Product Description

Features:
• 120/240v Pump 1 circuit
• 240v P2 circuit (selected models)
• 120/240v blower (selected models)
• 120/240v ozone circuit
• 120/240v Circ Pump circuit (30GPM minimum)
• 1.4/5.5kW heater 
• 12v spa light circuit
• Patented M7 technology
• Plumb on pressure or vacuum side
• Component cords included
• Control panel included
• US & Canadian safety approvals

INYO# 9790-010BALBOA # 54218 BALBOA MODEL NUMBER IS VS 510S SPA CONTROL

*********************************************************************************************************************

THIS IS A BALBOA RETRO-FIT SPA CONTROL DESIGNED AS A COMPLETE REPLACEMENT CONTROL INCLUDES: (SEE BELOW FOR MORE DETAILED INFORMATION) CONTROL WITH HEATER SPASIDE CONTROL PANEL SPASIDE CONTROL PANEL ADAPTER PLATE SPASIDE CONTROL EXTRA LABEL AMP CORDS LIGHT HARNESS

*********************************************************************************************************************

SPECIAL NOTE - USING THE SYSTEM WITH A CIRCULATION PUMP IF THIS IS BEING USED WITH A CIRCULATION PUMP AND THE CIRCULATION PUMP IS USED TO RUN THE HEATER, THEN YOU MUST USE AN IRON MITE PUMP AS THE CIRCULATION PUMP. YOU MUST HAVE A LEAST 20 GPM THRU THE HEATER TO ACTIVATE IT AND THE IRON MITE SHOULD PROVIDE ENOUGH FLOW. DO NOT USE A SMALLER CIRCULATION PUMP TO RUN THE HEATER OR IT MAY NOT PROVIDE ENOUGH FLOW.

*********************************************************************************************************************

53600-HC CONTROL CONVERTIBLE 120 / 240 VOLTS M-7 STYLE SYSTEM, USES SENSORS INSTEAD OF PRESSURE SWITCH INCLUDES A 5.5 KW 240V / 1.4 KW 120V FLOW THRU HEATER RECEPTACLE FOR 2-SPEED PUMP 120 / 240 VOLTS RECEPTACLE FOR SINGLE SPEED PUMP 120 / 240 VOLTS RECEPTACLE FOR BLOWER 120 / 240 VOLTS RECEPTACLE FOR OZONATOR 120 / 240 VOLTS (MUST BE SAME VOLTAGE AS 2-SPEED PUMP) RECEPTACLE FOR SPA LIGHT 12 V - 1 AMP CONTROL BOX IS GRAY PLASTIC DIMENSIONS: HEIGHT: 10-1/2" WIDTH: 12-5/8" (BOX ONLY) 13-1/2" (INCLUDING GROUNDING TERMINAL ON THE SIDE) 13-7/8" (OUTSIDE OF THE BOTTOM MOUNTING FEET) DEPTH: 4-5/8" (BOX) 5" (FROM FRONT OF HEATER UNION NUT TO BACK OF CONTROL) HEATER 15" LONG FLOW THRU STYLE (MEASURED FROM FLANGE TO FLANGE) 2-1/4" DIAMETER TUBE UNION ENDS ARE 2" SLIP CENTERLINE OF THE HEATER IS 2-7/8" FROM THE BOTTOM OF THE FEET 10165 ADAPTER PLATE FOR SPASIDE CONTROL BLACK TEXTURED PLASTIC WITH PEEL OFF STICK ON GASKET ON THE BACK OUTSIDE DIMENSIONS ARE 8-1/2" X 3-1/2" INSIDE DIMENSIONS ARE 6-3/8" X 2-1/4" 53189 SERIAL STANDARD SPASIDE CONTROL OUSIDE DIMENSIONS ARE 7-3/8" X 3-1/4" USES AN 8 PIN PHONE PLUG TYPE CORD CORD IS 7 FT LONG BUTTONS: BLOWER, MODE, JETS 1, JETS 2, LIGHT, WARM, COOL 10402 EXTRA SPASIDE CONTROL LABEL USED IF THERE IS NO BLOWER TO CONTROL SAME BUTTONS AS THE STANDARD LABEL EXCEPT THERE IS NO BLOWER BUTTON AMP CORDS THESE ARE ALL 4 POSTION TYPE AMP CORDS, 5 FT LONG THERE IS 1 - 4 PIN CORD FOR A 2 SPEED PUMP THERE ARE 3 - 3 PIN CORDS FOR OTHER EQUIPMENT LIGHT STANDARD BALBOA LIGHT HARNESS, 10 FT LONG HARNESS INCLUDES HARNESS WITH PLUG IN TO MATCH BOX TWIST LOCK TYPE REFLECTOR AND 12 VOLT BULB THRU WALL FITTING IS NOT INCLUDED

Review Summary