Part # PL2672
Manufacturer Code SPX2610C
Dimensions 4.4" X 0.7"
This is an Aftermarket Replacement Impeller For the Hayward® Super Pump™ 1.5 T.H.P (Total Horse Power) and not the Hayward® original O.E.M Impeller.
Impeller for 1.0 HP full rate and 1.5 HP up rate pumps. Used on several Hayward® pumps including the Max-Flo, Super Pump, Power Flo II and Power Flo III as well as Leslie's® Hydramax pump.
Easy Homeowner Installation
Watch How To Replace A Pool Pump Impeller
Disclaimer:
All manufacturers’ names, brand names, trademarks, images, symbols, descriptions, and part numbers are used herein for reference purposes only.
pump will not flow, lost prime
Reply
There are number of reasons that can cause a pump to lose prime. A clogged line, dirty or old filter, air in the lines, suction air leak at a line or valve, clogged impeller, or even a bad glue at a suction or pressure pump fitting. In any regard either going through the process of elimination testing each possibility or getting a technician to the site would be the next course of action.
Reply
I recently purchased this impeller. the pump motor is a 3/4 HP. I see that this impeller is rated for 1HP. Could using this impeller cause the motor to overheat?
Reply
Hi, Lou I. In order to use the SP2610C impeller you would need a Full Rate 3/4 HP Motor, not an Up-Rate 3/4 HP that's why the motor is overheating. You will need the SP2607C Impeller.
Reply
Hi, If i was mistakenly using a SPX2610C impeller on a SP2607X102S dual speed motor, could this be the reason my motor would overheat and shut off on high speed and function normally on low speed?
Reply
Hi, Shane. Yes, that will explain why your pump is overheating on high speed. The impeller is too larger for the motor. You will need to either increase the motor to STS1102RV1 or decrease the impeller to SPX2607C.
Reply
I'm replacing my 1.5 horsepower motor on my system and want to also replace any parts that may need replacing. The impeller is part number SB2610-C and the existing one looks good but I can't easily turn it by hand. Does that mean it is ready to be replaced?
Reply
Hello,You would only need to change the motor.
Reply
Hi, If i was mistakenly using a SPX2610C impeller on a SP2607X102S dual speed pump, Could this be the reason my pump overheats and shuts off on high speed but works normally on low speed?
Reply
Hi, Shane. Yes, that will explain why your pump is overheating on high speed. The impeller is too larger for the motor. You will need to either increase the motor to STS1102RV1 or decrease the impeller to SPX2607C.
Reply
1 to 2 hrs
5/16 Allen wrench
I replaced the original impeller in the Hayward Super Pump 2600 to match with the high RPM variable speed pool pump motor I installed. I was not difficult to install but did require the purchase of a 5/16th Allen wrench. My set that IO've had forever, largest size was 1/4. Maybe could have used it, as all you need it for is stabilizing the motor shaft to hand tighten the impeller. But I did not want to mess anything up so I bought a new set of Allen Wrenches that included a 5/16th Allen wrench. I'll give my old set to my Son.
Less than 1 hr
Wrench Set
1 0
Upon inspection I discovered the old impeller broke therefore no water was being pumped. Ordered a new impeller for my Hayward Sp and installed it myself. Problem solved. No high cost parts or installation. All DIY and Inyo pools had the best prices.
The Most Helpful Review
4 0
(5 out of 5 stars) Hayward Super Pump Impellor
Reviewed By: Robert R. ()
FINALLY!! Hayward finally made the threaded shaft out of brass. Hopefully it will outlast their pump. Prior to this improvement it had a plastic shaft that wore out from fatigue they cracked and broke. Hayward pumps would be ideal if they would make the commitment to make them waterproof and out of materials that lasted....like this improved part.
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars) Perfect Fit!
Reviewed By: Inyo Customer ()
Worked perfectly on my Hayward Super Pump. Sized for my 1.5hp motor! Very happy
Was this review helpful to you?
(5 out of 5 stars) Nice update!
Reviewed By: Inyo Customer ()
Fits perfect with century motor
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
OE quality fitment!! Could not be happier!!
Was this review helpful to you?
(5 out of 5 stars) Great
Reviewed By: Inyo Customer ()
Great
Was this review helpful to you?
(5 out of 5 stars) INYO how-to videos are the best
Reviewed By: Inyo Customer ()
Works great and easy to install. INYO how to videos are the best.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Good product easy to install
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
When I removed the old Impeller the shaft on it had 2 cracks in it, the shaft was made of plastic. This new impeller has a brass shaft attached so no way it's going to crack.
Was this review helpful to you?