Is my display # G1-066604F1 compatible with the new main board # GLXPCBRITE, or do I have to order a new display # 2807-11 ( GLX-PCB-DSP ) ??
Also is Turbo Cell T cell 3 compatible with board # GLXPCBRITE ?
Reply
Yes your Display will work with the new board as well as the cell. New board will allow you to choose what cell type you have.
Reply
My display board is a 2008 model with P/N G1-066604G-1. Will this board work as a replacement for mine ?
Reply
Hi Howard, The Aqua Rite Display PCB (GLX-PCB-DSP) will be the correct part if you have the AquaRite, SwimPure or AquaTrol Control Panel's. I was not able to cross reference p/n G1-066604G-1 to any specific part.
Reply
My display board is GOLDLINE CONTROLS PN: 066604F-1. Will board GLX-PCB-DSP work as a replacement?
Reply
Hi, The Aqua Rite PCB Display Board will be the correct replacement for the Goldline Salt Generator.
Reply
My salt pool isn't generating salt. The display is working but it won't turn off. No other lights are working on the display. Should I replace the display & circuit board. System is @ 7 years old.
Reply
Hi Lauri, I would start with the Aqua Rite Main PCB (GLX-PCB-RITE). With the PCB replaced if the lights are still not coming on then replace the Aqua Rite Display PCB.
Reply
My power light is on continuously but no other lights are on. The cell is clean. I went through the trouble shooting procedures in the manual and all voltages and ohms were correct and it said to change this board. Would the indication of only the power light on be a likely symptom?
Reply
Yes, it sounds like the display board is going bad.
Reply
I have a Goldline Aqua-Rite T-15 system that is more then 10 years old. My display is showing 9900 for salt and only the power light is on. There is no light, clicking or any sound associated with the cell generator turning on when cycled to auto or super clorinate. Is this a main board problem or display board problem?
Reply
Bob, this sounds like the main board, I would suggest the After Market PL7100 AquaRite Main PCB Board
Reply
My Aquarite T-15 is controlled by a Aqualink RS8. The actual PPM is not matching what the display is showing on my RS8 even after calibration. My Aquarite is only showing 2100PPM so I get a constant 'Check Cell' message. I've recalibrated the Aquarite by removing the four remote wires on that connect my Aqaurite to the RS8, and then recalibrating. I'm only able to get the read out to show correctly for about a week or so, then it drops back down to 2100. Is this my display or main PCB?
Reply
Hi. I would recommend getting the water tested, if your salt level is about 500 ppm above what the controller is reading then you will need to add salt to your pool.
Reply
how do I know if this part is bad?unit makes chlorine ,but te percentage changes daily. set at20 ,drops to 7 or goes up to 30%
Reply
Mike, The display typically does not affect the readings. You can use this troubleshooting guide to diagnose the issue.
Reply
My display show’s numbers, my power and generating lights come on and off. I do hear clicking when they do come on.
Help... Thanks
Reply
Hi, Rocco. Based on what you've described, the Main PCB is the issue. You can either replace it with the OEM - GLXPCBRITE or Aftermarket - PL7100 Main PCB if compatible.
Reply
The display window on my Goldline Aqua Rite unit is half dark now and thus unreadable. Could that be a problem with PCB or do you think that it is just the display?
Reply
Hi, Charles. It sounds like it's just the display because it's not completely blank. You can use the Step H on page 11 of the AquaRite Troubleshooting Guide to be sure.
Reply
i have a hayward salt water generator t9 every thing is working correctly but have no generator light or super chlorinator is this the display panel
Reply
Hi, Gerald Cox. The issue could be the Main PCB - GLX-PCB-RITE. In order to confirm, you will have test the Display Board. Instructions are available on Page 11, Step H of the AquaRite Troubleshooting Guide.
Reply
Is the part 132604 the same as GLX-PCB-DSP? My display board doesn't have the gold tabs on the bottom left. Is this replacement set to a T-15 by default? Thank you
Reply
The first number you mentioned is our product code for the part. The second code you mentioned is the manufacturer's code. Therefore, these two codes both reference the same part that is in question. This board doesn't get set to anything by default, it is based on your system. So when you receive this, you'll have to set it to your board.
Reply
If I read it correctly, I have a Gold Line P/N Q1-066012F-1 REV A. What is the replacement?
