Hi, the old pump currently in my pool has an item number 717744903 with serial number BU714. Would this part be a good replacement to my old pump?
Reply
I have a sta rite s48a53a03 motor for my above ground pool and want to replace it. Is this the correct replacement motor? what other kits will I need? Thanks
Reply
Hi Bill, Yes this is the correct replacement motor for you s48a53a03 motor. The most common Sta-Rite pump this motor was used on was the JWPA series, if you have a JWPA pump then you would require the Sta-Rite JWPA Shaft Seal. If you don't have the JWPA pump then send us an email with your pump model or a picture of your pump and we will let you know the shaft seal you need.
Reply
My pump motor has the number 7 186884 20 . Will this motor work as a replacement for my motor?
Reply
We are showing that part # cross references to the 1 HP BN25SS Motor here.
Reply
I have an Optiflo 347986 1.5 HP that I need to replace. I'd like to replace it with a 1 HP duel speed motor. Can you help me with the replacement including shaft seal kit? Also, does it come with an on/off switch including toggling between the speeds? Thanks
Reply
Hi George, If you replaced your 1.5 hp motor with a 1 HP dual speed motor then this would require that you replace your motor, impeller, tune up kit and you would need to purchase a switch separately. All of these items would cost more than a new 1 HP dual speed pump. With this being said I would suggest the 1 HP Dual Speed Dynamo Pump the Dynamo pump does have the hi / lo switch integrated into the motor. It does not come with a cord as you would use the cord from your old pump for the new pump.
Reply
I have a JWAPA5E7L-A2 HORIZONTAL MOTOR that just died will this one take it's place? So, I can get me pool going A.S.A.P?
Reply
Hi Bernie, if you are looking to replace the motor on your Sta-Rite JWAPA5E7L-A2 pump then you would require the 1 H.P. BN25 Motor as well as a Sta-Rite JWPA Shaft Seal.
Reply
Is this the correct replacement motor for JWPA5F7L-2A1? Everything seems to match except for the Frame - mine says 56Z. Will this motor fit properly, and do I need any additional parts such as the optional spacer to make it fit? Thanks.
Reply
Hi Art, The 1.5 H.P 230/115V Thru Bolt Motor (BN35, BN35SS, BN35V1) will be the correct replacement motor for your JWPA5F7L-2A1 pump. You will need to replace the Shaft seal and o-rings which can be found via the Sta-Rite JWPA Series Parts.
Reply
Hi,
my motor is BN35, part 7-177615-02
Also have a BN34, part 7-177783-02
will this work as replacement for both?
Reply
Hi AG, The 1.5 H.P 230/115V Thru Bolt Motor (BN35, BN35SS, BN35V1) would work as a replacement for both motors. Make sure that motor is wired to to correct voltage.
Reply
My existin part number is model Jwpas5f-2a4. Will this one work as a replacement?
Reply
Hi Teresa, This motor can also work with your JWPAS5F-2A4 pump, it will actually be a direct replacement. I would also recommend replacing the pump shaft seal and o-ring which can be found via the Sta-Rite JWPA Series Parts.
Reply
I currently have a Sta-Rite Pump Model JWPA5FL-2A, would part BN35V1 be a suitable replacement ? What would you recommend, thank you for your advice & time.
Reply
Hi Brian, The BN35V1 motor is the correct replacement for the JWPA5FL-2A pump. I would also recommend that you replace the shaft seal and o-rings which can be found on the Sta-Rite JWPA Series Parts page.
Reply
Where can I find motor thru bolts that includes the length required for the mounting of a Hayworth pool pump.
Reply
Hi Mark, You can contact Hayward at 908.355.7995 or Century at 937-667-2431 for the thru-bolt size.
Reply
looking for a replacement motor for S48B74A03 DAYTON 1.5 SPL....JWPAS5F-2A4
Reply
Hi,
i have a purex triton dynamo motor cat # BV35, 1.5hp, 115 volt rpm3450,
is the BN35 replacement correct?
Reply
how to wire pump to 230 volt
Reply
Hi, When wiring this motor for 230 volts you will use the L1 and L6 terminals. Since both leads are 115 volts it does not matter which lead is placed on L1 and L6. Then your ground goes to the green screw.
