Part # GOKIT3
Standard tune up kit for the Hayward Super Pump includes the shaft seal and all o-rings, gaskets and lubricant.
We highly recommend replacing the shaft seal, o-rings and gaskets when replacing your motor. If you use your old shaft seal, it will not mate up properly with the new motor and may leak.
This Tune Up Kit Works on These Pumps:
Tune Up Kit Includes:
For more Pool Pump Motors
Click here for Saltwater Pool Tune Up Kit (GOKIT3SALT)
I recently changed my pool motor and gaskets. I made sure to lubricate all the gaskets with vaseline. A few days later water is leaking from the pump. What did I do wrong? Help please!!
Reply
You never want to use vaseline on any rubber gaskets or o-rings. Vaseline is petroleum based and will deteriorate the rubber quickly. Whenever you change the motor on a pool pump it is recommended that you replace the gaskets and shaft seal as well. A >Go-kit contains the shaft seal, packet of non-petroleum based lubricant and gaskets you will need for your pump. If you already have the gaskets, you can purchase >Magic Lube.
Reply
My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?
Reply
The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.
Reply
Will the GoKit3 work with saltwater pools?
Reply
The Tune Up Kit Hayward Super Pump for saltwater pool is GOKIT3SALT.
Reply
I have a model C48K2n143B1
SP-1607-Z1-M
Which seal kit do I need?
Reply
1 to 2 hrs
Nut Drivers, Socket Set, Magic Lube
1 0
First off, the instructional video's on your site are invaluable! I used this kit with a new century pump I purchased from INYO. As long as you follow the steps in the video, you can't go wrong. Be sure to use the supplied lube ( I always have a tube of Magic Lube around for back up),
1 to 2 hrs
Screwdriver, Nut Drivers, Socket Set, Wrench Set
2 0
I bought this kit to fix my pump. I also bought a new motor. Inyo's YouTube has some great videos on how to do the repair. It was relatively easy. I didn't need a new pump, just the motor, but while everything was apart it was time to upgrade the rest of the elements. Turn off the electricity, disconnect the wiring, remove the bolts holding the motor to the pump housing, replace the parts and reassemble. This was the first time I've done this and the whole thing took about 2 hours.
Less than 1 hr
Socket Set
2 0
Disconnected the pump and replacement the rings. It was self explanatory and everything fit exactly where the old ones came off. The lubricant supplied with the kit was enough to use for the entire kit. Inyoupools has youtube videos or videos right on their website to help walk you through step by step.
Less than 1 hr
Screwdriver, Just to get the old seals out
3 0
We replaced the motor, but didn’t have to replace the debris basket. However, at the suggestion of a product specialist, we did go ahead and replace the seals on anything adjacent to the new motor. We are glad we did! The parts arrived as described and fit well.
Less than 1 hr
Screwdriver, Nut Drivers, Pliers, Socket Set, Adjustable Wrench
2 0
Shut off power remove plastic cover take four bolts off place hex wrench to hold shaft remove impeller remove shaft seals Used small screwdriver to push washer part of seal clean with dry rag lube using glove place parts back together change out gaskets reassemble and reconnect. Prime pump with water in screen side Turn on pump-no leaks Watched an old U tube video before starting Done in less than hour!
1 to 2 hrs
Nut Drivers, Pliers, Wrench Set, Bearing puller. Multimeter to check motor.
4 0
Replaced bearings, seals and capacitor. I got a 1hp Superpump for free that was thought to be junk. The main issue was very bad bearings especially the front one likely due to an old shaft seal. Because of this the capacitor blow out also. Total repair time was about an hour and cost was $70. Now a have a perfectly running spare with my current pump ~10 years old and getting a little load.
1. Had the necessary, basic hand tools and bearing puller (if you don’t, HF has them cheap an auto parts store will loan them).
