$188.93
Part # PL2855
Warranty 2 Year
PureLine 2 HP Replacement Pool Motor for Pentair® & Jandy® brand pool pumps
Is your pool pump motor running loud, leaking or humming? These are all signs that it’s time to be replaced. The PL2853 PureLine Replacement motor is designed as a drop-in replacement motor for some of the most popular 2 HP pool pumps like the Pentair® Whisperflo, Pentair® Challenger, Pentair® Super Flo, Jandy® Stealth and many more.
The PureLine replacement motor is made of the highest quality components like sealed ball bearings which means it is an ultra quiet motor. Because of its high-quality construction the PureLine replacement motor is backed by a full 2-year warranty.
When it comes to replacing your motor Inyo has you covered we have created a ton of resources to make this project a snap, like our Video on How to Replace a Pool Motor this video walks you through all the steps to replace your motor. Most of our customers decide to tackle this project on their own and by following our video they complete this project in about an hour.
When replacing your motor we highly recommend a tune up kit which includes all the seals and gaskets for your pump. Many times when you use your old seals you may have leaking and seal leakage is one item which will void the motors warranty so make sure to protect your investment with a tune up kit. Below we have listed the tune up kits for some of the most popular pool pumps.
Don't Forget Your Tune Up Kit
Pentair® Whisperflo Tune Up Kit
Pentair® Challenger Tune Up Kit
Pentair® Superflo Tune Up Kit
Note: NOT California Title 20 Compliant.
California Title 20 Compliant Options:
Disclaimer:
All manufacturers’ names, brand names, trademarks, images, symbols, descriptions, and part numbers are used herein for reference purposes only.
I have a Pentair 340038 that has a 1HP motor 196238 mated to it. my system is only running at 10 psi and I would like to increase it to clean my pool more effectively. will this 2HP pump fit?
Reply
Hi, Matthew. A filtration system running at 10 PSI is okay. In order to increase the pump's water flow, you will have to make sure your system is larger enough to handle the water flow and change the motor, impeller, and diffuser of the pump to all match along with the pump seals. All parts are listed on the Pentair SuperFlo Pump Parts Diagram.
Reply
I'm looking for the replacement motor for my WF-23 whisperflo pump - 2 hp. Motor 7-177476-28. Will this fit?
Reply
Hi, Bob. Yes, this PL2855 motor will replace P/N 7-177476-28. You will also need the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
I am trying to find a replacement motor for our pool waterfall pump. I am not finding anything that is a direct replacement. Could you recommend a replacement motor?
56y and 48y square flange frames are interchangeable.1/2" wider body diameter but identical hole spacing.
will this 2hp motor replace a century ao smith 2hp hayward spx2715z1me threaded shaft. usq 1202 is recommend 48y replacement
Reply
Hi, Monty. Yes, this PL2855 motor can be used as a replacement. The USQ1202 and or the SPX2715Z1ME are options that can be used.
Reply
thanks, cleaned old motor, put new capacitors,go-kit with seals, etc. bench test motor not installed in pump housing yet.after installation will test all equip and plumbing if ok will run all for test period. now know usq 1202 1252 etc and pl2855 are ok century purline ao smith and several others are same osr similar made under different names for new owners of ao smith century
Reply
Less than 1 hr
Screwdriver, Pliers, Socket Set, Adjustable Wrench
1 0
Took pictures of my pump housing and sent to inyopools to identify proper motor model for pump housing. Received motor. Had questions about wiring and called Inyopools customer service and they walked me through proper wiring. Viewed DIY Video on Inyo site on replacing this motor. Was lot easier than I thought. Definitely would do it again.
2 to 4 hrs
Screwdriver, Pliers, Socket Set, Wrench Set, Adjustable Wrench
1 0
Purchased 2 of these 2HP motors, each dedicated, one for spa spillway, and the other for the waterfall. This Sunday my pool technician opened the pool, and asked him to installed these new motors on my existing Waterway SVL56 pumps, one was dead and I decided to replace both.
After he got them installed with new shaft seals and replaced pump o-rings, one of the two motors started running hot right off the get go, while the other was fine. My pool technician who has 30+ years of experience rechecked the wire and pump internals on that one, found nothing wrong and motor was running very hot and after 20-30 minutes it would shut itself off and be extremely hot.
With pump intervals confirmed to be fine, I looked at the power feed and breaker. Read the voltages, 124.6V out of each leg and combined 247v from the wire ends connecting to the pump while running and also when wires were but connected. Read the same voltage at the breaker and the amp reading matched the label as well.
Basically tried everything one could try and at the end have no doubt one if the motors is defective. Took it apart again, took pictures of the motor mouth with impeller out to upload along with pictures of the labels, required by INYO pools to start the warranty replacement process. Hope they can rush the replacement motor to me in time for the weekend. Wish this wasn’t the case, cause the other motor is running perfectly and these are quiet pumps in general.
The Most Recent Reviews
(5 out of 5 stars) GREAT PRODUCT AND OUT STANDING SERVICE
Reviewed By: Inyo Customer ()
GREAT PRODUCT AND OUT STANDING SERVICE.
Was this review helpful to you?