$25.75

Qty:

By Pureline


Details

Top

Part # 4703-23

Manufacturer Code SPX714CA

Dimensions 5" L x 5" W x 4" D

Alternate Part #'s 4703-23, HPPSPX0714CA, SP0714C, SP0714CA, SPX0714CA, SPX714CA, PL0730

Product Description

PureLine® Replacement Diverter with Spider Gasket

Compatible with SP0714T-Style Multiport Valves
Comparable to SPX0714CA

The PureLine® Diverter and Spider Gasket assembly is an aftermarket replacement designed for use with multiport valves similar to the SP0714T model. If you're experiencing leaks from the backwash port, it’s often due to a worn-out spider gasket—this replacement diverter assembly solves that issue with a pre-glued 4-spoke gasket.

Key Features:

  • Includes diverter (key assembly) and integrated 4-spoke spider gasket

  • Gasket is permanently affixed and not sold separately

  • Designed for top-mount 1.5” multiport valves used on many sand filter systems

Commonly Used On:

  • Valves marked SP0714T

  • Top-mount sand filters with models:

    • S166T, S180T, S190T, S210T, S220T, S230T, S244T, S270T

Easy DIY Installation
No special tools required.
Watch our video: How to Replace a Diverter and Spider Gasket on a Multiport Valve

Included in Package:

  • Diverter (Key Assembly)

  • Pre-glued Spider Gasket

Disclaimer:
All manufacturers’ names, brand names, trademarks, images, symbols, descriptions, and part numbers are used herein for reference purposes only. This product is not manufactured, endorsed, or affiliated with Hayward® or any of its affiliated companies.

Easy Homeowner Installation

Watch our Video on How to Replace Your Hayward Diverter with Spider Gasket

 

Top

?     Asked on 8/29/2014by Guest

Does this come with the 2 o-rings for around the neck?
 Reply

A  Answered on 8/29/2014 by InyoPools Product Specialist Patrick P.

No, they are sold seperatly. They are part number 4700-08a.
 Reply


?     Asked on 3/25/2015by Jerry

How do you get the old key. Seal assembly out of the old shift handle housing Th tension spring is very strong..once out how do you compress the spring to put new key seal & spring and pin back in? Any tricks on spring compression? Jacuzzi 7 pos Diverter valve Any replies would be helpful & appreciated. thank you
 Reply

A  Answered on 3/25/2015 by InyoPools Product Specialist Brian M.

There is in fact a trick. This " How To " should show you a very helpful tip into putting the pin back into the handle.
 Reply


?     Asked on 5/7/2016by Michael Crane

Is the spx0714ca the same part as mine that is labeled spx0714c?
 Reply

A  Answered on 5/10/2016 by InyoPools Product Specialist Lennox H.

Hi Michael, The SPX0714CA and SPX0714C are the same parts.
 Reply


?     Asked on 6/14/2016by Inyo Visitor

My handle broke of when I tried to move it. Is this the part that I need to put the handle back on?
 Reply

A  Answered on 6/16/2016 by InyoPools Product Specialist Lennox H.

Hi, If you have the SP0714T Valve and the handle is in good condition but the part that the handle is connect to is broken then yes. If the handle is broken then you will need to replace the Handle-SPX0710XF.
 Reply


?     Asked on 7/3/2016by Rose

Is this compatable with sp0714c
 Reply

A  Answered on 7/6/2016 by InyoPools Product Specialist Lennox H.

Hi Rose, Yes. This Key/Seal Assembly is compatible with SP0714C.
 Reply


Top
Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Hammer/Nail-set, Large Wood Clamps

4     0

Original was leaking

Written on 7/13/2021 by Guest

1 - Remove Valve screws and pull out assembly.
2 - Use hammer and Nail set to knock pin out of handle releasing old Diverter
3 - Unless your spring is worn you may have difficulty putting it back together (I replaced with a fresh spring at the same time). I found it necessary to use two clamps to squeeze down the spring pulling the two parts together enough so I could then align the holes on the handle with the hole on the Diverter. This allowed me to put the pin through and tap it in place. Without clamps I am not sure how I would have done it (don't understand how other DIY stories skip this - without clamps or a friend not sure how I would have gotten it back together - without clamps it requires two hands to squeeze the two parts together evenly (I didn't do this initially and broke the part) and then a third hand to put the pin through).
4- Once re-assembled - screw back into place - make sure all gaskets are in place - and lube them if desired.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver

4     0

Diverted handle broke

Written on 8/9/2020 by Guest

Removed valve body on valve.
Remove diverted.
Replaced diverter and the handle.
Reinstalled the valve.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Pliers

3     0

Filter valve was leaking

Written on 6/18/2019 by Guest

Turn valve to close. Remove screws pull valve apart. Replaced new part. Put back together

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Hammer

6     1

Spider gasket repair

Written on 5/5/2018 by Guest

Removed plate, popped out pin on handle, removed old gasket apparatus, replaced with new part, put pin back in handle

Were these instructions helpful? 
 

Top

Review Summary

 (Average 4.8  out of 5 stars)
25 Rating
5 star:
 
(22)
4 star:
 
(2)
3 star:
 
(0)
2 star:
 
(1)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews