My inground pool was installed with a 120V Amerlite standard incandescent light fixture. After ~ 3 years water started seeping into the fixture, so I replaced the bulb and got a new gasket. The one I got was the white-colored OEM gasket. It has since been leaking even more than before. I've lubricated it, made sure everything was snug and re-inserted it to no avail. Do I need a new light fixture, or did I just get the wrong gasket for this light? (there's also a standard black-colored gasket). H
Reply
I personally would try another gasket and would suggest the Extra Heavy Duty Guardian Gasket for the Pentair Amerilite If this does not work then the next step would be to replace the entire fixture with a new Complete Pentair Amerlite Fixture If you did end up going with the new fixture then you would have an extra Gasket which may not be a bad thing as these do need to be replaced periodically.
Reply
Does this gasket work with the fixture that takes the NA704 replacement bulb?
Reply
This gasket only works for the Pentair Amerilite and Sam light models but the bulb is used on multiple models. The specific light model would be needed to cross reference the correct gasket needed.
Reply
Can't read the type all I see is it's American Product. Will this gasket fit?
Reply
Can you send us a photo with a measuring tape in the photo, showing the width of the light and the depth of the light.
Reply
Hello,I am looking for lens gasket for American products co.k996044, will this gasket work? Also pentair seems to be compatible with American products,are they the same company?thanks for your time,Alan
Reply
Good morning Alan, Yes Pentair bought American products and that gasket will work for you.Pentair Lens Gasket Amerlite & SAM Light (791016)
Reply
Hi, I need a gasket for a 12 volts spa light that is about 20 years old with the inscription "WADE DESIGN" on the glass.
The glass lens diameter is 3 3/4".
The original gasket is grey and has these dimensions:
*outside diameter is in between 3 3/4" and 3 7/8"
* inside diameter is about 3 3/8"
* measured difference between outside and inside diameter is 1/4"
* thickness is about 3/8"
I read somewhere that Gasket Lens Spx0590G Opt 3553-03 gasket might fit, but want to make sure.
Reply
It might fit but to be sure I need to know the model of your light fixture. If you can attach a picture of your light fixture so I can identify it, I will be able to find the correct lens gasket.
Reply
My existing light fixture is 120v 250 w since I am replacing gasket and bulb would be possible to change LED instead if yes what do I have to do
Thanks
Reply
Hello, You would have to make sure what type of light you have, the ones that you can switch over is if you have Hayward Astrolite SP058 Series, Pentair Amerlite 784 Series, Note: Not compatible with Swimquip Light Fixtures or Hayward SP0540 series.
Reply
I have an inground installed in 1999, the light is an Aqua Lumin II. In the direction book it calls for a lens gasket with a part # of 788802 is this still available ? DO you stockit? Thanks for the info.
Reply
Will this gasket fit my light. The model # is R 400BCL. Also I need a light bulb for the same fixture. The fixture indicates it is rated for a 400W bulb,120V. The fixture says bulb type: R-40. Pease tell me what bulb is designed for this fixture. Thank you.
Reply
Jim, The model number you provided does not show in my system. Can you please attach a photo of the label on your light fixture?
Reply
Hi, the existing fixture is a Purex No E.905830... also says Model PLH-100-5 and Model PLH - 100-3. on the original mfg decal... Just trying to confirm which replacement gasket will work here.. thanks
Reply
Hi, Mark. You will need the Lens Gasket - SPX540Z2. for the Poolstar PLH Series light fixture.
Reply
Hello, could not get much info on this but this is what I got off the bulb housing:
7885xx 7845xx 7895XX
500 watt 120 volts bulb type R-40
Will this gasket fit my pool light housing / lens ?
Reply
Yes the Pentair Lens Gasket Amerlite & SAM Light (791016) would be the replacement gasket for your light housing.
