Part # 4703-20
Manufacturer Code PL0734
Dimensions 7-3/8" x 6-7/8"
PureLine Upper Handle Assembly for Hayward SP0714T Valve
This is the upper handle assembly by PureLine for the Hayward SP0714T Valve. Normally when you start to see leaking from your backwash port or you handle becomes hard to press down then it is a good time to replace your handle assembly. This is an after-market part and not the O.E.M original by Hayward.
Easy Homeowner Installation
Watch our Video on How to Replace Your Hayward Upper Valve Assembly
Commonly Used On
Included with Upper Valve Assembly
Is Hayward part number SPX0714BA (4703-20) the correct Key, Cover, and Handle Assembly for the Hayward XL SP0714T?
Reply
Yes, Hayward part number SPX0714BA is the correct Key, Cover, and Handle Assembly for the Hayward XL SP0714T.
Reply
The valve handle on my SP0714T broke in the assembly valve. Do I need to replace the entire SP0714T or just replace the key cover and handle assembly part SPx0714ba? Are other parts needed to replace this part?
Reply
You do not need to replace the entire assembly valve to replace the handle. You can either take apart the top valve assembly and replace the handle or replace the top valve assembly as you have suggested. More commonly people replace the entire top for it is easier and also replaces the small parts inside of the top vave assembly.
Reply
I need to purchase a new key cover for my sand filter. I found the number inside of the key cover asd SP0714A. I find no item matching that number. Please provide information if this number has changed.
Reply
Hi Sandy, The SPX0714BA on this page would be the correct replacement key cover and handle assembly for your SP0714A.
Reply
my part number is sp0714c.when turning the handle a white is sticking along side and causing not to turn do I replace the hole they or remove handle to replace ,and how do I get the pin out. I think I would like to replace .it would be a lot easier for me. can I use this part number.
Reply
Yes you could use this part to replace the top half of your Hayward sp0714c valve, I think this would be the best route for you.
Reply
Less than 1 hr
Screwdriver, Wrench Set
1 0
Less than 1 hr
Screwdriver
1 0
Less than 1 hr
Screwdriver
1 0
1. I purchased a Key, Cover and Handle Assembly (PL0734) from INYO pools.
2. I watched the video of how to replace the KCHA and took notes.
3. After receiving the new handle assembly I removed the defective one from the sand filter.
4. I replaced the defective one and replaced it with the new one from INYO pools.
5. I tested it and there was no longer a leak.
6. I celebrated because it was so easy to do!
Less than 1 hr
Screwdriver
2 0
Less than 1 hr
Screwdriver
1 0
Less than 1 hr
Screwdriver
2 0
First took off old assembly by removing the 5 screws. Spread Teflon lubricant on gaskets and O ring. Replaced the old assembly with the new assembly by lining up the tab. Replaced the 5 screws. Project completed successfully.
Less than 1 hr
Screwdriver, silicone lub
2 0
First turn off pump. Turn off water valves to pool or install winter plugs to keep pool from draining. Remove Philips screws from around the valve and pull straight up on the valve. To install reverse instructions put some lubricant on all rubber O-RINGS to make installation easier.
Less than 1 hr
Screwdriver
1 0
Remove screws pry out valve handle assembly. Be sure and use the lubricant I purchased with the valve as the gasket is already glued in. A thirty-minute job with no frustration and cost-effective to Heyward part. Thanks for a good product
Less than 1 hr
Screwdriver
1 0
Less than 1 hr
Screwdriver
2 0
EASIEST POOL FILTER REPAIR I'VE EVER MADE. BOT THE KEY, COVER & HANDLE ASSEMBLY #SPX0714BA AND "O" RING #5000-4053. USING A LG PHILLIPS SCREWDRIVER I REMOVED THE EXISTING 6 SCREWS ON THE TOP OF THE ASSEMBLY, LIFTED OUT THE ENTIRE LEAKING ASSEMBLY, PUT THE NEW O RING ON AND THEN REPLACED THE ENTIRE ASSEMBLY WITH THE NEW ONE, REPLACING THE SAME SCREWS. RESULT - NO MORE LEAKING WATER FROM THE DRAIN.
