THE TABS BROKE OFF AND ARE STILL IN THE HOLES. I'M UNABLE TO REMOVE THEM. HOW CAN THE REPLACEMENT BE INSTALLED?
Reply
Hi Juan, The only option you have is to use the Hayward/Seablue Weir.
Reply
My pool is missing the weir therefor I can't measure it. Is there another way to find out what model number skimmer I have? I'm pretty sure it's a Hayward because there is an "H" under the cover.
Reply
Hi, typically on the underside of the skimmer lid there is a model number that identifies the entire skimmer. From there we can locate the correct weir gate part. The "H" would denote you have a Hayward skimmer.
Reply
Hi, I wondered if you carry just the piece of hard foam that fits into Hayward skimmer part sp1082k4. I don't need to replace the whole piece, just the foam. Thanks!
Reply
Hi Julie, I'm sorry we do not carry just the foam, only the foam and the weir.
Reply
Hello, I have two Hayward Weirs and both are warped, is there a better replacement for them other than just the factory ones?
Reply
Hi, Kevin. The CMP Weir - 25141-360-000 can be used as a replacement.
Reply
I need a new skimmer "Trap door" Hayward part number SP 1082K in white. Do you have such a part? One of the tabs on the door broke off.
Thank you,
Richard G.
Reply
This will be the correct weir door for your model.
Reply
Hello. I have to replace the weir (door) on my skimmer. It's a Hayward SP1082K4 in white. Do you carry this item?
Thank you.
Reply
Hi, Robert. This Skimmer Weir - SPX1082K is the current replacement.
Reply
we have a really old haywood skimmer must be at least 30 years old unfortunately door flap just broken we have made a temporary repair but hoping the SPX 10821K spare part will fit.
Our door flap had the number 80 171 (probably too old to find registered anywhere!) on the back and measured 7 3/4 ins wide x 5 3/4 tall..more concerned whether the lugs would fit?.....Pool always been well maintained but we are looking for a quick replacement part repair .
Thankyou
Avril
Reply
I need to replace just the sponge on the door? Do you sale just that? I f so what is the part number?
Reply
Hi. Unfortunately, the foam is not available as a separate part for this weir. You will have to purchase the complete Weir.
Reply
I need to replace my weir door, pretty sure it is Hayward but unknown part number. Opening approximately 7 1/2" width and height 6". There are 2 bolts approximately 5" apart. Attached photos - any suggestions? Thank-you!
Hi Richard, Could see if you can pull any part numbers off of the skimmer lid or skimmer basket? The part numbers should be embossed into the plastic you can simply reply back to this email with that information.
Reply
This persons description and picture match mine. Mine is a Hayward SP 1070 B. 7 1/2” long by 6” tall. What will fit it? The compression weirs I’ve tried, all cone off when the kids get the water rocking.
Reply
The numbers on the weir door are 51-6222. It is a Pentair but the skimmer lid reads Paddock, the name of the pool builder.There is no model number but says the flow rating is 10-55 GPM
Reply
Hello, The part number you will need based on the part number 51-6222 ishttp://www.inyopools.com/Products/07501352028751.htm?Keywords=51-6222
Reply
The number on my flap for my skimmer box says SP-1082-K will the SPX-1082-K fit my skimmer?
Thank you
Reply
Hi Barbara, Yes the SP-1082-K and the SPX-1082-K are the same thing and work interchangeably.
Reply