Reply
need to replace ultima circ pump on hot tub , 220 volts ,1 speed, 0.25 horsepower , 2 3/8 od thread to thread , model # 1030010
do you guys carry a replacement , does the horsepower need to be the same as old one if it is not thanks
Reply
Good morning Don, Unfortunately we do not carry that motor. The only way to get that low of a horsepower is to get a dual speed and run it on its low setting. You do not have to get the same horsepower but if you change the size of the motor you will have to change the impeller to match. By changing the impeller you are pumping more water changing pressure and flow. Here is a link to all the parts we sell for that current pump. Vico Ultima & Ultima Plus Pump Parts
Reply
I need a replacement motor for Pentair dynamo 1.5HP Motor 193262 part#340318. Which motor would I order from you?
Reply
Hi, Pat. Based on the info provided the BN24V1 would be the correct replacement motor. The 1.5 HP SPL rating on the pump is a special (SPL) labeled model. It does not refer to the actual horsepower of the motor. I would also recommend that you get the Dynamo Tune Up Kit - GOKIT46.
Reply
Replacement for a FLOTEC AT251501-01 1.5HP motor.
Reply
Hi, Jim. The replacement motor for the Flotec AT251501-01 is UQC1152. I would also recommend getting the replacement seals which can all be located on the Flotec AT251001 & AT251501 Parts Diagram page.
Reply
does this motor use a start capacitor ?
Reply
Hi, Joe. Yes, this motor uses a Start Capacitor - BC-86.
Reply
I want to replace an Pentair optiflo 1 1/2 hp 115 volt motor with a 230 volt so I can add my heat pump. will this motor hook up to my pump 347989?
Reply
Yes, this motor will mount to an Optiflo pump housing.
Reply
I need to replace an A. O. Smith 1.5 HP motor on a Hayward pump, part O-187873-20. Which motor do I need to purchase? Thanks.
Reply
You would require this BN25V1 Replacement Motor
Reply
I'm trying to replace sta-rite jwpa5el-2a, i can't find anything..is there any replacement that will work?
Reply
Hi Sarah, I like the PureLine PL1501 1 HP Pump as a replacement to your sta-rite jwpa5el-2a. Please note that the plumbing ports on the PL1501 are not in the exact same spot as the Sta Rite pump so you may have some re-plumbing.
Reply
I want to know if the Magnetek BN35 or BN35SS listed on your website will be a compatible replacement for a 17 year old Magnetek 1.5 HP pump that shows a Cat. # of BN 37?
Thanks,
Marty
Reply
Need a replacement pump/ motor for sta brite JWPA5FL-2A1 or motor for A.O. Smith
S48A53A03
Reply
Hi, Dan. This Century BN35V1 Motor is the correct replacement motor for the AO Smith S48A53A03. I would also recommend getting the Sta-Rite JWPA Seal Kit 1 & 1-1/2 HP - APCK1187.
Reply
Hello,
Our above ground proline pool pump is not working. Would you be able to suggest a
replacement that would fit this filtering system. The model number is
PE71-ii-H serial number 379343.
Thank you
Reply
I have a Pentair PLM100 cartridge filter system that used a model # C48M2A24B1 motor on the pump. That motor is now obsolete, so would this motor work with 115 volt and pump? Also, what else would I need to change the motor?
Reply
Hi, i am replacing this motor. Will the bn35 replace this. picture attached
a.o. smith ,pd s48a53a03 it also has this number at the top #u27-1064
Yes, this would be the correct motor replacement.
Reply
I have a Leslie's hydramax II pump with a century 1610-z 1 hp Motor on a 230 Volt power source, I need to replace the motor and be California compliant.
Can I upgrade to a variable speed motor? if so which motor and which pump parts and seals should I replace, I also run a Polaris 380
sweep off of this pump
Reply
Hi, Gary. Yes, you can use the ECM16CU along with the Tune Up Kit - GOKIT2 or GOKIT2SALT to convert your existing pump to variable speed operation.
Reply
https://photos.google.com/u/3/photo/AF1QipOghARQA2hY0GzNDAHKzXH8Rxephv-mLgoSXaW3
This motor is bad out of my Caldera Spa
Will a BN40 A.O. Smith motor replace it ?
Reply
Hi, Brad. The link to the image did not work. Please try uploading the image as a file so that I can confirm.
Reply
Looking to replace the hayward motor. Here is my current motor.
Hi, Paul. The replacement motor will be the BN25V1 or SPX1515Z1E. The motor you have has a specialty rated hp.
Reply
how do you attach the motor to the basket
Reply
Ultimately, this will depend on the model of the front pump housing that the motor actually bolts to. There are many. If you can provide that in an email to uplaod@inyopools.com we may be able to locate a parts diagram or maybe even some content that may walk you through that.