2. Disassemble per the Inyopools video. These are pretty standard motors so not hard to figure out.
3. Cleaned and check motor with multimeter, pressed new bearings on.
4. Re-assembled motor per the video.
5. Replaced all the seals. Save the water slinger because that won’t be in the kit.
6. Checked adjustment on v-switch. This is important on the older motors. Inyopool has a video on this too.
7. Replaced start capacitor.
8. Successful test and high-5’s all around.
Less than 1 hr
Screwdriver, Nut Drivers, Wrench Set, Tongue and groove pliers
2 0
Less than 1 hr
Screwdriver, Nut Drivers, Socket Set
2 0
Less than 1 hr
Screwdriver, Socket Set
2 0
Less than 1 hr
Screwdriver
2 0
Less than 1 hr
Screwdriver, Nut Drivers, Socket Set
3 0
1 to 2 hrs
Screwdriver, Nut Drivers, Socket Set, Wrench Set
2 0
I replaced my pool motor and INYO recommended this Tune Up kit to replace the seals in the pump. The kit had everything I needed including a small tube of silicon lubricant. All parts were exact replacement and fit perfectly. You simply remove the old gaskets and follow the written instructions and or watch the many videos that INYO Pools makes for your viewing and then ease of performing the job, without having any experience. This was easier than I had anticipated. One thing that was a easy but a little tricky is the shaft bearing is in two halves and they have ceramic faces that must mate. One half is white ceramic and that is easy to see and is well described and highlighted in the videos, but like a lot of things when you're looking at the parts it's not black and white 100% which side of the black ceramic 2nd half of the shaft bearing is the shiny side. You don't want to touch the ceramic surface as the oil from your fingers might cause the bearing to burn... after inspecting closely I was able to figure it out.
Less than 1 hr
Screwdriver, Nut Drivers, Pliers, Socket Set
2 0
Less than 1 hr
Screwdriver, Nut Drivers, Socket Set, Wrench Set
2 0
Remove 4 exterior Motor to pump bolts
Remove next 4 bolts on bezel
Loosen rear metal cover screws
Remove impeller by securing the driveshaft nut and turning the impeller
Remove next two covers attached to motor
Turn off breakers
Remove electrical
Replace gaskets, seals and impeller spring
Reassemble in reverse with new motor
2 to 4 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set
2 0
1. Opened pre-pump strainer basket, and replaced rubber seal in housing top (after lubricating with kit-supplied lube);
2. The following were all replaced after the motor/pump assembly had been removed from the pump housing, and disassembled, per instructional video available online (after being lubricated, of course!):
- Pump diffuser seal;
- Impeller housing-to-motor mount seal;
- Shaft seals in housings (2).
1 to 2 hrs
Screwdriver, Pliers, Socket Set, Wrench Set, Adjustable Wrench
2 0
1. removed old motor from pump housing
2. bolted on new motor to pump housing, as well as replacing old seals with new ones
3. attached impeller and diffuser to motor/pump housing
4. attached new motor/pump housing to filter.
1 to 2 hrs
Screwdriver, Pliers, Socket Set, Wrench Set
2 0
Ordered a new motor from INYO pools. I flt I should get the tune up kit to install it. It was a wise choice as it comes with all the seals needed to replace the motor Installation went smooth.
First took the pump off the filter base. then you separate the motor from the basket. Then remove the impeller and spring bushing. Replace the seal to the basket. The impeller was also worn so I replaced it as well. The motor shaft has a flat section the wold the shaft while you replace the impeller. Reassemble the pump section, note where it is marked top. Put the assembled back on the base. Prime the pump then start it up.
Less than 1 hr
Screwdriver, Nut Drivers, Socket Set
4 0
Pulled everything apart, the seal would not seat. I cracked it. Watched INYO video on replacing pump seals, learned error of my ways, ordered new seal, pump up and running. When am I ever gonna learn??????
1 to 2 hrs
Screwdriver, Socket Set, Adjustable Wrench
3 0
1 to 2 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set, Adjustable Wrench
4 0
1 to 2 hrs
Pliers, Socket Set, Wrench Set
2 0
1 to 2 hrs
Screwdriver, Pliers, Open end wrench
3 0
First I turned off the breaker to remove power. Then I removed the wires from the pump and removed the 4 bolts. That let me take the pump from the front end where the basket and plumbing is connected.
I brought the pump to the workbench and removed the impeller by placing a wrench on the rear of the shaft and turned the impeller until it loosened up enough to remove it. After removal I cleaned up the shaft and removed the seal with a rubber mallet and screwdriver.
