Part # 4656-10A
Manufacturer Code 51013811
Dimensions 17" L x 4" W x 2" D
INYO # 4656-10A PENTAIR / AM PROD # 51013811 GENERAL DESCRIPTION: THIS IS THE COMPLETE MAIN SHAFT WITH SPACERS, HANDLE, AND TOP CAP GENERAL INFO: THIS IS USED ON AMERICAN PRODUCTS / PENTAIR 2" PUSH PULL VALVE MATERIAL: SHAFT: BLACK PLASTIC SPACERS: BLACK PLASTIC TOP CAP: BLACK PLASTIC (INCLUDED WITH THIS ASSEMBLY) HANDLE: BLACK PLASTIC (INCLUDED WITH THIS ASSEMBLY) MOST OF THIS ASSEMBLY IS A SINGLE MOLDED PIECE DIMENSIONS: LENGTH: 17" (A) (NOT INCLUDING HANDLE) SHAFT DIAMETER: 1/2" (B) SPACERS: TOTAL # 2 SPACERS INCLUDED DIAMETER: 2" THICKNESS: 1/2" FROM OUTSIDE TO OUTSIDE GROOVE: 7/32" SPACING: (MEASURED ON CENTERLINE FROM FIRST SPACER WITH THE FIRST SPACER AT ZERO) 1ST 0 2ND 8" SPACER O-RINGS: (2) INCLUDED THESE ARE STRETCHED ON TO THE SPACERS SO THE DIMENSIONS SHOWN ARE FOR THE ORIGINAL O-RINGS BEFORE THEY ARE STRETCHED OUTSIDE DIAMETER: 1-7/8" INSIDE DIAMETER: 1-1/2" HOLES IN SHAFT: (MEASURED ON CENTERLINE FROM THE HANDLE END OF THE SHAFT) HOLE: 1/8" AT 1-1/2" FROM END HOLE: 1/8" AT 7" FROM END ASSEMBLY INCLUDES: SHAFT WITH 2 SPACERS O-RING FOR EACH SPACER (2 TOTAL) HANDLE TOP CAP AND TOP NUT MARKINGS: "P/N 510130" IS MOLDED INTO THE TOP NUT
*******************************************************************************
TOP PLATE INFO INCLUDED? INCLUDED INYO # 4656-08A PENTAIR / AM PROD # 51012911 GENERAL DESCRIPTION: THIS IS THE TOP CAP ONLY USED ON THE AMERICAN PRODUCTS 2" PUSH PULL VALVE THIS DOES NOT INCLUDE THE TOP NUT MATERIAL: BLACK PLASTIC SHAPE: ROUND THIS IS HELD ON THE SHAFT WITH A PIN DIMENSIONS: OUTSIDE DIAMETER: 2" (A) TOTAL HEIGHT: 1-3/4" (B) CENTER HOLE DIAMETER: 1/2" INCLUDES: TOP PLATE ONLY MARKINGS: THERE ARE NO MARKINGS ON THIS
*******************************************************************************
HANDLE INFO INCLUDED? INCLUDED INYO # 4656-01 PENTAIR / AM PROD # 51011800 GENERAL DESCRIPTION: THIS IS THE HANDLE USED IN THE AMERICAN PRODUCTS 2" PUSH PULL VALVE MATERIAL: BLACK PLASTIC SHAPE: T-STYLE THERE IS 1 HOLE IN THE BODY OF THE HANDLE DIMENSIONS: LENGTH: 4-1/2" (A) WIDTH: 1" HEIGHT: 1-1/2" (B) INCLUDES: HANDLE ONLY MARKINGS: THERE ARE NO MARKINGS ON THIS
*******************************************************************************
ANTHONY POOL 1983 INGROUND "DE" IS THIS CORRECT ??
Reply
This page is the one for an Anthony Push Pull Valve. If it is an Anthony, it will be brass. If it is plastic, it may be the one you found. Please look to see if there are any other part numbers on any of the parts you have. We can match up the correct valve from there.
Reply
I have an American Product filter, my backwash valve (push pull) has broken and needs to be replace. It has an 8" center to center bulk head fitting. What else do I need to know to get the right replacement part?
Reply
Hello, Tom. You may either replace the entire valve or replace the Piston Shaft Kit. Click here to view the link for the parts diagram and the complete valve. I have included two other links you may find helpful as well. How To Replace the Hayward Slide Valve Handle and Piston Assembly and How To Replace the Hayward Slide Valve Internal Shaft O-Ring. I do not have one specific to Pentair, you may use these as a guide.
Reply
I think that the measurement of 2" top to bottom is wrong. I am trying to ID this valve. I only need the interior part. Thanks. Rich
Could you send us a few photos of the filter tank to include the label on the filter tank with your model information? To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
Filter my guess is over 30 years old.
Thanks for the photos Rich! The KDI filter is the same as this American Products Titan Stainless Steel Filter. A new version from your valve was created and you will need this Pentair Push Pull Valve, unfortunately, the internals for your old valve are no longer available and you would need to purchase the complete Pentair Push Pull Valve.
Reply
The Most Helpful Review
1 0
(5 out of 5 stars) exact replacement for my old part
Reviewed By: John S. from el cajon, CA ()
exact replacement for my old part. pool dealer wanted $175.00...paid only$99.00 thru INYO!
Was this review helpful to you?
The Most Recent Reviews
1 0
(4 out of 5 stars) valve stem for backwash valve
Reviewed By: Jay L. from Temple City, CA ()
Pros: good quality and price
Cons: none
The product I received was as advertised and just the part i was looking for. It even included 2 o-rings. The part had no issues and the price was good!
Was this review helpful to you?