now?
Reply
The Super Pump would be a great replacement pump as far as the pump you have now and the SP2610X15 both being 1.5HP. As far as telling you the differences between the two, I would need to know which model of Hayward pump you have, not the motor.
Reply
what is the rated throughput (cubic meter per second or gallon per second of model # SP2610X1551?
Reply
The gallons per minute (GPM) for this pump is based on the Total Resistance to Flow (Feet of Head). Here is a link to How Do I Calculate Feet of Head for My Pool? if you need assistance determining that number. The product page for the Hayward Super Pump 1.5 HP 50 Cycle 220V - SP2610X1551 has a chart to help determine the GPM of this pump.
Reply
I'm so sorry, I'm taking over this pool and I am trying to learn everything about it. The motor has gone out, and my neighbor has a similar pool so he is trying to help me to get it up and running again. The pump model number is SP2610X15. Thank you!
Reply
I have a Centurion b129 (01-64304-24) motor on a hayward super pump (sp2610x15). I am fairly certain the bearings are going due to high pitch whine from the motor, and I think I have a bad seal due to a leak at the area where the motor connects. Can you suggest
a. the proper replacement seal kit
b. replacement motor
c. what dual speed motor would work with my setup
THANKS
Reply
Hi, Seth. The Century Motor B129 and Tune Up Kit GOKIT3 or GOKIT3SALT are the parts needed. You can use the B2977T as a dual speed option.
Reply
changing to 110 volt hookup. can you show a schematic?
Reply
Here is our how to wire a pool pump guide. Also please be advised that on the motor label itself there is a small wiring diagram.
Reply
What is the right size pump for a Hayward 244T sand filter? The design pressure or flow in 66GPM. My current pump @ 1.5 HP is greater than that.
Reply
Hi. In order to confirm if this pump will be a good match for your filter you will need to follow the steps in our How To Size a Pool Pump Guide.
Reply
My existing pump has a barring going bad. The pump has a model number of C48L2N134B1 SER#18210CH. Further down on the manufacturer's tag is a number I am seeing on your list of pumps. That number is SP160Z1M. What I see on your list is SP2610X15. Is the SP2610X15 the correct replacement for the pump I have?
Reply
Joe, The information provided is for the motor. We will need to know the model number on the pump housing.
Reply
I have a Hayward 1 HP super pump. If I go to a 1.5 HP would I have to change any of the plumbing?
Reply
Hi, Nick. You can use your existing plumbing connections. The ports are in the same location. You will have to make sure that your circulation and filtration system is sufficient for a 1.5 Hp pump. Use our How to Size a Pool Pump and How To Size a Pool Filter to determine sizing.
Reply
I have a Hayward super pump exactly as pictured in your model SP2610X15 with the gold colored pump. Mine is model # C48L2N134B1 ( 1 1/2hp) and says SP-1610-Z1-M. made by A.O.SMITH. I need a replacement motor and seal kit but from what i see the replacement motor you recommend is a Century (C48L2N134), MODEL UST1152. Can you tell me why can't you buy the exact same replacement motor as the original (gold) or does that only come with the complete pump. I'd like to stick with hayward equipment.
Reply
Hello, the original motor on your pump is currently a Hayward branded Century Motor. The only difference between the UST1152 and your current motor is the gold colouring. If you wish to have another gold Hayward branded century motor, you will need to purchase a whole new pump.
Reply
I have the gold 1.5 HP, Hayward Super Pump, SP 1610 21 M , C48L2N134B1, 115/230, SF 1.0, FR 56J, 1.10 KW, cont. duty, code H, PH 1, 60 hz, 3450 rpm, I need to replace with a high efficiency pump. Can I use the SP3015EEAZ or the SP2602VSP? Thanks.
Reply
I need to replace my Start compaitor but i'm not sure which one I should buy. I have model SP2610X15, •115/230-Volt at 60 Hz. which one do I need?
Reply
OK!! My motor finally went on my inground pool. And yes the Hayward motor/pump is now going on 22 years!!
Looks like the shaft is corroded, hard to get to so prob best now if I replace it. Pump is also on 22 years plus.
Model number is C48L2N134B1 - 1 1/2 HP, 3450 RPM. I am going to replace the whole motor/pump at this point since I do not want issue later on and now need just a pump. What model do you recommend?
Reply
Hi Ed, I would suggest the PureLine Prime PL2602 1.5 HP which is a drop in replacement for the Hayward Super Pump, the only difference is the Prime has 2" ports where the Hayward Super Pump has 1.5" ports.
Reply
how to clean & change sand in Hayward S-240 filter
Reply
Here is a great article on how to do so.http://www.inyopools.com/HowToPage/how_to_change_sand_in_a_sand_filter.aspx
Reply
I currently have a C48L2N134B1 1.5 HP Super pump which I need to replace. I've decided to replace the whole pump because replacing just the motor seemed to complicated for me. The SP2610X15 looks identical and I'm hoping not to have to configure my current set up. Is this the right replacement for me? Thanks
Reply
What is the replacement motor for this pump?
Reply
The Hayward Super Pump SP2610X15 replacement motor is the 1.5 HP Round Flange 56J Up Rate Motor - UST1152
Reply
Hello I've just purchase a Hayward Super pompe. I want to install the wires on the pump... on which screw do i put the black and white wire?
What happens if i put the wrong color wire on the wrong screw?
Nore, there's only two screws.
Reply
On the top of the pump you will see a decal that has a wiring diagram. You can use this picture to see how to wire the pump depending on if you are using 110 or 220
Reply
Thanks for the answer, however not quite clear on the diagram on which screw the black wire goes on. My model is C48L2N134B3, Serial 02217CH. Volt 115/230, HP 1 1/2, RPM 3450. As you can see in the picture it's set to 230 volts and i've placed the black wire on top and the white wire at the bottom... Is this the correct wiring configuration for 230 volts ?