Reply
I need a replacement filter basket with lid for my century pump number 186886. Can you help with that?
Hi, Neil. You can use the Complete Trap Assembly - 25300-004-000 with your model wet end.
Reply
I have a AquaMite Series pump with a M# 2402200DU (2HP) 115 volt motor on it. What is the replacement motor model number?
Thanks
Reply
Hi Wink, Could you send us a close-up photo of the motor label as well as a wide shot showing the complete pump including where the plumbing that goes in and out of the pump. To send your photos simply click the reply link below and upload your photos.
Reply
Would this work to replace my motor? Also, the motor has just quit, is there a reset on the system maybe somewhere or is the motor probably just dead? It was running one moment then nothing the next. Thank you in advance
Hi, Vivian. There is not a reset switch. This motor is not compatible with your model pump.
Reply
Hi,
I have a Starite Posi Clean JWPS5FL-A2. Would this be the correct one? Thanks!
Reply
You are correct, the BN35V1 is the correct motor replacement for the Sta-Rite JWPS5FL-A2
Reply
I Have an bn35 Ser# 177615 frame r48y will this replace this what other parts will I need like seals and impeller
Reply
Yes, this is the correct single-speed replacement for your motor model but in order to cross-reference the correct impeller and seals, we will need the model name or number of the front pump housing that the motor bolts to. If you are not sure of that model you can always send us images to upload@inyopools.com so we can confirm.
Reply
I just bought a century bn35v1 motor from you, hooked it up and discovered that it must be set to 230 volts since it cycles constantly. How do I change the voltage on one of these?? (The chart on top talks about blue and brown wires which are not in evidence when I take the back cover off)
Thanks
Reply
Single-speed motors go out wired for 230v just in case the supply voltage is wrong. You can supply 110v to a 230v motor without doing damage, supplying 230v to a motor wired for 110v will cause damage. Take the black wire that should be on the # 5 terminal & move it to the # 6 terminal.
Reply
Single speed motors go out wired for 230v just in case the supply voltage is wrong. You can supply 110v to a 230v motor without doing damage, supplying 230v to a motor wired for 110v will cause damage. Take the black wire that should be on the # 5 terminal & move it to the # 6 terminal.
Reply
I currrently have a Pentair Optiflow 1.5hp pump motor (347986 is the complete pump assy #) .
230/115V
60hz 1PHkW
3450RPM
Looking to replace with AO Smith.
What is the compatible new pump # that I can use the old pump head parts with? Just need the motor. On website I think it would be BN35V1. Please confirm....thanks
Yes you can still use the same housing and that is correct the BN35V1 is the correct replacement motor.
Reply
I have a BN35V1 WITH impeller but can not read a part number for impeller. What impeller do you recommend? Thanks
Reply
Hi, Terry. We will need to know the model of the pump that this motor operates in order to locate the correct replacement. You can also provide pictures of the pump so that we can identify it.
Reply
I have a Watkins 36675 pump with a Magnetek 7-187100-02 1.65 HP motor 115 VAC. Will this motor work for a replacement. I bought a new wet end but the shaft of the old motor is bad.
Reply
Unfortunately that motor is no longer available with no listed replacement. You may be able to confirm directly with the manufacturer Gecko at 1-866-639-7274.
Reply
I purchased this unit to upgrade and replace my StaRite motor. I wired this up for 115 but after 1 minute of operation it began to smoke and over heated. I am not sure what is wrong with this motor can you give advice on how it is supposed to be wired as as the picture on the motor for the lines may be incorrect. thank you in advance.
Reply
You may want to call Pentair ( StaRite ) direct help line it sounds like you are sending too high of voltage to motor and you need to wire it correctly. 1-800-831-7133 .
Reply
Generally what you are describing is sending 220v to a motor wired for 115v, which will do exactly as described. Sending 115v to a motor set up for 220v does not usually create any damage. see images we added
I do understand what you say about 220 V/A/C, but I only have 115 V/A/C to that circuit because that is what the previous pump used so that is not the issue. I am not sure what the images show because you offer no direction to what the circles mean. would you please clarify your explanation. thank you in advance.
Reply
Would this pump work to replace an Ultima 1.5 HP 60HZ 115 Volt 2 Speed pump model # 1014244. We only need the pump and not the wet end showing in the attached pictures.
