Product Description

INYO # 3818-001 DRAINSAFE # DS 360 THIS IS COMPLIANT WITH THE ASME/ANSI A112.19.8-2007 REGULATIONS AS SPECIFIED BY THE VIRGINIA GRAEME BAKER POOL AND SPA SAFETY ACT THIS IS A VGB-2008 COMPLIANT COVER

************************************************

GENERAL DESCRIPTION: 8" ROUND RETROFIT MAIN DRAIN COVER, WHITE (THIS REPLACEMENT COVER IS ABOUT 10" DIAMETER ITSELF BUT IS DESIGNED TO REPLACE COVERS IN THE 8" ROUND GENERAL RANGE)

************************************************

BASIC SPECS: CENTER TO CENTER SCREW HOLE MEASUREMENT: 5-1/2" TO 7-1/2" (REPLACES COVERS WITH HOLES IN THIS THIS SIZE RANGE) USAGE: APPROVED FOR FLOOR OR WALL USAGE SPECS SHOWN BELOW ARE FOR A SINGLE UNIT FLOOR: 123 GPM WALL: 123 GPM LIFE: 3 YEARS TOTAL OPENING: 27.0 SQ INCH

************************************************

DETAILED DESCRIPTION: THIS IS THE DRAINSAFE 360 COVER THIS IS AN ANTI-ENTRAPMENT RETROFIT COVER AND SCREWS THIS COVER DOES NOT HAVE A SINGLE SOLID CENTER TOP PIECE. THE COVER IS DOME SHAPED WITH A VERY FINE GRATING ON TOP. THERE ARE 2 SOLID CROSS PIECES 21/32" WIDE WHICH EXTEND FROM SIDE TO SIDE AND CROSS IN THE MIDDLE. THESE CROSS PIECES ARE THE TOPS OF THE 2 BRACES WHICH EXTEND FROM TOP TO THE BOTTOM OF THE COVER. THERE IS AN OVAL CUT-OUT ON EACH SIDE OF EACH BRACE, WHICH IS WHERE THE COVER SCREWS WILL BE PLACED. EACH CROSS PIECE EXTENDS 1/2" BEYOND THE OUTSIDE DIAMETER OF THE COVER AND EXTEND ABOUT 1/4" BELOW THE BOTTOM OF THE OUTSIDE RING. THERE ARE 2 SMALL FEET BETWEEN EACH CROSS PIECE AT THE OUTER EDGE. THIS GIVES A TOTAL OF 12 SUPPORTS AROUND THE OUTSIDE EDGE. MATERIAL: PLASTIC COVER, STAINLESS STEEL SCREWS COLOR: WHITE SHAPE: ROUND

************************************************

COVER DIMENSIONS: COVER OUTSIDE DIAMETER: 10" (A) (MAIN FLANGE RING) (EACH CROSS PIECE AND FOOT EXTENDS 1/8" PAST THE MAIN DIAMETER MAKING THIS 11" ACROSS AT THE MAIN CROSSPIECES) COVER TOTAL HEIGHT: 1-5/16" (B) MAXIMUM HEIGHT ABOVE MAIN DRAIN BODY: 1-5/16" THE OUTSIDE RING SITS 1/4" ABOVE THE BOTTOM OF THE COVER

************************************************

SCREW HOLES: THIS COVER IS DESIGNED TO ALLOW PLACEMENT OF SCREWS ANYWHERE FROM 5-1/2" TO 7-1/2" APART MEASURED AT THE CENTERLINE OF THE SCREW EACH CROSS BRACE HAS AN OVAL OPENING ON EACH SIDE. EACH OPENING IS ABOUT 3/4" LONG AT THE BOTTOM. AT THE TOP THESE ARE MOLDED TO CONFORM TO THE COUNTERSINK TYPE HEAD OF THE SCREWS. ON ONE BRACE THESE ARE 6-1/4" APART AT THE INSIDE AND ON THE OTHER THEY ARE 5-1/4" APART. SINCE THE OVAL HOLES ARE TAPERED THIS SETS THE SCREW BACK JUST A LITTLE FROM THE EDGE OF EACH OF THE OVAL HOLES. THE INSTRUCTIONS CALL FOR DRILLING 2 ADDITIONAL HOLES INTO THE MAIN DRAIN MUD RING AT A 90 DEGREE OFFSET FROM THE FIRST 2 SCREW USING THE ADDITIONAL 2 OVAL OPENINGS IN THE OTHER CROSS PIECE TO ATTACH THE NEXT 2 SCREWS. THE COVER WILL THEN BE ATTACHED BY A TOTAL OF 4 SCREWS

************************************************

SCREWS: THE SCREWS SUPPLIED WITH THE COVER HAVE A VERY SPECIAL TYPE HEAD WHICH RESEMBLES AN ALLEN HEAD SCREW. THE CORRECT TOOL TO INSTALL THESE IS INCLUDED WITH THE COVER 2 SCREWS - #8 X 1-1/2" SELF TAPPING 2 SCREWS - #8 X 2" SELF TAPPING 2 SCREWS - #8 X 1" SELF TAPPING 2 SCREWS - #10 X 1-1/4" SELF TAPPING 2 SCREWS - #8-32 X 1-1/4 MACHINE THREADS 2 SCREWS - #10-24 X 1-1/4" MACHINE THREADS

************************************************

MARKINGS: DS 360 IS MOLDED INTO ONE OF THE CROSS PIECES ON TOP THE SPECS REQUIRED BY THE VGB-2008 LAW ARE ALSO MOLDED ON THE COVER

Review Summary