By Hayward Pool Products


Details

Top

Part # HP50TA

Alternate Part #'s HAY-15-5050, HAYHP50TA

Product Description

Extend your pool season with a Hayward® HeatPro® heat pump.  Quiet and economical, heat pumps use the outside air and a titanium heat exchanger to generate heat for a fraction of the cost of gas.  Save up to 80% on operating costs.

Features:

  • Titanium Heat Exchanger - excellent salt water and chemical corrosion resistance
  • Exclusive 'Ultra Gold' evaporator coil corrosion resistant especially in coastal areas
  • Quiet operation - quiet backyard environment
  • AHRI certified performance - independent lab certified performance ensures the value of the purchase
  • 2in x 2 1/2in CPVC union plumbing connections - common union for installation or service, adapts to larger plumbing recommended for greater efficiencies
  • Light weight - less than 250 lbs.

Warranty:

  • 2 Year Warranty on manufacturer defects
  • 5 Year Warranty on Compressor
  • 10 Year Warranty on Titanium Tube

 

* PLEASE BE ADVISED THAT THIS UNIT IS NOT BE SOLD IN THE STATE OF FLORIDA *

Product Specifications

BTU:
50,000 BTU
Pool Size:
Up to 13,000 gal.
Coefficient of Performance:
5.4
Volts:
240
Hz:
60 Hz
Phase:
Single
Recommended Breaker Size:
30
Min Flow Rate:
30 GPM
Max Flow Rate:
75 GPM
Dimensions:
31.25" dia x 40" h
Weight:
120 lbs.
Refrigerant:
R410A
Watts:
3280 W
Compressor Size:
3.25 HP
Heat Exchanger:
Titanium
Max Water Temp:
104 °F
Compressor:
Scroll
Manufacturer:
Hayward
Heater Type:
Heat Pump
Top

?     Asked on 1/4/2013by Guest

Can this Hayward heat pump run on 115/120 volt?
 Reply

A  Answered on 1/4/2013 by InyoPools Product Specialist Patrick P.

Unfortunately no. The HP50TA runs on 220/240V and requires a 30 amp breaker.
 Reply


?     Asked on 10/8/2013by Guest

If I have a large pool pump will I need to have a flow meter for the heat pump?
 Reply

A  Answered on 10/8/2013 by InyoPools Product Specialist Patrick P.

According to Hayward their heat pumps have a flow rate range of 30 to 70 GPM, with an optimum flow rate of 45 GPM. If your pump is capable of significantly more flow than this, a flow meter is recommended to insure the flow rate is within the prescribed range.
 Reply


?     Asked on 10/8/2013by Guest

Can a heat pump be installed indoors?
 Reply

A  Answered on 10/8/2013 by InyoPools Product Specialist Patrick P.

Generally no. Heat Pumps work by transferring heat from the surrounding air to the pool water. If a heat pump is installed indoors there must be a continuous supply of warm air from which the heat pump can extract heat. If you must heat the air in the room before the heat pump can extract that heat to heat the pool, there would be no benefit to the heat pump.
 Reply


?     Asked on 10/8/2013by Guest

Can a heat pump be installed under a deck?
 Reply

A  Answered on 10/8/2013 by InyoPools Product Specialist Patrick P.

No. Any installation that causes the air being discharged from the top of the heat pump to be recirculated back into the heat pump will cause a loss of capacity and efficiency in the heat pump. Installation of a heat pump under a deck, or a low over hang will allow the air being discharged to be drawn back in by the heat pump.
 Reply


?     Asked on 10/8/2013by Guest

Is the refrigerant in Hayward heat pumps environmentally safe?
 Reply

A  Answered on 10/8/2013 by InyoPools Product Specialist Patrick P.

Yes. Hayward uses R-410A refrigerant in all their heat pumps.
 Reply


Top

Review Summary

 (Average 4.82  out of 5 stars)
16 Rating
5 star:
 
(13)
4 star:
 
(3)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Recent Reviews