Reply
Hi, i have the larger 8" fixture in pool. It appears this will work. What about the smaller 4" ish gasket for the spa? do you have a PN for that? Thx
Reply
So if we base your question off of the Amerlite series pool light model then that would potentially reference the Spabrite/Aqualight spa light series. That gasket would be listed as key number 3 on the parts diagram that you can view here to confirm that this is indeed your spa light. If you cannot verify that then we would advise to look for the model label on the cone of the light or take a few pictures of it and email those to upload@inyopools.com so we can identify it.
Reply
disassemble an aqua-lumina2 light to change the bulb.
Reply
Hi. Instructions are available in the AquaLumin II - Nicheless Light Operating Procedures Manual pages 14-15.
Reply
need a gasket for a pool light fixture. dont know the model number. it is 25 years old. . the existing gasket is grey and is smaller , about 6.5 inch in dia. what should i buy??
Reply
Hi, Raj. Please provide pictures of your fixture so that we can try to identify and locate the correct gasket your fixture.
Reply
I have ordered a Pentair Lens Gasket Amerlite & SAM Light (791016) . What screw do I need to order to fasten the gasket to the lens?
Reply
Good day, there is not a screw that would fasten the gasket to the lens. There is only a screw that would attach the light housing to the niche, which would be 3525-03.
Reply
I took my fixture apart because it had leaked a little over the winter. Cleaned it up and reassembling. Gasket looks good. Would a little 100% silicone caulking help around the lens and gasket?
Reply
We would not recommend using any silicone on these lens gaskets as that is not manufacture assembled that way.
Reply
I have an American products pilot light 7892xx, 7842xx
300 Watts, 120 volts, bulb R-40
Is this the correct gasket?
Or can you provide the correct gasket P/N or Model number.
Looking for gasket to fit this model. Manufactured in 1993. Gasket measured 7 1/2 inches
You have the Pac Fab Hatteras light which uses gasket part number 57-110-1272.
Reply
Looking for help in a lense gasket
The gasket for your light is part number 57-110-1272.
Reply
7.5" glass lens. Gasket looks loose and about 8" diameter. Can you please recommend a proper gasket?
Hi, Mike. You have a Hatteras Pool Light Fixture, the Lens Gasket Hatteras - 614516 is the correct replacement.
Reply
I have an older model light cover, made by american products co , with #3915 embedded in the glass. The final dimensions of the gasket "on the lens' is 8-3/4 inches outside diameter, 7-5/8 inches inside diameter with 1/2 inch on each side, and 3/4 inches front to back. which gasket should I order? The bulb is 300 watts, 120 volts, screw in. Please recommend the bulb , gasket, and type lubricant or sealer to use.... Thanks
Reply
Hi, Richard. This is the correct lens gasket based on the info provided.
Reply
Hi,
My pool light shorted out last year. I think water got inside. I'm looking for a replacement bulb and gasket or the pictured fixture. Thank-you.
-O-170-68e2e991-7745-41c1-9c80-0ac78fac5423.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-O-170-68e2e991-7745-41c1-9c80-0ac78fac5423.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Pentair Amerlite Pool Light Gasket 8-3/8\" - 79101600 - O-170")
Unfortunately, I cannot use any information on this label, it all regards UL listings and dates approved. Please provide an image of the front of the fixture showing the lens with a tape measure across the lens and faceplate. We will also require the voltage and watts needed for the bulb. Please test the fixture to verify it did not short out the entire fixture before ordering the bulb and gasket.
Reply
Looking for proper gasket replacement and bulb.
Hi Anthony, Thank you for the photos! You will require this Hayward Pool Light Lens Gasket and this 120V 500W Replacement Pool Bulb
Reply
Can't find a name on my light but the lens is 7 1/2 inches wide. Need a gasket
Danny
Reply
Hello, we would just need to know the specific pool light model to confirm for you. The model should be located on the rear of the fixture on a label. If not legible, could you send us a few photos? One of the entire light fixture, the lens itself, and the dimensions of it? To supply photos simply click the reply link below and upload your photos or quickest on using our live online chat feature. Once we get those photos we can make the proper recommendation.