My pump was leaking for quite sometime so I had to remove some rust from the underside of the pump and used spray paint to give it some protection. I installed the new seal with care not to touch the ceramic pieces. Next I put the impeller back on the shaft and put the front end which snapped back on.
I then returned to my pump location and fastened the pump back with the bolts I removed. I reconnected the electrical, turned the breaker back on and filled the basket area with water to start the siphon. Within minutes the pump was back working again. This process took me about an hour. My pump is under a deck so it took a little longer to get to it.
1 to 2 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set
2 0
We diagnosed that it must be the motor as, the pump would pump but then trip the circuit breaker. I talked with helpful sales people on the phone and ordered a replacement motor for the Haywood Super Pump. My only mistake was not mentioning that we have a salt water generator and we should have ordered the heavier duty shaft seal, but lessons learned.
Less than 1 hr
None
2 0
Less than 1 hr
None
3 1
There isn’t much step by step to give on this item. I replaced the seals one by one as I disassembled the old motor and put the stuff on the new motor. The gasket for the pump lid was very easy to put on as well as the other ones. The only one I had an issue putting in was at the back of the pump that connected the motor to the pump because it would want to pop out as I went around. Eventually I got my fingers spread out far enough to hold the gasket and got it in.
1 to 2 hrs
Screwdriver, Nut Drivers
2 0
Just replaced pump with a Century 1hp. pump. The greatest part of this evaluation was the fantastic support I received from the on-line videos by InYoPools.com and their friendly and helpful staff. Not only the best prices but best service to boot.
2 to 4 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set, Wire stripper/crimper
4 0
I purchased the correct motor from INYOU and it arrived days sooner than expected. I took the recommendation and ordered the seal kit as well. Finally on Fathers Day I had the time to tackle this daunting project. Always wary of anything electrical, I took every precaution I could to not electrocute myself with my son present. With everything checked and double checked the moment of truth arrived. I three the breakers on and then threw the switch on the timer box and........SUCCESS! The motor turned and the pump started circulating the water. Awesome feeling of overcoming a fear of electricity and knowing I did it right the first time. The tutorials from INYO were perfect and I saved over $ 330.00 doing it myself.
Less than 1 hr
Screwdriver, Socket Set
3 0
Removed pump by disconnecting power removing mounting bolts, impella cover and impella. Replaced pump. Tested same before installation and it didn't work. Contacted customer care and they sent me a new one in two days. Installed same after installing new gaskets upplied in the Super Pump tune up kit and new ceramic bearing
1 to 2 hrs
Screwdriver, Pliers, Socket Set, Wrench Set, Adjustable Wrench
3 0
$266.00
$228.00
$223.00
The Most Recent Reviews
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Perfect match
Was this review helpful to you?
1 0
(5 out of 5 stars) Service beyond my expectations.
Reviewed By: Inyo Customer ()
I purchased this along with a replacement Superpump from Inyo. I gotta tell you, the courtesy, the level of support, the entire inquiry, purchase and shipping process was so easy, man. There’s nowhere else I’d go for my pool equipment because these folks really took care of me when I needed the assistance.
Was this review helpful to you?
1 0
(5 out of 5 stars) Great customer support
Reviewed By: Inyo Customer ()
Very pleased. Just what I needed.
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Worked as expected
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Customer support provided guidance on which seal kit to order and it was the exact replacement for my pool pump.
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Package was delivered on time and good condition!
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Everything fits as suppose to.
Was this review helpful to you?
1 0
(5 out of 5 stars) Complete kit!
Reviewed By: Inyo Customer ()
Complete kit that covers everything you need when replacing your motor. Love that it also has the gasket for the strainer box!
Was this review helpful to you?
1 0
(5 out of 5 stars) Leaking pump fix
Reviewed By: Inyo Customer ()
Great kit, has all the seals to resolve a leaking pump issue. I would recommend watching a video to make sure you get the shaft seals facing the correct way but otherwise a simple repair fix.
Was this review helpful to you?
1 0
(5 out of 5 stars) Quick shipping
Reviewed By: Inyo Customer ()
Shipped quickly and fit as described
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
great product
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Exactly what I needed.