Thank you,
does this motor work as a replacement for a 1.0 hp SP1510 motor with same everything else? I need a new motor but also want to upgrade to a 1.5 horse motor?
Reply
Yes, the Century 1.5 HP Thru-Bolt 48Y Motor - BN35V1 can be used with the SP1510 pump and Impeller 1.0 THP - SPX1500L (OEM impeller rated for 1, 1.5 and 2 HP. Used on the Hayward Matrix, Power-Flo 1500 Series, and Power-Flo LX.) The Tune Up Kit Power-Flo 1500 Series - GOKIT12 is needed when replacing the motor. The Power-Flo LX 1 1/2 HP, 115V, 1 Spd. Pump - W3SP1580X15 or Power-Flo LX 1HP, 115V, Single Spd. Pump - W3SP1580 are available too as whole units.
Reply
I have a Hayward power flow lx pump. SP1515Z1BC Part # O-187873-20 115 volts 12 amps Serial # 10813CH. I need this replacement pump.
Reply
If you are looking to replace your complete pump then you will require this Hayward 1.5 HP Power Flo LX Pump if you are just wanting to replace the motor then you will need the BN35V1 motor listed on this page as well as this Hayward Power Flo LX Shaft Seal
Reply
Does this pump replace my old pump.?...because I have a 2hp pump...and don't want to go lower on hp...unless this is my only option?...and will the plug end be the same?......see photos
Hi Bob, Yes this motor is the exact same power as your motor in the photo. You have 2 HP SPL and the SPL HP is identical to a standard 1.5 HP motor. The motors do not come with a cord and plug so you would remove your cord and plug from your old motor and attach it the new motor. The process is quite simple just remove a few screws.
Reply
I am looking to replace my pool motor/pump. The brand was waterway, serial # SD140207 0020, model # SD-15-2N11CC, part # PEW2150-3GRP. Can you tell me whether this pump would replace it or which pump could be compatible?
Hi Becky, You would actually need this BN37V1 Motor the BN37V1 is a 1 HP standard motor and your motor is a 1.5 SPL motor. The 1 HP and 1.5 HP SPL are the identical HP. Your current motor is a dual-speed motor and the BN37V1 is a dual-speed where this BN35V1 is a single speed.
Reply
what is the shaft seal model number BN35v1 1/2 shaft
Reply
For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
Would this motor replace a Century HP 1.5 spl, part# 7-17760-23
Hi Ronda, the correct replacement motor for your motor part number 177760 is the BN25V1. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I need a replacement motor for my pool pump. It has a 1.5 hp Hayward single speed motor, model number is SP1515-Z-1-ESC. I seen the BN35V1 motor for sale on your web site and lists several alternate part numbers on it. There are several part numbers listed that are almost identical but are missing the "C" or the "S". Would this motor still be compatible with my Hayward Power Flo Matrix SP1593 Pump?
Yes, this would be a compatible replacement motor for the model SP1515-Z-1-ESC motor.
Reply
Will this motor replace mine?
Hi Dave, yes, this is the correct single speed replacement motor for the motor included in your photo. You will also need a Hayward Powerflo LX shaft seal when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
is century model nbr hsq125 compatible with bn35v1
Reply
Hi Miguel, the correct single speed replacement motor for your motor model hsq125 is the USQ1102. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
what impellar and diffuser model number do I need toget
Reply
Hi Miguel, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
Will this motor replace the motor in the Jacuzzi pump? Jacuzzi P/N S15LRDV, Current Motor is an AO Smith 7-186050-2, Serial# BX4-29. See Pictures. Thanks
You are correct. The BN35V1 is the correct replacement for your 7-186050-21 pool pump motor.
Reply
Is there a gasket kit required when changing the motor?
Reply
Yes you will need this Jacuzzi SLR Gasket Kit when replacing your motor.
Reply
Is this compatible with the HAYWARD POWER - FLO SP1515Z1BC?
Reply
Hi Juliet, yes, this is the correct replacement motor for the pump model SP1515Z1BC. You will also need a Hayward PowerFlo shaft seal when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Is the shaft length and diameter always the same with a Y48?
Reply
Hi Stephen, shaft seal dimensions and versions will vary based on the model of the front pump wet end housing the motor attaches to.
Reply
I have a Magnetek 1.5 hp 240vac motor. It just hums when i apply power. I replaced the 25uF capacitor. It started once, then hummed on the next start try. I'm going to try a 30uF capacitor. If that doesn't work, what motor do I need as a replacement and do you have a replacement seal ring and/or thru bolts too?
