Will this board fit correctly into the Aqua-rite enclosure? There is a review of the product that says that it doesn't fit right.
Reply
Hi. This PureLine Display Board PL7101 will fit the Aqua-Rite controller.
Reply
Had AGUA COLLECTION FROM GOLDLINE CONTROL PANEL NEW INSTALLED 2003. THE SERIAL # 5A0111-001953. DO YOU HAVE A REPLACEMENT ?
Reply
Hi Bob, You would require this AfterMarket AquaRite Main PCB Board PL7100
Reply
I need a replacement for my Aqua Rite, Goldline control display PN: 132604 Rev: F.
I have a 33k pool built in 2005. My old display doesn't show indicators for, Power, Generating, Super Chlorinate, anything. Off switch will not shut off diagnostic display.
This is why I believe I need the above. Can you help me figure out what replacement part is best?
Reply
Hi Chris, This would be the proper display board but the majority of the time we see that the PL7100 Main AquaRite PCB Board is the problem.
Reply
I replaced my main circuit board a couple of months ago and all worked fine after that. Now I am not getting any lights or display. The fuse has been changed . Does this seem to indicate a bad display board?
Reply
Remove and/or reseat DSP board. Pins may be shorted together or not making contact with connector. If pins are good, if voltage is less than 5VDC on pins 2 & 4, replace main board: (GLX-PCB-RITE)
Reply
how much for board and flo switch for a aquarite clorine gen.
Reply
Mike, You can view the parts and pricing on the AquaRite parts page.
Reply
I have an Aqua Rite T-15 system installed in Sept. 2003. I stopped using it about 6 years ago and replaced the cell with a chlorine feeder because the cell was going out about every 1 1/2 years. I want to return to the salt system. Do I need to update both circuit panels to accommodate the new cells? My software has a 1.10 reading.
Reply
My chlorine generating light briefly comes on and then goes off. Does not produce chlorine. I had the cell checked and it is functioning. Does this need a display board replacement?
Reply
Hi. The issue is with the Main PCB. To get your system up an running again you will need to replace the Main PCB - GLXPCBRITE.
Reply
I have a 2005 aqua rite system, will this replace the pn 132604 display board. I need new fasteners to attach it to the main board. Do you have those, Thank You.
Reply
Hi, Stan. This Aftermarket AquaRite Display Board is compatible with a 2005 System. The Display Standoff - GLX-STDOFFPAK20 is available, however, we do not carry them.
Reply
Is this Part a direct replacement for an Aqua Rite Goldline using a T 3 Cell with firmwarwe verison 1.5
Reply
No, the OEM GLX-PCB-DSP display board is what is recommended for your model salt system
Reply
I have a new AQ Rite 5 - x288 box with a g1-066604k-1 display board. T cell 15 attached. Control board does not allow me to specify a particular t cell. Will your board allow me to specify t cell? I am getting high salt reading sometimes shutting generation off. Voltage and current are correct for t 15 when it does generate. Cell is also new and clean. Thanks
Reply
Every morning when my pool pump starts my Aquarite system displays the average salt level at 700 to 1900, and no chlorine is generated. The check salt light blinks. The Instant salt level is 3200. I re-calibrate the system to match the instant salt level and then the system starts chlorinating. This works until the pump shuts off at the end of the day. The next morning I have to repeat the process. Do I need a new main PCB? My cell has been tested and works fine.
Reply
Hi, Phil. Replacing the Main PCB - GLX-PCB-RITE will resolve your issue with having to keep recalibrating the system.
Reply
My Aqua Rite generating system was not generating, and salt level is reading 2.50, check salt level (red) and inspect cell (yellow) are on. Replaced generating cell and now it is generating, but salt level and inspect cell lights are still on. The main PCB is Goldline Controls PN: 066012B-1 Rev. B, and the display board is Goldline Controls PN: 132604 Rev. F. What probably needs replaced?
Reply
Hi, Bob. First, test the salt level of your pool to make sure it's 2700-3200 ppm. If the salt level is within range, press and hold the Diagnostic button for 3-5 seconds. If neither of these worked, you will need to replace the Aqua Rite Main PCB - GLXPCBRITE.
Reply
My display is stuck on one value (appears to be cell current) and will not change. When this started last year a few wiggles of the button would get it working (changing display values) but, after a few seconds, it still defaulted back to the cell current and not the PPM. Would this problem be the DSP board? I might add that when I manipulated the button and got it changing the values were in the correct range. The generating light is on and all appears OK operationally..
Reply
Hi, Deborah. That issue that you're having is a Main PCB - GLXPCBRITE issue, not the Display.
Reply
How do I determine which is bad, the digital display ,or the mother board ?
Reply
Hi, Rich. You can use the AquaRite Troubleshooting Guide to diagnose which board will need to be replaced.
Reply
Aqua-Rite 5A0403-1035650 SYSTEM WITH A DIPLAY BOARD GOLDLINE CONTROLS PN: 132604 REV:F I NEED A NEW DISPLAY BOARD IS THIS THE ONE I CAN USE OR CAN YOU TELL ME WHAT ONE I NEED TO BUY? I CANT SEE THE SETTING IN THE WINDOW ANYMORE.. THANK YOU
Reply
Hi, Jim. You can use this aftermarket Aqua Rite Replacement Display PCB Board - PL7101 or the OEM Board - GLX-PCB-DSP.
Reply
I enclosed a picture of my Gold Line part number 132604. The display on the board no longer gives the status. If I move the control switch up and down sometimes the display will flash on and off. I see that you sell a replacement board for this unit. Is it compatible to the one in the photo and do you think it will fix the issue.
Thanks for your response
Hi, Ernie. Yes, this PureLine AquaRite Replacement Display PCB Board - PL7101 will work as a replacement.
Reply
Ernie, I have the same display as you had that is not working. Did you purchase the pl 7101 and did it fit and work properly. Thank you in advance
Reply
Ernie, Did the new main board fix your problem. I have a aqua rite and I purchased the same board but I keep getting an error check salt and cell. I did and both are working correctly. Are there more that one replacement boards and did I get the wrong one?
Reply
have agoldline display board part no 10-066604g-1 , the numbers are faded sometimes their unreadable,also cannot calibrate the salt level. continually reads between 3.0 to 5. when trying to calibrate can`t hear a click in the panel when switching from auto to off back to auto. system is working fine but the numbers for salt level don`t show it
Reply
Hi, Jim. Replacing the Display Board will resolve the dimness. It appears that the unit is displaying in metric mode. Use our How to Change the Units of Measurement on an Aqua Rite SCG guide to switch it to standard.
Reply
my display is showing artifact which is unreadable, In the salt % display. Looking at your product measurements on hole spacing. the 2 3/4 spacing is correct from top to bottom but side to side is 5 5/8 which does not make sense. My measurement is 2 3/4. is a type O on your end?? Or the wrong display.
Reply
Hi Carl, We did double check our dimensions and you are correct they are listed inaccurately. The 5-5/8" dimension is a typo and that should read 2-3/4"
Reply
I purchased my Aqua Rite system in 2007. The main board part number is 066012C-1 rev C. The display board part number is G1-066604F-1. The firmware is 1.4. Will this replacement board work in my system?
Reply
Yes, the PureLine AquaRite Replacement Display PCB Board (GLX-PCB-DSP) - PL7101 would replace your existing display board.
Reply
I installed the new main board on my AquaRite but have no lights or digital display. Is there a way to test the PCB board to check if it is bad. Prior to installing the new main board I would get a reading for the flow light and digital display of numbers but was not getting any of the other lights for power, generating, etc.
I also received a spare fuse with the new board but there were two black "electrical clips" in the bag. I was not sure what these were for. Thank.
Reply
Terry, it does not sound like you have the jumpers installed on the board. Those are crucial for supplying power. Please send us a photo of the way you have the board wired to upload@inyopools.com.
Reply
the display on my aqua rite reads 'hot' and will not change. is the display panel bad or the control board bad?
Reply
The LCD display will read HOT when the water temperature is above 140F. If the cell is 3 years or older then we highly recommend having it tested at select pool retailers that have the Aquarite cell tester for the cell may be failing.
Reply
The display on my aqua rite Goldline reads HI. The salt level in the pool is good. The cell is good. Could this be a problem with the display board or main board?
Reply
Hi, Robert. Try powering down the system, and unplugging the cell.
Reply
Will this fit my Hayward Aqua Rite T 9 Cell control panel
Reply
Hello Thomas. The PureLine AquaRite Replacement Display PCB Board (GLX-PCB-DSP) - PL7101 is compatible with the Hayward AquaRite T-Cell 9 Models.
Reply
Can I use the replacement pureline display board PL7101 with the existing aquarite main board GLX-PCB-RITE
Reply
Hello Robert. The PureLine Replacement Display PCB Board, Compatible with AquaRite™ GLX-PCB-DSP - PL7101 is guaranteed to be compatible with the Hayward AquaRite Main Board (GLX-PCB-Rite) for any AquaRite T-Cell 15 or T-Cell-9 System. The recommendation for the T-Cell-5 and T-Cell-3 Systems is the Hayward Aquarite Goldline Display Board - GLX-PCB-DSP
Reply