Reply
Hi, Fred. In order to locate the correct replacement board, we will need to know the controller name. For example, AquaRite, AquaLogic, etc.
Reply
Did you receive my earlier reply? It is an Aqua Rite by Gold Line.
Reply
AQUA RITE, GOLDLINE CONTROLS, 12X24 Pool,
Reply
Is this piece a replacement for the gold line controls pn: 132604 rev F?
Hi, Bern. Yes, Display PCB (OEM) - GLX-PCB-DSP is the correct replacement.
Reply
I have a Goldline Aqua-Rite T15 system over 12 years old. My display shows 0.00 and I can step through the display.
AL reading is AL-5 but I can not change it to AL=0. Slide switch has no effect. I have only the power on LED illuminated.
All voltages are present and correct.
What is your diagnosis?
Reply
Hi, George. The AL reading is unable to be changed. If the cell amps which is the 3rd reading is zeros, the issue is the cell.
Reply
Is the 2009 version of this part a direct replacement for the 2008 version?
Reply
Hi, Donald. This Display PCB - GLX-PCB-DSP will work with version prior to 2008 and current.
Reply
Hello, is this part compatible with 132604 REV: E
Thanks
Reply
Yes, the AquaRite Display PCB (OEM) - GLX-PCB-DSP is compatible with 132604 REV: E
Reply
Hi, board seems to be running as there is vibration within the unit, but the display is not lighting up. Would a neww display be needed or a whole new board?
Reply
Hi Darlene, 9 times out of 10 we find that both the Display board and Main AquaRite PCB Board will need to be replaced.
Reply
How often is it simply a matter of a blown resistor?
-GLX-PCB-DSP.png?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-GLX-PCB-DSP.png?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Hayward Aquarite Goldline Display Board - GLX-PCB-DSP")
Sometimes it is a bad resistor normally one of the legs on the resistors will be broken so I would visually inspect your resistor. If you do replace the resistor you have to solder it on so it is a little bit more of a professional repair. We also find that in most cases when soldering a new resistor the repair will last 1-2 years and then any future repairs last shorter, so eventually a new board will be required.
Reply
I just replaced this part and my salt level is reading a bit higher than before. Is this normal?
Reply
I actually just did this on Monday and had the same issue. My issue was I was adding salt before because I was getting a low salt reading on a bad cell / board. So when I replaced the board and the cell I had a higher salt reading due to the fact that it was now reading off the new correct board and cell instead of a bad cell / board, and had too much salt in my pool.
Reply
My Aqua Rite Goldline model G1-066604F-1 display board is completely blank and no longer produces chlorine. Can i buy a new display or do i have to buy the "Main board" as well
Reply
Thank you for contacting Inyo Pools, Have you tried checking the fuse in the box?
Reply
Is your product a replacement for my 2009 Goldline Controls P/N: G1-066604K-1?
-GLX-PCB-DSP-4b17b40a-172c-4275-a1fc-dbea0f3b02e2.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-GLX-PCB-DSP-4b17b40a-172c-4275-a1fc-dbea0f3b02e2.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Hayward Aquarite Goldline Display Board - GLX-PCB-DSP")
Hello. The AquaRite Display PCB (OEM) GLX-PCB-DSP is the Hayward OEM replacement Display Board for part number Goldline Controls G1-066604K-1
Reply
My Aqu-Rite Generator display P/N G1-066604F-1 just went bad on me what is the correct replacement part number.
-GLX-PCB-DSP-eab98e05-32b9-43b0-86e7-288bbae872f6.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-GLX-PCB-DSP-eab98e05-32b9-43b0-86e7-288bbae872f6.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Hayward Aquarite Goldline Display Board - GLX-PCB-DSP")
Hello Carlos. The AquaRite Display PCB (OEM) GLX-PCB-DSP is the correct replacement display board for the Hayward AquaRite display P/N G1-066604F-1.
Reply
-GLX-PCB-DSP.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-GLX-PCB-DSP-fdbb4009-1347-41b6-9e47-8a10ae9bfa31.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-GLX-PCB-DSP.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Hayward Aquarite Goldline Display Board - GLX-PCB-DSP")
-GLX-PCB-DSP-fdbb4009-1347-41b6-9e47-8a10ae9bfa31.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Hayward Aquarite Goldline Display Board - GLX-PCB-DSP")