Thank You
Hi Tony, We believe the correct replacement motor for your pump is this STS1102 Dual Speed Replacement Motor. However, could you take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can confirm the proper replacement motor.
Reply
Thank you!
Thanks Tony thats exactly what we needed! You will require this STS1102 Dual Speed Replacement Motor as well as this Jacuzzi Magnum Tune-Up Kit. The motor suggested is a 1 HP Full Rate Motor which is the exact same HP as your 1.5 HP Up Rate motor. The math works as follows 1 HP Full Rate = 1 HP x 1.65 Service Factor = True HP of 1.65 and 1.5 HP Up Rate = 1.5 HP x 1.10 Service Factor = True HP of 1.65. The new motor has an external capacitor so you will need to slide the motor nut which secures the motor to the pump over the front side of the motor and not the backside.
Reply
Can this be used as a replacement for the Pentair pool pump motor, pump model #342352? (http://www.inyopools.com/Products/03500000039733.htm)
Hi Joel, the correct single speed replacement motor for the motor included in your photo is the B854. You will also need a Pentair Pinnacle seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Ok - thank you.
Reply
Will this motor fit the Hayward power flo matrix 1.5 hp?
Reply
Hello. Yes, the Magnetek Century 1.5HP motor BN35V1 is compatible with the Hayward PowerFlo Matrix Pump. It is recommended that the motor shaft seal, o-rings, and gaskets be replaced at the same time. The GOKIT74 contains all the necessary parts to complete this project. Tune Up Kit Hayward PowerFlo Matrix Pump - GOKIT74
Reply
Hello,
Is this the correct replacement for Sta Rite JWPAS5F-2A4?
Additional info PMP 1.5HP SPL 115V VD
Thanks, Larry
Reply
Hello Larry,Yes the BN35V1 is the correct motor replacement for the JWPAS5F-2A4
Reply
I have a 2HP optiflo pump #340078; are replacement 2HP motors available, or would a 1.5HP motor be suitable with a 150 sq. ft. cartridge filter?
Hello. According to Pentair, the Magnetek Century 1.5 HP Thru-Bolt Motor model BN35V1 is a compatible replacement motor for the Pentair Optiflo Pump model 340078. The Impeller does not need to be changed with the new motor installation. It is recommended that the motor shaft seal and seal plate o-ring be changed concurrent with the new motor. Pump Shaft Seal 5/8" - PSR-200 O-Ring, 5-1/2" ID, 3/16" - 357 O-150
Reply
Will this replace a pentair dynamo 1.5 motor
Hi Joel, the BN35V1 motor is not quite correct. Your 1-1/2 SPL HP Dynamo Pump actually uses this BN25V1 motor (the amps are the dead giveaway). Manufacturers play games with horsepower ratings, and there is no industry standard for the definition of SPL or "Special" horsepower. Don't forget to use the GOKIT46 Tune-Up Kit when you replace the motor for all new o-rings and a new motor shaft seal.
Reply
I’m looking for a replacement for a waterco motor. Was wondering if this was the correct model.
Hi Jerry, yes, your 1.5HP Waterco SupaMite Pump uses the Century 1.5 HP Thru-Bolt 48Y Motor - BN35V1 as the replacement motor. We recommend ordering a new motor shaft seal, pump body o-ring, and diffuser gasket to make it work like new and remain leak-free for a long time.
Reply
Does this motor replace the JWPA5YFL-A2
Reply
Hello, yes this motor is a suitable replacement for your original Sta Rite pump model JWPA5YFL-A2. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Key numbers 7 and 9 on this parts diagram are most commonly replaced on your pump series.
Reply
Will this be a suitable replacement for my pool motor, I've attached a photo of mine.
Hello Jared, the correct motor replacement for your motor part number s48aa11a79 is the BN25. These "SPL" labels often confuse pool owners. When replacing a pool pump motor we also recommend replacing the seals and gaskets. For your Waterway Eco Kleer pool pump the seals most commonly replaced are key numbers 11, and 14 on the parts diagram that you can view by clicking here.
Reply
Can I use this to replace s48m2a8a1 which is a 56z frame?
Hello David. According to the manufacturer, Regal Rexnord, the A. O. Smith motor S48M2A8A1 has been upgraded to the Century (A.O. Smith) 1.5 HP Up Rate Thru Bolt Motor, Square Flange 48Y Frame, Single Speed - Model BN35V1 Regal Rexnord - S48M2A8A1
Reply