Less than 1 hr
Screwdriver
1 0
I had went to the local pool store to get the parts needed to fix my pump. However, when I purchased them I paid more and got less. I found this website and ordered my hole kit that I needed for less than what I had just paid. Shipping was on time, actually a day early. I took the old part off and out the new one on, and the pool pump has worked wonderful ever since. I will be ordering from this company again. Thanks for the speedy shipment and great pricing.
Less than 1 hr
Screwdriver
1 0
Ordered the part from into pools and when I got it there were six screw on top that pulled it out of the valve body, of course you shut the pump off to do the repair, greased up a new. O ring seal and the spider seal stuck it back in and turned the pump on. 10 minutes total time from shut off to start up.
The Most Recent Reviews
2 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Easy to install, but it comes with an O-ring so you don't need to buy an extra one (like I did).
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
perfect fit. half the price of everywhere else.
Was this review helpful to you?
1 0
(1 out of 5 stars)
Reviewed By: Inyo Customer ()
It leaks water out of the drain pipe.
Was this review helpful to you?
2 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Found my valve assembly was leaking water out the backflush/ waste port when in filter position and at an alarming rate. I ran a hose from port back to pool to save the water whilst I looked for a replacement assembly. Found this not name brand one “Purline “ one at a substantially cheaper price than most websites and name brand assemblies and purchased it and received it within a few days. Followed installation instructions and 5 minutes later had the leak fixed and filter back to filtering..great price and assembly easy and smooth to use. Only thing is that the assembly comes with the o ring which is not stated in the description of unit. So no need to buy o- ring separately…other than that very pleased with INYO pools service and products thus far.. will probably order from them again
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Good product , i had to push it really hard to fit it but it worked
Was this review helpful to you?
1 0
(5 out of 5 stars) Should've replaced this a year ago! Smooth operation agas now!
Reviewed By: Inyo Customer ()
Great product, great price, easy installation. See the instructional step by step below.
Was this review helpful to you?
1 0
(5 out of 5 stars) Filter handle replacement
Reviewed By: Inyo Customer ()
Drop in replacement for Hayward sand filter valve
Was this review helpful to you?
(5 out of 5 stars) WHEN YOU BREAK YOUR HANDLE CAUSE YOU DID NOT SHUT OFF THE PUMP GET THIS.
Reviewed By: Inyo Customer ()
THIS FIXED IT! DID NOT USE OTHER PARTS YET.
Was this review helpful to you?
1 1
(5 out of 5 stars) Worked great
Reviewed By: Inyo Customer ()
Worked great and only took 20 minutes to change out. Most of that time was spent cleaning the old lube out of the valve body. Used Magic Lube and don't expect to have any issues in the near future. The replacement part was a 100% match at an excellent price. The Magic Lube was also excellent and shouldn't leave the residue the old lube left.
Was this review helpful to you?
2 0
(5 out of 5 stars) Fast and Free, no joke.
Reviewed By: Inyo Customer ()
Came the very next day! Worked great!
Was this review helpful to you?
2 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Exact fit
Was this review helpful to you?
1 0
(5 out of 5 stars) Easy order
Reviewed By: Inyo Customer ()
Ordered this part and received it 3 days after order. Matches up perfectly.
Was this review helpful to you?
1 0
(5 out of 5 stars) Ease to install
Reviewed By: Z.C. from Georgia ()
Pros: Very easy to install
Was this review helpful to you?
7 0
(5 out of 5 stars) Key Cover and handle assembly
Reviewed By: Jeanne Y. from Virginia Beach VA ()
Pros: very easy to install - took 5 minutes
Cons: none
I was having problems with my Haywood sand filter leaking water through the backwash hose while in filter. I spoke to a very helpful customer service man and he told me exactly what to get and even how to install it. It was so simple to install just like the man said it would be and it works great! Not only is the problem fixed, I can read the display again since it is part of the replacement. I did also get the o-ring and pool o-ring lube that was not included to make sure I had a good seal
Was this review helpful to you?
4 0
(5 out of 5 stars) Works like a charm! Smooth!
Reviewed By: vefmom3 from Stuart, VA ()
Needed this part asap! Got it ASAP! Was cleaning my pool to close when the handle broke and I couldn't do anything. Only wish I had thought to order the O ring that went with it but my "old" one worked.
Was this review helpful to you?