1. Home
  2. Pool Parts
  3. 5002-08

$252.68

Qty:
 ADD TO CART

By Pentair Pool Products

Details

Top

Part # 5002-08

Manufacturer Code 355302

Dimensions 11-5/8" x 5" D

Alternate Part #'s 355302, 6223, PAC1013125, 35-110-1636, PEN355302

Product Description

Pentair OEM housing 355302 & 355468

Frequently Bought with Front Housing:

Commonly Used On:

Top
Ask A Question

?     Asked on 11/2/2014by Inyo Visitor

Housing front has a small split that is dripping ,is there a repair of sealant that can seal this or other options . thanks for your response.
 Reply

A  Answered on 11/3/2014 by InyoPools Product Specialist Brian M.

Good afternoon. I have not heard of any type of sealant that will do a permanent fix. There is just too much pressure and any epoxy or resin just can not stand up to it.
 Reply


?     Asked on 11/7/2015by Inyo Visitor

What is the difference in Pentair 355468 and 355302 pump housings?
 Reply

A  Answered on 11/10/2015 by InyoPools Product Specialist Charlie R.

Kevin,Part #355302 is a threaded front housing, while part # 355468 is the slip suction version to the same housing.
 Reply


?     Asked on 6/2/2018by Bob Bobek

can u use the 355468 in place of the 355302? will I run into any issues, thanks
 Reply

A  Answered on 6/2/2018 by InyoPools Product Specialist Lennox H.

Hi, Bob. Yes, you can and would not run into any issues. 
 Reply


?     Asked on 3/1/2019by Jim Shannon

Pack Fab pump housing 35-5459 is replaced by 355468 per what I see in the Q & A. So this housing has a slip connection but the diagram shows it attached to the strainer with four bolts an an "O" ring seal. Therefor I am assuming that there is no piping needed to make the connection between these two parts. Is that correct? Thanks Jim
 Reply

A  Answered on 3/8/2019 by InyoPools Product Specialist Lennox H.

Hi, Jim. That is correct, this housing will mount to the strainer using bolts. The threaded description refers to the internal port if you're not using a strainer. 
 Reply


?     Asked on 8/19/2020by Pedro

Hi, I'm looking for a threaded front housing, it has to fit on CFII-N1-5FE / 34-5300 CHALLENGER
 Reply

A  Answered on 8/19/2020 by InyoPools Product Specialist Lennox H.

Hi, Pedro. This Front Housing - Threaded, Black - 355302 is the correct part that you're in need of. 
 Reply



Read all Q&A’s
Top
Write A DIY Story
Difficulty

Est. Repair Time

2 to 4 hrs

Tools Needed

Screwdriver, Nut Drivers, Socket Set

Waterfall Pump was Failing

Written on 3/14/2019 by Guest

I thought it was drawing air through the inlet/outlet threads, but upon disassembly, I found the basket housing had cracked where the top screws down. The pump could no longer provide enough suction to circulate water and was only drawing air. I found a replacement housing here at Inyo Pools and ordered all the required parts to rebuild the water side of the pump as well. Made a short afternoon of disassembly, cleaning, and reassembly all the way back to and including the shaft seal. The pump runs as good as it did when new.

Were these instructions helpful? 
 

Top

Review Summary

 (Average 4.67  out of 5 stars)
3 Rating
(67%) 2 of 3 customer would recommend this product to a friend.
5 star:
 
(2)
4 star:
 
(1)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)
Write A Review

The Most Helpful Review

1     0

 (4 out of 5 stars)  new version but with some extras it worked on old system

Reviewed By:  Gary C. from granbury, TX ()

We have an older system but this worked we just had to make some simple changes and everything is fine. We are ready to swim!


Was this review helpful to you? 
 

The Most Recent Reviews

 (5 out of 5 stars)  

Reviewed By:  Inyo Customer ()

Just what I needed


Was this review helpful to you? 
 

 (5 out of 5 stars)  Hard to find part

Reviewed By:  J Scott S. ()

Novice installer so advice was great


Was this review helpful to you?