I have a pool that is about 10,000 gallons but I am thinking of buying a salt chlorine system for pools up to 20,000 gallons. Would the larger unit be a problem?
Reply
It is not a problem to oversize a salt system. It would take the larger unit less time to produce the necessary chlorine so it is actually more efficient. When the pool volume is very close to the capacity of the salt chlorine generator (for example, the pool is 18,000 gallons and the generator is rated at a maximum of 20,000 gallons), we would recommend going up to the next size generator.
Reply
Is the salt included with the salt chlorine generator?
Reply
No, salt is not included. You would purchase the salt locally and the quantity will depend upon the number of gallons of water in your pool. Use a salt that is at least 99.8% pure NaCl. The preferred salt is evaporated, granulated, food quality, and NON-iodized. Avoid using salt with anti-caking agents like sodium ferrocyanide, also known as yellow YPS (prussiate of soda). These cause some discoloration of fittings and pool surface finishes. DO NOT use calcium chloride.
Reply
Is it better to oversize or undersize the Hayward Aquarite?
Reply
It is better to oversize the Aquarite for two reasons. First, the salt cell will last longer because it does not have to run as long to generate the proper amount of chlorine. This will also lengthen the life of the cell. Second, if you under size the salt system you may have to add chlorine in the warmer months when the chlorine demand is higher.
Reply
Will the Aqua Rite work on a portable spa?
Reply
The Aqua Rite chlorinator is specifically designed for use with in-ground pools, and will not work with portable spas or hot tubs due to its high output.
Reply
What is “SUPER CHLORINATE”?
Reply
The unit will run in 2 separate polarities and continually switch sides as long as the pump continues to run. The desired output percentage dial will tell the chlorinator how long to generate in each polarity, SUPER CHLORINATE simply tells the unit to ignore the dial setting for 24 hours and generate chlorine at 100% of its capability.
Reply
Do I need to change anything else in my system to make my pool a salt pool using this AQUARITE40000?
Reply
No. The AQUARITE40000 is an add on to your current equipment. Of course assuming that you have sufficient flow to begin with but other than that with installing this will be all you need. Just add the appropriate amount of salt to the pool.
Reply
Is there any advantage in using the Hayward Aqua Rite system as opposed to the "generic" system?
Reply
The advantage to using a Hayward salt system versus a generic is that you would be owning a product that has been in the industry for many years gaining its reputation as a quality product. Not that a generic cannot be one but does not have the reputation and reviews gained over the years that Hayward does. Nonetheless, both items are designed to do generally the same thing.
Reply
I have a two speed pump - will the Aquarite work running my pump in both the high and low speeds?
Reply
Hello Keith - The Aquarite will work with a flow rate as low as 11gpm. As long as your pump meets that requirement you will not have an issue.
Reply
I have an Aquarite AQR15 that is less than 1 year old. I am getting a No Flow solid light on panel and my chlorine level was very low. 3 weeks ago everything was perfect. Is it under warranty and what coudl it be?
Reply
The no flow light could be from the filter either being old or dirty, or the flow switch being bad. Usually these models are warrantied for either 1 or 3 years. Just depends on the model. I advise you to try the filter troubleshooting first and then if the problem is not resolved touch base with Hayward at 1-866-772-2100 to diagnose with their tech support department. You can also get with a licensed pool contractor. Have the model and serial number of the unit ready if you speak with Hayward..
Reply
Firstly, my flow light flashes a good 25 minutes. Could it be the flow switch itself or perhaps or circuit board related ?
Salt and inspect cell light are steady lit! If I clean cell could that send a signal back to circuit board that problem is rectified? the unit is 3 years old!
Reply
Hello Simon attached is a Diagnostics Manual to help you go through the steps to find whether it is the board or flo switch
Reply
Hi, For the Aquarite system (35K gallon pool), my current plumbing is tight. I have 19" horizontal between the elbows and 24" vertical to the ground going back to the pool. Will everything fit? I have seen some yideos where they put the flow control on the vertical downstream of the cell. Is that ok?
Reply
Hi Jason. Yes, if I understand your setup correctly, you can install your Aqua Rite with the Cell in the 19" horizontal piping going to an elbow and down to the flow switch in the 24" vertical before the returns. Make sure you have at least 12" of straight pipe between the elbow and the flow switch.
Reply
How do I go from Celcius to Fareneight pool water temp to show up in the box on the wall??
Reply
1. Slide the Main Switch to the "Auto" position. 2. Push the Diagnostic button repeatedly until "ºF" appears on the display. 3. Slide the Main Switch from "Auto" to "Super Chlorinate" and back to "Auto". 4. Push the Diagnostic button to exit
Reply
How do I go from Celcius to Fareneight pool water temp to show up in the box on the wall?? I have an F-15 Aqua Rite Cell system.
Reply
1. Slide the Main Switch to the "Auto" position. 2. Push the Diagnostic button repeatedly until "ºF" appears on the display. 3. Slide the Main Switch from "Auto" to "Super Chlorinate" and back to "Auto". 4. Push the Diagnostic button to exit
Reply
IS the aquarite system setup for 110 volt. Or will I need to have 240 installed? I would also like to setup an automated system that I can control from my phone. Pool pump, valves, hot tub and heater. DO you offer something for this and the valve switches.
Thanks
Dylan
Reply
HI Dylan, This system can be wired for either 115 or 230 volts. We do have Pool Automation Controls with chlorine generator that you can control your system via your phone.
Reply
how long is the inline assembly? ie how much of a straight run do I need to remove to install?
Reply
Hi Henry, In order to install the TCell, you would need a total of 36" of straight run. You can see installation requirement in the AquaRite Owner's Manual.