If it's 230v, it doesn't make a difference since both lines are 115v hot. As long as you have 1 wire to line 1 and the other to line 2 and green to ground, it will be fine.
Reply
We currently have a hayward super pump 1.5 hp that the motor went on. We previously had the same hayward super pump with 1hp. I'm trying to figure out if we need to be at a 1hp or 1.5 to replace ours. Our pool is roughly 20,000 gallons. I will attach photos of my pump. Any advice would be greatly appreciated.
Hi, Samantha. Unfortunately, we're unable to tell using pictures. You can use our How Do I Calculate Feet of Head for My Pool? or our How to Size a Pool Pump guide to assist you with properly sizing a pool pump.
Reply
what is the reply to this inquiry?
Reply
The pool that is 20K gallons will need a pump to turn over at least 42 gallons per minute in hours to turn the total gallons over one time. The Hayward Super Pump 1 1/2 HP Single Speed - W3SP2610X15 is the better choice for this particular application. We offer How to Size a Pool Pump for Your In-Ground Pool that will help provide more details to pump sizing and choice of types of pumps needed, remember every pool is different, it is not only the gallons per minute that factors the specific pump to order. Please see Which is Best: High Head or Medium Head Pumps?
Reply
I was just going to order a replacement motor for my model C48L2N134B1 Hayward Century Self Priming motor, which looked like it was your model UST1152, but when we followed your how to video to disassemble the motor from the pump, we cracked the pump because it was too tightly fastened to the motor. Now I think that I need to replace both pump & motor.The pump that I have is Model SP2610X15.
Hi Michelle, If you wanted to replace your entire pump then this would be the proper replacement and might be the way to go. We also carry the Waterway 1.5 HP SMF Pump which is a drop-in replacement for the Hayward Super Pump by using the supplied adjustable bases and will save you a little bit of money over the Hayward. The Waterway Pump does have 2" Ports where the Hayward has 1.5" ports so you will need to pick up a two of these 2" x 1.5" reducer bushings
Reply
I have a Hayward 2610X15 pump w/ pump serial number 600021 operating summers since ca. 1995. Bearing squeal is intermittent. If I were to buy a replacement 2610X15, could I unbolt its motor and pump guts from its pump housing by removing the 4 exposed bolts and swap it for the existing motor/diffuser/impeller/etc assembly? If the dimensions allow this to work, is there any history of internal pump erosion that would require replacing the existing pump housing to achieve full performance?
Reply
We do not recommend doing that as it will void the manufacturer's defect warranty on the Hayward Super Pump 1 1/2 HP Single Speed - W3SP2610X15 If you want to replace the motor and those parts, we recommend ordering the Century 1.5 HP Round Flange 56J Up Rate Motor - UST1152 Generic Super Pump™ Style Drive Train Upgrade Kit 1.5 HP - 5110-53 All pumps have a lifetime of 10-years, once they have surpassed the ten-years the whole pump should be replaced or the motor with the upgrade kit. *Note, if the housing is 25-years old, it may be best to replace the whole pump as the housing could weather and pin-hole leaks could come about.
Reply
Hi i have a igp 32x16. Would this match up with the Raypack 6450 heat pump? Is the gmp on this filter ok for that heat pump? Thanks
Reply
We will need more information. Please refer to our How to Size a Pool Pump for Your In-Ground Pool http://www.inyopools.com/HowToPage/how_to_size_a_pool_pump_for_your_in_ground_pool_.aspx
Reply
Does pump come with cord?
Is it easy to install power cord?
Reply
No this does not come with a cord. You can use this 115V Pool Pump Standard 3 Prong Power Cord Please note if you a wiring the pump 230V then this cord would not work.
Reply
Why on the Hayward site is this model number shown as the superpump II? And this model is shown as SP2610X15?
Reply
Hi Robert, this pump is the same as the SP2610X15 on Hayward's site. The extra "W3" just represents the online retail part number.
Reply
Need a motor replacement for this Hayward super pump. Guess this one is an older model with 4 knobs holding the sight glass, no visible ID's.
Hi Pete, the correct replacement single speed motor for the motor included in your photo is the B229SE. You will also need a Hayward Super Pump seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I have a hayward super pump 1.5 hp model c48L2n1314B1 that is making a high pitch sound. Probably the bearing going out. what pump would replace it?
Reply
Hi Kim, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
current hayward pump & 24 in pro series sand filter system came with a 1.5 hp super pump. sys approx 9 yrs old. no model no# on pump moter model - C48L2N134 need 15hp hayward replacement moter
Reply
Hi Mark, the single speed replacement motor for your Hayward Super Pump motor model C48L2N134 is the UST1152. It is also recommended to replace the seals when replacing a motor. For a chlorine swimming pool, it will be the GOKIT3 and for a saltwater pool, it will be the GOKIT3SALT.
Reply
I have a Hayward super pump Model C48L2N134B1 and the motor went out. What would be the replacement or what pump would work if I wanted a new one?
Reply
The W3SP2610X15 would be the correct complete pump. The replacement motor would be model UST1152.
Reply
is this super pump suitable for outdoor exposed to rain and direct sunlight service?
Reply
Hello. The Hayward Pool Products Super Pump is designed as an outdoor pool pump and as such is exposed to the weather. Protecting the motor from direct sunlight and/or direct exposure to water (rainfall or irrigation) can increase its life span. A protective pool motor cover can provide such protection. Protective Pool Motor Cover - R221016 Other recommendations: maintain good airflow around the pool pump - keep the air cooling ports free of debris. make sure the pump installation site has sufficient water drainage to prevent water from building around the motor. clean the pump basket and pool filter per the manufacturer's recommendation.
Reply