Reply
I need to replace the gasket and would like to replace the bulb with and LED light. Can you please reccomend both to buy ?
Thanks
Hi Edwin, Thanks for the photos! You will need this Amerlite Lens Gasket and this 120V Pool LED Bulb Color Changing
Reply
Hello, would this gasket fit? thank you.
Hi Lee, yes this is the correct lens gasket for your series pool light. Based on the label of your light you have the Pentair Amerlite light series.
Reply
i can seem to find any infor on my pool light but I need a new gasket pool store says it measures about 7.5 inches.
Hi Howard, could you send us a few photos of the front of this ring and the glass lens? To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
Hi, need help to identify proper replacement lens gasket. Label on housing unit totally corroded by algae. Used in an American Products niche that says use with BC-300, BC-400, or BC 500. But the OD and interior diameters of the gasket for those models seem larger than mine (est. 7 3/4 OD and 6 7/8 int diameters). Hopefully, the attached photos will help. Might it be a hatteras or hayward light instead of American Products? It was installed in 1991. thanks much.
Hi Gene, yes you do have the Pac Fab Hatteras pool light and the gasket is part number 57-110-1272.
Reply
Would like to replace bulb with led and gasket. Please advise which bulb and gasket are appropriate. Thank you.
Hi Quen, this would be the correct lens gasket and you would also need the J & J Colorsplash LED light bulb. Here is a guide that we put together for upgrading your pool light to an LED color light changing one that also may assist.
Reply
lens gasket 79-101-600-0-170 . this gasket has a smooth side and the other side has two ribs. Which side of the gasket face is place on the light cone. Smooth or ribbed
Reply
Hi Mark, the smooth side of the lens gasket is to be on the outside exposed and the ribs are to be wrapped around the outside of the lens itself. The lens rim essentially is fitted inside of the gasket.
Reply
Please help me identify the correct gasket, pics attached.
I am showing that this is a Pac-Fab / Pentair Amerlite. Here is a link to the gasket that fits that light...Lens Gasket - 79101600 - O-170
Reply
What gasket is used for the fixture in the photo please?
Hello Larry. The Lens Gasket 79101600 is the compatible lens gasket for the Pentair Products Amerlite Pool Light Fixture as shown in the attached photo.
Reply
I have a model 784XXXXX, 788XXXXXX, 789XXXXXX Pentair pool light. Which gasket fits please?
Reply
Hi Matt, yes, the Lens Gasket - 79101600 - O-170 is perfect for your Pentair Amerilite. Be sure to put some lubricant on the gasket to help keep it sealed for a long time when you replace it.
Reply
What's the difference between this part for $14.99 and part no. 79101600 for $53.xx? Both have 8 3/8" spec.
Reply
Hello Vijay, the version gasket that is $14.99 is a generic manufacturer and not fabricated by Pentair. The more expensive version is an original Pentair product.
Reply
Need gasket for American products series 7884XX underwater fixture. Measures 8.5 inches across on outside of ring. Measures 7.5 inches across inside ring. Height is1.63 inches. Which of your brand fits?
The Pentair Amerlite Pool Light Gasket 8-3/8" - 79101600 - O-170 should be perfect for your Pentair Amerlite Pool Light. Be sure to put some lubricant on the sealing surfaces to help it stay sealed for a long time, and review our guide on How to Replace a Pool Light Gasket for some helpful tips!
Reply
-O-170.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-O-170-8f010bd2-dcca-414b-88c8-9012ea59b336.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-O-170.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Pentair Amerlite Pool Light Gasket 8-3/8\" - 79101600 - O-170")
-O-170-8f010bd2-dcca-414b-88c8-9012ea59b336.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Pentair Amerlite Pool Light Gasket 8-3/8\" - 79101600 - O-170")
-O-170.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-O-170.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Pentair Amerlite Pool Light Gasket 8-3/8\" - 79101600 - O-170")