Was this review helpful to you?
1 0
(5 out of 5 stars) If you change just your motor don't forget this kit and get everything working correctly!
Reviewed By: Inyo Customer ()
Perfect kit if you are replacing the motor and keeping your old pump housing.
Was this review helpful to you?
1 0
(5 out of 5 stars) Necessary kit
Reviewed By: Inyo Customer ()
Easy to replace old seals. Their videos are helpful.
Was this review helpful to you?
(5 out of 5 stars) Small but essential piece of the Big Puzzle!
Reviewed By: Inyo Customer ()
This kit necessary for the new pump. Good buy!
Was this review helpful to you?
(5 out of 5 stars) pump internals
Reviewed By: Richard B. ()
perfect item for my pump
Was this review helpful to you?
(5 out of 5 stars) Happy that I had previously purchased this
Reviewed By: Inyo Customer ()
I had purchased this kit in fall of 2022, because it seems the pool always needs a few new gaskets each summer; we had to replace our pump’s motor this summer and I’m glad we had already purchased this kit because we needed a few of the parts
Was this review helpful to you?
(5 out of 5 stars) perfect replacement
Reviewed By: Inyo Customer ()
Perfect fit for seals
Was this review helpful to you?
(4 out of 5 stars)
Reviewed By: Inyo Customer ()
Did not end up using this kit since I ordered the wrong kit I need gokit2.
Was this review helpful to you?
(5 out of 5 stars) Hayward Super Pump Seal Kit
Reviewed By: Inyo Customer ()
Super pump seal kit is a must when replacing the motor. Replaced all the seals to make sure new pump didn’t leak.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Parts were as described and update of motor assembly went well with instructive video.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Perfect fit no leaks..
Was this review helpful to you?
(5 out of 5 stars) correct parts
Reviewed By: Inyo Customer ()
product worked great. Very fast shipping.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
All fit perfectly and no leaks.
Was this review helpful to you?
(5 out of 5 stars) Great product
Reviewed By: Inyo Customer ()
Great fit on the new motor! Thanks for recommending!
Was this review helpful to you?
(5 out of 5 stars) Go kit 3
Reviewed By: Inyo Customer ()
All the seals and gaskets for a Hayward super pump
Was this review helpful to you?
(5 out of 5 stars) Perfect match
Reviewed By: Inyo Customer ()
Ever piece is an exact match. Maybe a little light on the supplies silicone grease. But I do really like to butter up my seals so it’s probably me. Also, if replacing all your seals, don’t throw away your old water slinger. That is not part of this kit.
Was this review helpful to you?
(4 out of 5 stars) The Right Fit for the Job
Reviewed By: Inyo Customer ()
Everything as expected. Some installation instructions would have been helpful
Was this review helpful to you?
(5 out of 5 stars) Just as described
Reviewed By: Inyo Customer ()
Worked great and easy to install.
Was this review helpful to you?
(5 out of 5 stars) Great kit, everything you need
Reviewed By: Inyo Customer ()
Perfect kit with everything you need. Follow instructions here: https://youtu.be/mpJLp3oWDGU
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Thanks for your guidance, the kit was perfect fit
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Great quality materials used and excellent fitment!!
Was this review helpful to you?
(5 out of 5 stars) Perfect fit!
Reviewed By: Inyo Customer ()
Perfect fit for the Century 1.5 replacement motor UST1152
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Right parts for the job
Was this review helpful to you?
(5 out of 5 stars) Buy it. Easy install for a good seal
Reviewed By: Inyo Customer ()
Worked well and fit beautifully. Also had enough silicone gel to get the job done.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Perfect price and Fit
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Worked very well
Was this review helpful to you?
(5 out of 5 stars) Worked great
Reviewed By: Inyo Customer ()
Easy too install
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
excellent product
Was this review helpful to you?
(5 out of 5 stars) Thanks for your assistance.
Reviewed By: Inyo Customer ()
Your sales rep helped me determine that the Pump Shaft Seal was probably causing my leak. He then recommended a Hayward Tune Up Kit to replace those parts as well. The leak is gone and all is working great! Thank you!
Was this review helpful to you?