Reply
my salt cell has fail the test and the local pool store. If I replace just the cell does the flow valve need to be replaced as well? Also the system is 10yrs old would recommend replacing the entire system? I do not know if the computer board is operating correctly.
Reply
Hello Julie, You would not need to replace the flow sensor unless you are getting a NO FLOW light on your control panel. We would recommend replacing the entire system only if your control panel and cell are not functioning, as that would be the most cost effective option.
Reply
I'm thinking of this as a DIT project. I'm pretty handy with plumbing, less so with electrical. Can this be installed by a novice/ first time installer? Would lack of professional installation void any warrantees?
Reply
The manufacturer recommends this salt system is installed by a pool care professional providing a bill of sale of work performed. I included a link to the Aquarite Goldline Owners Manual with warranty information. Should you have additional questions, feel free to contact Hayward at 1-908-355-7995.
Reply
Two questions:
1) Why doesn't the System come with a 120V three prong plug anymore?
2) Why doesn't the wiring diagram and supply connection terminals indicate which terminal(s) gets the black (HOT) and which gets the white (Neutral) wire ?? Is it because the system is ETL Certified (known for their questionable certifications) and not UL Listed ?? Or is it because it can be wired either way without damaging the board ?
The old boxes had markings and came with a normal cord and [;ug...
Reply
Hello, You might want to talk to Hayward tech support 800-657-2287 just to confirm with them on their wiring diagram they provided. Walking you through wiring process on live and neutral wiring.
Reply
my salt is reading 0 put in 30 bags 2 days ago. should i wait a little longer. Ran pumps but never turned on cell unit until today. Any way to calibrate the negative reading it is 0 also
Reply
Hi, Chuck. If you system is reading 0 ppm then something is wrong with the system. You can find troubleshoot and the recalibration steps in the AquaRite Troubleshooting Guide.
Reply
I have the Aquarite Goldline addition. The LCD display works and is showing 2500, none of the LED lights are lit. When I turn the unit on the red no flow light blinks which it always does until everything gets flowing, then it shuts off and the power led light comes on, then a couple seconds later all the LED lights go off but the LCD stays on still showing the value of 2500. Is this a symptom that the PCB is bad? Do you know the replacement for the PCB if this is the case?
Reply
Hi, Mike. It sounds like you have a bad PCB. You can use the OEM AquaRite PCB - GLXPCBRITE or Aftermarket AquaRite PCB - PL7100.
Reply
My Hayward circuit board no longer shows any of the indicators The only light is the "no flow" indicator for a few seconds when the the pump is turned on. If the circuit does not show indicators, does this affect the salt cell from generating? Is there a test to determine if the salt cell is generating?? Not sure if I need what I need, a new circuit board and salt cell or just one of them. I replaced the fuse on circuit board, still nothing.
Reply
Hi, Jackie. Chlorine generation is not happening. The issue is the Main PCB. You can use the AquaRite Troubleshooting Guide pages 31-36 to confirm.
Reply
When i first purchased the unit the salt content number would show up on the the display. Now I am getting things showing up that makes no sense at all. It is producing chlorine. I am trying to get the numbers to show up as normal again.
Any sugestions?
Reply
So it really depends on what sort of codes are coming up on your screen but take a look at our diagnosing/troubleshooting guide on an Aquarite and also this how to change the units of measure guide as well. One of these may very well be what you need to both diagnose and troubleshoot your salt generating system.
Reply
My system shows "Check Cell" even after cleaning the cell. There was a build-up of debris in the cells. This was installed this summer and has only run for about two months. There is chlorine being generated since I have tested the levels and can see it coming in from the jets. Any suggestions?
Reply
Hi, Tom. Press and Hold the Diagnostic Button for 3-5 seconds to reset the error lights.
Reply
I just bought the Crystal Pure 3.0 Salt system. my old salt system by Goldline has connections for my indoor control panel. I'm not seeing where to hook up on my new Crystal Pure system so it communicates to my indoor control panel. Did I buy the wrong unit?
Reply
Hi, Jeff. The Crystal Pure 3.0 System does not have the RS-485 connector.
Reply
I have a 30K gallons pool, which salt chlorine generator I would need to convert?
Reply
Hi. Miguel. You will need a 40K or 60K system in order to effectively sanitize your pool. You can select from our Salt Chlorine Generators.
Reply
Is this the T 15 system?
Reply
The Hayward AquaRite 40K does use the TCELL15 cell.
Reply
I have a Speck S90-III 1750 RPM single speed pump, 20,000 gallon in ground pool, and Tagelus TA-60D filter. Can I still use all these components with this Chlorine Generator?
Reply
Hi, Carlo. This system requires a minimum of 11GPM in order to operate. So if your pump is able to provide sufficient water flow, it will work.
Reply
Will our existing PH system from a Goldline AQR-PRO work on the AQR15 system?
Reply
The AQR15 is not made to control the Ph System from a AQR-PRO
Reply
Call 1-888 HAYWARD to be sure
Reply
The AQR15 is not made to control the Ph System from a AQR-PRO
Reply
I currently have a Hayward CL200 Chlorinator plumbed in my system. Will the cell be a direct replacement as far as the fit between the unions?
Reply
No, the salt cell is not a drop-in replacement for the CL200.
Reply
is this unit a complete system and will not need any other items ( can it be tied into a time clock for filter )
Reply
Hello Rich. The Hayward AquaRite Salt System, 40,000 Gal Pool, Control Panel & TurboCell - Model W3AQR15 is a complete system containing all the parts necessary for installation. Attached please find the AquaRite Owner's Manual. Please reference Section - Wiring - Input for Stand Alone Operation, page 11, for wiring instructions to a time clock. The installation of a check valve is recommended if the Salt System is installed in conjunction with a Heater/Heat Pump. The check valve should be installed after the heater/heat pump outlet and prior to the electrolytic cell.
Reply
