Part # STS1152
Warranty 1 Year
Manufacturer Code STS1152R
Dimensions 15" L x 5.5" W x 8" D
**NOTE THIS MOTOR (STS1152R) IS SHIPPED LESS HI-LO SWITCH. YOU MAY PURCHASE THE HI-LO SWITCH SEPARATELY BY ORDERING PART # 1011431-001.**
Voltage 230, High Speed HP = 1.5 Low Speed HP = 1/4, Max Amps @ High HP = 9.0 Max Amps @ Low HP = 3.3, Dual Speed, Round Flange, RPM @ High Speed = 3450 RPM @ Low Speed = 1625, Threaded Shaft, Frame = 56J Used on the following DUAL SPEED pump models: Hayward Max Flow, Hayward Super Pump, Hayward Super II, Hayward Northstar and Jacuzzi Magnum pumps.
Note: NOT California or New York Title 20 Compliant.
California and New York Title 20 Compliant Option:
I would like to replace my Hayward super pump 1.5 HP single speed with a 2 speed Hayward super pump, same HP. You mentioned, we can purchase a toggle switch or a timer. How do you make the electrical connections? I currently have a combination 220 and 110 v outlets by my pump. I just plug my 3 prong cord from the super pump to my outlet, which is connected to my regular timer which is located in my garage approx. 100 ft. away from the pump, filter & gas heater.
Reply
Hi Del, the hayward super pump 1.5 SP2610X152S includes "Hi/Lo" switch on the back of the motor so you would still need to do it manual unless you upgrade to a newer timer or automantion system
Reply
According to the product description of this 1.5 HP super pump, 2 speed replacement motor, it is shipped LESS HI/LOW SWITCH. This means there is no Hi/LO switch? So, how can I manually switch it to Hi or Lo, Joe S? Will this motor fit in my old 1.5 HP Hayward super pump housing? Thanks.
Reply
Hi Del, You are correct this motor does not have a Hi/Lo switch and is only controlled through an outside timer purchased separately. If you want a manual toggle switch for the Hi/Lo then you would need the complete hayward super pump 1.5 HP SP2610X152S which includes the "Hi/Lo" switch on the back of the motor for manual switching of speeds. If you just want to replace the motor then we highly recommend the dual speed motor with integrated digital timer as the installation and wiring is so much easier than the manual switch. The digital timer allows you to manually switch between speeds or you can program the timer to run a different speeds throughout the day. Also the digital timer dual speed motor is less expensive than going with the dual speed motor and then purchasing a separate timer.
Reply
Hi, I am trying to replace a Hayward motor w/ the following specifications:
A.O. Smith Century Two Speed 1081 Pool & Spa
P/N 7-177106-01 HP 1.5 - 2.5 Code G SP1615Z2BC
SF1.3 RPM 3450/1725 AMPS 9.1/3.4
It is controlled with an Blue Haven (Goldline Aqua Logic) controller. Can you help me out with everything I need, i.e correct motor, timer??, replacement seals, gaskets, etc? Thank you, Dave S.
Reply
Hi Dave, The motor on this page would be the correct replacement motor based on the information you supplied. The controller you already have would be fine to control this motor unless the controller has gone bad. As far as the tune up kit goes could you reply back to the email which was sent to you with a couple photos of your pump, this would allow us to recommend the proper tune up kit.
Reply
I have an SP3015EEAZ pump (single speed motor ST1152) that has a bad motor. I want to replace the motor with a dual speed motor like the STS1152. Will the new motor fit?
Reply
Hi Doug, The A.O. Smith 1-1/2 HP Round Flange Dual Speed Full Rate Motor (STS1152R) will be the correct Dual Speed for the Hayward SP3015EEAZ pump. I would recommend getting a Hayward Super II Pump Tune Up Kit (GOKIT2) and a Intermatic Dual Speed Pump Timer (T106R) if you do not have a controller.
Reply
The Most Helpful Review
203 12
(5 out of 5 stars) Excellent Pump Moter Replacement
Reviewed By: PoJo from Clarence, NY ()
Pros: Awesome fit - excellent replacement
Cons: none
Tip to get the impeller off the old pump moter: use a 7/16" open ended wrench - it slides in near the capacitor on the electrical side... rotate the impeller until the wrench slides into place at the end of the shaft and then one person holds the motor and the wrench while a 2nd person loosens the impeller off with bare hands by turning the impeller counter clock-wise.
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Excellent quality!
Was this review helpful to you?
(5 out of 5 stars) Buy it
Reviewed By: Inyo Customer ()
Easy install for do it your self type . Quiet
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Motor was each to replace once I figured out that the wire connections were different from the old motor
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Perfect fit and much quieter
Was this review helpful to you?
(5 out of 5 stars) Works great and shipped fast
Reviewed By: Kevin W. from Orlando, FL ()
Pros: Fast shipment (next day)
Cons: None
Title says it all. Videos helped. I am concerned about the rubber pad that holds the back of the motor up wearing too soon.
Was this review helpful to you?
1 0
(5 out of 5 stars) good price
Reviewed By: Kevin W. from dayton, ohio ()
good price and quick delivery, exactly what was needed
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: JOHN W. from DELAND ()
GREAT PRICE,GREAT DELIVERY TIME,EXACTLY AS ADVERTISED
Was this review helpful to you?