Part # 3550-01
Manufacturer Code SPX0540A
Dimensions 10-13/16" x 1-7/8"
FITS THE HAYWARD STARLITE, THE OUTER DIAMETER MEASURES 10 7/8", INNER DIAMETER IS 7", (PLASTIC) THERE ARE 8 MOUNTING BOLTS ON BACK SIDE. MOLDED # ON BACK SIDE (SP540A2)
Is this the correct face for lens that has gasket SP-580-z2 on it. Which i am ordering. My cover only has two mounting screw holes. One at top and bottom. It has 8 mounting studs on back. Both look the same except the other two holes on this one.
Reply
Hi, The Astrolite Plastic Face Rim (SPX0580A) will be the correct part you're looking for.
Reply
this part looks like the one i need for a Hayward Light sp 506
my cover does not have any screws on the back, it clamped around the light /bulb
can i send pictures to you to compare??
Mike
Reply
Hi, Mike. That would be great, you can email pictures to upload@inyopools.com.
Reply
My lens says SP -540-z-1-I and my face ring part says so-560 I am not sure which gasket and Faceframe I need? The face frame has a clamp with one bolt to tighten it ?
Reply
Old rim has this number SP540A2. It is 10 7/8
outer diameter with 8 studs. Is this the same as the one you are selling?
Reply
The Rim, Cycolac Face With Studs (spx0540a) is the correct replacement. It FITS THE HAYWARD STARLITE, THE OUTER DIAMETER MEASURES 10 7/8", INNER DIAMETER IS 7", (PLASTIC) THERE ARE 8 MOUNTING BOLTS ON BACK SIDE. MOLDED # ON BACK SIDE (SP540A2). Hayward Starlite schematic.
Reply
Less than 1 hr
Screwdriver, Wrench Set
2 0
I had very little to base my purchase off of. The old light unit had no markings for what parts to buy. Thankfully The pictures for this product is what saved me. The Hole pattern and Grid on the front lined up with what I had.
This is the rubber gasket SPX540Z2, the new glass lens SPX0540Z1, and light bulb "LED Pool Bulb Color Changing 12V 18W" That worked for my unit.
1. remove the screws holding light plate into the housing unit.
2. if light has long enough cord pull unit out of water and set on ground. (if light cord is not long enough you will need to drain pool below the light housing to avoid getting water into unit when you open it.)
3. look on backside of light housing and remove nuts holding on the face plate.
4.once nuts are off remove faceplate, change out light as needed.
5.recomended replacing the rubber gasket at this point as well. make sure it is seated correctly with lens
6. put the nuts back on the unit and tighten down at a crisscross pattern to apply equal pressure on the rubber gasket.
7. install light unit back into housing, making sure not to pinch or kink wire on back and re install screw into face to mount unit back onto housing.
The Most Helpful Review
1 0
(5 out of 5 stars)
Reviewed By: Garry D. from Bradenton, FL ()
High quality and fast shipping. Even though my pool is at least 20 years old your company had the parts I needed when all local pool supplies did not. Thanks
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars) Light rim
Reviewed By: Susan G. from Middleton, WI ()
It was exactly what we were looking for. We couldn't be more pleased that you carried it.
Was this review helpful to you?
(5 out of 5 stars) Perfect light face!!!!
Reviewed By: John H from Telford, PA ()
Pros: Fit and finish are perfect
Cons: NONE
Perfect part with a perfect fit!!! Thank you! Its looks and works perfectly!
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Chris D. from Deland, FL ()
same as orig, good product
Was this review helpful to you?